1 /* $NetBSD: sl811hs.c,v 1.22 2009/03/18 10:22:40 cegger Exp $ */ 2 3 /* 4 * Not (c) 2007 Matthew Orgass 5 * This file is public domain, meaning anyone can make any use of part or all 6 * of this file including copying into other works without credit. Any use, 7 * modified or not, is solely the responsibility of the user. If this file is 8 * part of a collection then use in the collection is governed by the terms of 9 * the collection. 10 */ 11 12 /* 13 * Cypress/ScanLogic SL811HS/T USB Host Controller 14 * Datasheet, Errata, and App Note available at www.cypress.com 15 * 16 * Uses: Ratoc CFU1U PCMCIA USB Host Controller, Nereid Mac 68k USB HC, ISA 17 * HCs. The Ratoc CFU2 uses a different chip. 18 * 19 * This chip puts the serial in USB. It implements USB by means of an eight 20 * bit I/O interface. It can be used for ISA, PCMCIA/CF, parallel port, 21 * serial port, or any eight bit interface. It has 256 bytes of memory, the 22 * first 16 of which are used for register access. There are two sets of 23 * registers for sending individual bus transactions. Because USB is polled, 24 * this organization means that some amount of card access must often be made 25 * when devices are attached, even if when they are not directly being used. 26 * A per-ms frame interrupt is necessary and many devices will poll with a 27 * per-frame bulk transfer. 28 * 29 * It is possible to write a little over two bytes to the chip (auto 30 * incremented) per full speed byte time on the USB. Unfortunately, 31 * auto-increment does not work reliably so write and bus speed is 32 * approximately the same for full speed devices. 33 * 34 * In addition to the 240 byte packet size limit for isochronous transfers, 35 * this chip has no means of determining the current frame number other than 36 * getting all 1ms SOF interrupts, which is not always possible even on a fast 37 * system. Isochronous transfers guarantee that transfers will never be 38 * retried in a later frame, so this can cause problems with devices beyond 39 * the difficulty in actually performing the transfer most frames. I tried 40 * implementing isoc transfers and was able to play CD-derrived audio via an 41 * iMic on a 2GHz PC, however it would still be interrupted at times and 42 * once interrupted, would stay out of sync. All isoc support has been 43 * removed. 44 * 45 * BUGS: all chip revisions have problems with low speed devices through hubs. 46 * The chip stops generating SOF with hubs that send SE0 during SOF. See 47 * comment in dointr(). All performance enhancing features of this chip seem 48 * not to work properly, most confirmed buggy in errata doc. 49 * 50 */ 51 52 /* 53 * The hard interrupt is the main entry point. Start, callbacks, and repeat 54 * are the only others called frequently. 55 * 56 * Since this driver attaches to pcmcia, card removal at any point should be 57 * expected and not cause panics or infinite loops. 58 * 59 * This driver does fine grained locking for its own data structures, however 60 * the general USB code does not yet have locks, some of which would need to 61 * be used in this driver. This is mostly for debug use on single processor 62 * systems. Actual MP use of this driver would be unreliable on ports where 63 * splipi is above splhigh unless splipi can be safely blocked when 64 * calculating remaining bus time prior to transfers. 