net/ngbe: add WOL and NCSI capability

Support WOL and NCSI capability for devices. And there is one OEM
NCSI NIC which can not be identified from sub-system ID, it needs
to check NCSI pin status in

net/ngbe: add WOL and NCSI capability

Support WOL and NCSI capability for devices. And there is one OEM
NCSI NIC which can not be identified from sub-system ID, it needs
to check NCSI pin status in firmware.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: support link down/up

Add support to set device link down/up.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

net/ngbe: redesign internal PHY init flow

Add to read efuse values from flash, and disable EEE to improve signal
quality. Remove PHY semaphore to access PHY registers faster. And remove
unnecessary

net/ngbe: redesign internal PHY init flow

Add to read efuse values from flash, and disable EEE to improve signal
quality. Remove PHY semaphore to access PHY registers faster. And remove
unnecessary page selection where quick access is required.

When rte_eth_link_get_nowait() is called frequently with LSC disabled by
self-developed applications, eventually the PHY status register will be
accessed frequently. It will cause internal PHY init failure, if they
are done simultaneously. So there is a protection added for internal PHY
init.

Fixes: 3518df5774c7 ("net/ngbe: support device start/stop")
Fixes: 91bc12c5227c ("net/ngbe: optimize PHY initialization process")
Cc: stable@dpdk.org

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: fix external PHY power down

External PHY cannot power down after LAN reset, so need to manually
power down when device stopped.

Fixes: 3d0af7066759 ("net/ngbe: setup PHY link")
Fixes: 1c4

net/ngbe: fix external PHY power down

External PHY cannot power down after LAN reset, so need to manually
power down when device stopped.

Fixes: 3d0af7066759 ("net/ngbe: setup PHY link")
Fixes: 1c44384fce76 ("net/ngbe: support custom PHY interfaces")
Cc: stable@dpdk.org

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: fix reading PHY ID

Change to check low ID register to determine the valid PHY address,
for yt8521s PHY with high ID register value 0. And fix polling
register when expect value is 0, to co

net/ngbe: fix reading PHY ID

Change to check low ID register to determine the valid PHY address,
for yt8521s PHY with high ID register value 0. And fix polling
register when expect value is 0, to complete MDIO read.

Fixes: 44e97550ca68 ("net/ngbe: identify and reset PHY")
Cc: stable@dpdk.org

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: support yt8531s PHY

Add support for yt8531s PHY.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

net/ngbe: fix debug logs

Remove 'DEBUGFUNC' due to too many invalid debug log prints, unify the
DEBUG level macros.

Fixes: cc934df178ab ("net/ngbe: add log and error types")
Cc: stable@dpdk.org

Si

net/ngbe: fix debug logs

Remove 'DEBUGFUNC' due to too many invalid debug log prints, unify the
DEBUG level macros.

Fixes: cc934df178ab ("net/ngbe: add log and error types")
Cc: stable@dpdk.org

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: support custom PHY interfaces

Support sub_device ID 61/62/64 for YT8521S SFP, and 51/52 for M88E1512
PHY.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

net/ngbe: support flow control

Support to get and set flow control.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

net/ngbe: support device start/stop

Setup MSI-X interrupt, complete PHY configuration and set device link
speed to start device. Disable interrupt, stop hardware and clear queues
to stop device.

Si

net/ngbe: support device start/stop

Setup MSI-X interrupt, complete PHY configuration and set device link
speed to start device. Disable interrupt, stop hardware and clear queues
to stop device.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

show more ...

net/ngbe: setup PHY link

Setup PHY, determine link and speed status from PHY.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

net/ngbe: identify and reset PHY

Identify PHY to get the PHY type, and perform a PHY reset.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>