65 * 66 * The theory of the wait lock is that start is the only function that would 67 * be frequently called from arbitrary processors, so it should not need to 68 * wait for the rest to be completed. However, once entering the lock as much 69 * device access as possible is done, so any other CPU that tries to service 70 * an interrupt would be blocked. Ideally, the hard and soft interrupt could 71 * be assigned to the same CPU and start would normally just put work on the 72 * wait queue and generate a soft interrupt. 73 * 74 * Any use of the main lock must check the wait lock before returning. The 75 * aquisition order is main lock then wait lock, but the wait lock must be 76 * released last when clearing the wait queue. 77 */ 78 79 /* XXX TODO: 80 * copy next output packet while transfering 81 * usb suspend 82 * could keep track of known values of all buffer space? 83 * combined print/log function for errors 84 * 85 * use_polling support is untested and may not work 86 */ 87 88 #include <sys/cdefs.h> 89 __KERNEL_RCSID(0, "$NetBSD: sl811hs.c,v 1.22 2009/03/18 10:22:40 cegger Exp $"); 90 91 #include <sys/cdefs.h> 92 #include <sys/param.h> 93 #include <sys/systm.h> 94 #include <sys/kernel.h> 95 #include <sys/proc.h> 96 #include <sys/device.h> 97 #include <sys/malloc.h> 98 #include <sys/queue.h> 99 #include <sys/gcq.h> 100 #include <sys/simplelock.h> 101 #include <sys/intr.h> 102 #include <sys/cpu.h> 103 #include <sys/bus.h> 104 105 #include <dev/usb/usb.h> 106 #include <dev/usb/usbdi.h> 107 #include <dev/usb/usbdivar.h> 108 #include <dev/usb/usb_mem.h> 109 #include <dev/usb/usbdevs.h> 110 #include <dev/usb/usbroothub_subr.h> 111 112 #include <dev/ic/sl811hsreg.h> 113 #include <dev/ic/sl811hsvar.h> 114 115 #define Q_CB 0 /* Control/Bulk */ 116 #define Q_NEXT_CB 1 117 #define Q_MAX_XFER Q_CB 118 #define Q_CALLBACKS 2 119 #define Q_MAX Q_CALLBACKS 120 121 #define F_AREADY (0x00000001) 122 #define F_BREADY (0x00000002) 123 #define F_AINPROG (0x00000004) 124 #define F_BINPROG (0x00000008) 125 #define F_LOWSPEED (0x00000010) 126 #define F_UDISABLED (0x00000020) /* Consider disabled for USB */ 127 #define F_NODEV (0x00000040) 128 #define F_ROOTINTR (0x00000080) 129 #define F_REALPOWER (0x00000100) /* Actual power state */ 130 #define F_POWER (0x00000200) /* USB reported power state */ 131 #define F_ACTIVE (0x00000400) 132 #define F_CALLBACK (0x00000800) /* Callback scheduled */ 133 #define F_SOFCHECK1 (0x00001000) 134 #define F_SOFCHECK2 (0x00002000) 135 #define F_CRESET (0x00004000) /* Reset done not reported */ 136 #define F_CCONNECT (0x00008000) /* Connect change not reported */ 137 #define F_RESET (0x00010000) 138 #define F_ISOC_WARNED (0x00020000) 139 #define F_LSVH_WARNED (0x00040000) 140 141 #define F_DISABLED (F_NODEV|F_UDISABLED) 142 #define F_CHANGE (F_CRESET|F_CCONNECT) 143 144 #ifdef SLHCI_TRY_LSVH 145 unsigned int slhci_try_lsvh = 1; 146 #else 147 unsigned int slhci_try_lsvh = 0; 148 #endif 149 150 #define ADR 0 151 #define LEN 1 152 #define PID 2 153 #define DEV 3 154 #define STAT 2 155 #define CONT 3 156 157 #define A 0 158 #define B 1 159 160 static const uint8_t slhci_tregs[2][4] = 161 {{SL11_E0ADDR, SL11_E0LEN, SL11_E0PID, SL11_E0DEV }, 162 {SL11_E1ADDR, SL11_E1LEN, SL11_E1PID, SL11_E1DEV }}; 163 164 #define PT_ROOT_CTRL 0 165 #define PT_ROOT_INTR 1 166 #define PT_CTRL_SETUP 2 167 #define PT_CTRL_DATA 3 168 #define PT_CTRL_STATUS 4 169 #define PT_INTR 5 170 #define PT_BULK 6 171 #define PT_MAX 6 172 173 #ifdef SLHCI_DEBUG 174 #define SLHCI_MEM_ACCOUNTING 175 static const char * 176 pnames(int ptype) 177 { 178 static const char * const names[] = { "ROOT Ctrl", "ROOT Intr", 179 "Control (setup)", "Control (data)", "Control (status)", 180 "Interrupt", "Bulk", "BAD PTYPE" }; 181 182 KASSERT(sizeof(names) / sizeof(names[0]) == PT_MAX + 2); 183 if (ptype > PT_MAX) 184 ptype = PT_MAX + 1; 185 return names[ptype]; 186 } 187 #endif 188 189 #define SLHCI_XFER_TYPE(x) (((struct slhci_pipe *)((x)->pipe))->ptype) 190 191 /* Maximum allowable reserved bus time. Since intr/isoc transfers have 192 * unconditional priority, this is all that ensures control and bulk transfers 193 * get a chance. It is a single value for all frames since all transfers can 194 * use multiple consecutive frames if an error is encountered. Note that it 195 * is not really possible to fill the bus with transfers, so this value should 196 * be on the low side. Defaults to giving a warning unless SLHCI_NO_OVERTIME 197 * is defined. Full time is 12000 - END_BUSTIME. */ 198 #ifndef SLHCI_RESERVED_BUSTIME 199 #define SLHCI_RESERVED_BUSTIME 5000 200 #endif 201 202 /* Rate for "exceeds reserved bus time" warnings (default) or errors. 203 * Warnings only happen when an endpoint open causes the time to go above 204 * SLHCI_RESERVED_BUSTIME, not if it is already above. */ 205 #ifndef SLHCI_OVERTIME_WARNING_RATE 206 #define SLHCI_OVERTIME_WARNING_RATE { 60, 0 } /* 60 seconds */ 207 #endif 208 static const struct timeval reserved_warn_rate = SLHCI_OVERTIME_WARNING_RATE; 209 210 /* Rate for overflow warnings */ 211 #ifndef SLHCI_OVERFLOW_WARNING_RATE 212 #define SLHCI_OVERFLOW_WARNING_RATE { 60, 0 } /* 60 seconds */ 213 #endif 214 static const struct timeval overflow_warn_rate = SLHCI_OVERFLOW_WARNING_RATE; 215 216 /* For EOF, the spec says 42 bit times, plus (I think) a possible hub skew of 217 * 20 bit times. By default leave 66 bit times to start the transfer beyond 218 * the required time. Units are full-speed bit times (a bit over 5us per 64). 219 * Only multiples of 64 are significant. */ 220 #define SLHCI_STANDARD_END_BUSTIME 128 221 #ifndef SLHCI_EXTRA_END_BUSTIME 222 #define SLHCI_EXTRA_END_BUSTIME 0 223 #endif 224 225 #define SLHCI_END_BUSTIME (SLHCI_STANDARD_END_BUSTIME+SLHCI_EXTRA_END_BUSTIME) 226 227 /* This is an approximation of the USB worst-case timings presented on p. 54 of 228 * the USB 1.1 spec translated to full speed bit times. 229 * FS = full speed with handshake, FSII = isoc in, FSIO = isoc out, 230 * FSI = isoc (worst case), LS = low speed */ 231 #define SLHCI_FS_CONST 114 232 #define SLHCI_FSII_CONST 92 233 #define SLHCI_FSIO_CONST 80 234 #define SLHCI_FSI_CONST 92 235 #define SLHCI_LS_CONST 804 236 #ifndef SLHCI_PRECICE_BUSTIME 237 /* These values are < 3% too high (compared to the multiply and divide) for 238 * max sized packets. */ 239 #define SLHCI_FS_DATA_TIME(len) (((u_int)(len)<<3)+(len)+((len)>>1)) 240 #define SLHCI_LS_DATA_TIME(len) (((u_int)(len)<<6)+((u_int)(len)<<4)) 241 #else 242 #define SLHCI_FS_DATA_TIME(len) (56*(len)/6) 243 #define SLHCI_LS_DATA_TIME(len) (449*(len)/6) 244 #endif 245 246 /* Set SLHCI_WAIT_SIZE to the desired maximum size of single FS transfer 247 * to poll for after starting a transfer. 64 gets all full speed transfers. 248 * Note that even if 0 polling will occur if data equal or greater than the 249 * transfer size is copied to the chip while the transfer is in progress. 250 * Setting SLHCI_WAIT_TIME to -12000 will disable polling. 251 */ 252 #ifndef SLHCI_WAIT_SIZE 253 #define SLHCI_WAIT_SIZE 8 254 #endif 255 #ifndef SLHCI_WAIT_TIME 256 #define SLHCI_WAIT_TIME (SLHCI_FS_CONST + \ 257 SLHCI_FS_DATA_TIME(SLHCI_WAIT_SIZE)) 258 #endif 259 const int slhci_wait_time = SLHCI_WAIT_TIME; 260 261 /* Root hub intr endpoint */ 262 #define ROOT_INTR_ENDPT 1 263 264 #ifndef SLHCI_MAX_RETRIES 265 #define SLHCI_MAX_RETRIES 3 266 #endif 267 268 /* Check IER values for corruption after this many unrecognized interrupts. */ 269 #ifndef SLHCI_IER_CHECK_FREQUENCY 270 #ifdef SLHCI_DEBUG 271 #define SLHCI_IER_CHECK_FREQUENCY 1 272 #else 273 #define SLHCI_IER_CHECK_FREQUENCY 100 274 #endif 275 #endif 276 277 /* Note that buffer points to the start of the buffer for this transfer. */ 278 struct slhci_pipe { 279 struct usbd_pipe pipe; 280 struct usbd_xfer *xfer; /* xfer in progress */ 281 uint8_t *buffer; /* I/O buffer (if needed) */ 282 struct gcq ap; /* All pipes */ 283 struct gcq to; /* Timeout list */ 284 struct gcq xq; /* Xfer queues */ 285 unsigned int pflags; /* Pipe flags */ 286 #define PF_GONE (0x01) /* Pipe is on disabled device */ 287 #define PF_TOGGLE (0x02) /* Data toggle status */ 288 #define PF_LS (0x04) /* Pipe is low speed */ 289 #define PF_PREAMBLE (0x08) /* Needs preamble */ 290 Frame to_frame; /* Frame number for timeout */ 291 Frame frame; /* Frame number for intr xfer */ 292 Frame lastframe; /* Previous frame number for intr */ 293 uint16_t bustime; /* Worst case bus time usage */ 294 uint16_t newbustime[2]; /* new bustimes (see index below) */ 295 uint8_t tregs[4]; /* ADR, LEN, PID, DEV */ 296 uint8_t newlen[2]; /* 0 = short data, 1 = ctrl data */ 297 uint8_t newpid; /* for ctrl */ 298 uint8_t wantshort; /* last xfer must be short */ 299 uint8_t control; /* Host control register settings */ 300 uint8_t nerrs; /* Current number of errors */ 301 uint8_t ptype; /* Pipe type */ 302 }; 303 304 #if defined(MULTIPROCESSOR) || defined(LOCKDEBUG) 305 #define SLHCI_WAITLOCK 1 306 #endif 307 308 #ifdef SLHCI_PROFILE_TRANSFER 309 #if defined(__mips__) 310 /* MIPS cycle counter does not directly count cpu cycles but is a different 311 * fraction of cpu cycles depending on the cpu. */ 312 typedef u_int32_t cc_type; 313 #define CC_TYPE_FMT "%u" 314 #define slhci_cc_set(x) __asm volatile ("mfc0 %[cc], $9\n\tnop\n\tnop\n\tnop" \ 315 : [cc] "=r"(x)) 316 #elif defined(__i386__) 317 typedef u_int64_t cc_type; 318 #define CC_TYPE_FMT "%llu" 319 #define slhci_cc_set(x) __asm volatile ("rdtsc" : "=A"(x)) 320 #else 321 #error "SLHCI_PROFILE_TRANSFER not implemented on this MACHINE_ARCH (see sys/dev/ic/sl811hs.c)" 322 #endif 323 struct slhci_cc_time { 324 cc_type start; 325 cc_type stop; 326 unsigned int miscdata; 327 }; 328 #ifndef SLHCI_N_TIMES 329 #define SLHCI_N_TIMES 200 330 #endif 331 struct slhci_cc_times { 332 struct slhci_cc_time times[SLHCI_N_TIMES]; 333 int current; 334 int wraparound; 335 }; 336 337 static struct slhci_cc_times t_ab[2]; 338 static struct slhci_cc_times t_abdone; 339 static struct slhci_cc_times t_copy_to_dev; 340 static struct slhci_cc_times t_copy_from_dev; 341 static struct slhci_cc_times t_intr; 342 static struct slhci_cc_times t_lock; 343 static struct slhci_cc_times t_delay; 344 static struct slhci_cc_times t_hard_int; 345 static struct slhci_cc_times t_callback; 346 347 static inline void 348 start_cc_time(struct slhci_cc_times *times, unsigned int misc) { 349 times->times[times->current].miscdata = misc; 350 slhci_cc_set(times->times[times->current].start); 351 } 352 static inline void 353 stop_cc_time(struct slhci_cc_times *times) { 354 slhci_cc_set(times->times[times->current].stop); 355 if (++times->current >= SLHCI_N_TIMES) { 356 times->current = 0; 357 times->wraparound = 1; 358 } 359 } 360 361 void slhci_dump_cc_times(int); 362 363 void 364 slhci_dump_cc_times(int n) { 365 struct slhci_cc_times *times; 366 int i; 367 368 switch (n) { 369 default: 370 case 0: 371 printf("USBA start transfer to intr:\n"); 372 times = &t_ab[A]; 373 break; 374 case 1: 375 printf("USBB start transfer to intr:\n"); 376 times = &t_ab[B]; 377 break; 378 case 2: 379 printf("abdone:\n"); 380 times = &t_abdone; 381 break; 382 case 3: 383 printf("copy to device:\n"); 384 times = &t_copy_to_dev; 385 break; 386 case 4: 387 printf("copy from device:\n"); 388 times = &t_copy_from_dev; 389 break; 390 case 5: 391 printf("intr to intr:\n"); 392 times = &t_intr; 393 break; 394 case 6: 395 printf("lock to release:\n"); 396 times = &t_lock; 397 break; 398 case 7: 399 printf("delay time:\n"); 400 times = &t_delay; 401 break; 402 case 8: 403 printf("hard interrupt enter to exit:\n"); 404 times = &t_hard_int; 405 break; 406 case 9: 407 printf("callback:\n"); 408 times = &t_callback; 409 break; 410 } 411 412 if (times->wraparound) 413 for (i = times->current + 1; i < SLHCI_N_TIMES; i++) 414 printf("start " CC_TYPE_FMT " stop " CC_TYPE_FMT 415 " difference %8i miscdata %#x\n", 416 times->times[i].start, times->times[i].stop, 417 (int)(times->times[i].stop - 418 times->times[i].start), times->times[i].miscdata); 419 420 for (i = 0; i < times->current; i++) 421 printf("start " CC_TYPE_FMT " stop " CC_TYPE_FMT 422 " difference %8i miscdata %#x\n", times->times[i].start, 423 times->times[i].stop, (int)(times->times[i].stop - 424 times->times[i].start), times->times[i].miscdata); 425 } 426 #else 427 #define start_cc_time(x, y) 428 #define stop_cc_time(x) 429 #endif /* SLHCI_PROFILE_TRANSFER */ 430 431 typedef usbd_status (*LockCallFunc)(struct slhci_softc *, struct slhci_pipe 432 *, struct usbd_xfer *); 433 434 usbd_status slhci_allocm(struct usbd_bus *, usb_dma_t *, u_int32_t); 435 void slhci_freem(struct usbd_bus *, usb_dma_t *); 436 struct usbd_xfer * slhci_allocx(struct usbd_bus *); 437 void slhci_freex(struct usbd_bus *, struct usbd_xfer *); 438 439 usbd_status slhci_transfer(struct usbd_xfer *); 440 usbd_status slhci_start(struct usbd_xfer *); 441 usbd_status slhci_root_start(struct usbd_xfer *); 442 usbd_status slhci_open(struct usbd_pipe *); 443 444 /* slhci_supported_rev, slhci_preinit, slhci_attach, slhci_detach, 445 * slhci_activate */ 446 447 void slhci_abort(struct usbd_xfer *); 448 void slhci_close(struct usbd_pipe *); 449 void slhci_clear_toggle(struct usbd_pipe *); 450 void slhci_poll(struct usbd_bus *); 451 void slhci_done(struct usbd_xfer *); 452 void slhci_void(void *); 453 454 /* lock entry functions */ 455 456 #ifdef SLHCI_MEM_ACCOUNTING 457 void slhci_mem_use(struct usbd_bus *, int); 458 #endif 459 460 void slhci_reset_entry(void *); 461 usbd_status slhci_lock_call(struct slhci_softc *, LockCallFunc, 462 struct slhci_pipe *, struct usbd_xfer *); 463 void slhci_start_entry(struct slhci_softc *, struct slhci_pipe *); 464 void slhci_callback_entry(void *arg); 465 void slhci_do_callback(struct slhci_softc *, struct usbd_xfer *, int *); 466 467 /* slhci_intr */ 468 469 void slhci_main(struct slhci_softc *, int *); 470 471 /* in lock functions */ 472 473 static void slhci_write(struct slhci_softc *, uint8_t, uint8_t); 474 static uint8_t slhci_read(struct slhci_softc *, uint8_t); 475 static void slhci_write_multi(struct slhci_softc *, uint8_t, uint8_t *, int); 476 static void slhci_read_multi(struct slhci_softc *, uint8_t, uint8_t *, int); 477 478 static void slhci_waitintr(struct slhci_softc *, int); 479 static int slhci_dointr(struct slhci_softc *); 480 static void slhci_abdone(struct slhci_softc *, int); 481 static void slhci_tstart(struct slhci_softc *); 482 static void slhci_dotransfer(struct slhci_softc *); 483 484 static void slhci_callback(struct slhci_softc *, int *); 485 static void slhci_enter_xfer(struct slhci_softc *, struct slhci_pipe *); 486 #ifdef SLHCI_WAITLOCK 487 static void slhci_enter_xfers(struct slhci_softc *); 488 #endif 489 static void slhci_queue_timed(struct slhci_softc *, struct slhci_pipe *); 490 static void slhci_xfer_timer(struct slhci_softc *, struct slhci_pipe *); 491 492 static void slhci_do_repeat(struct slhci_softc *, struct usbd_xfer *); 493 static void slhci_callback_schedule(struct slhci_softc *); 494 static void slhci_do_callback_schedule(struct slhci_softc *); 495 #if 0 496 void slhci_pollxfer(struct slhci_softc *, struct usbd_xfer *, int *); /* XXX */ 497 #endif 498 499 static usbd_status slhci_do_poll(struct slhci_softc *, struct slhci_pipe *, 500 struct usbd_xfer *); 501 static usbd_status slhci_lsvh_warn(struct slhci_softc *, struct slhci_pipe *, 502 struct usbd_xfer *); 503 static usbd_status slhci_isoc_warn(struct slhci_softc *, struct slhci_pipe *, 504 struct usbd_xfer *); 505 static usbd_status slhci_open_pipe(struct slhci_softc *, struct slhci_pipe *, 506 struct usbd_xfer *); 507 static usbd_status slhci_close_pipe(struct slhci_softc *, struct slhci_pipe *, 508 struct usbd_xfer *); 509 static usbd_status slhci_do_abort(struct slhci_softc *, struct slhci_pipe *, 510 struct usbd_xfer *); 511 static usbd_status slhci_do_attach(struct slhci_softc *, struct slhci_pipe *, 512 struct usbd_xfer *); 513 static usbd_status slhci_halt(struct slhci_softc *, struct slhci_pipe *, 514 struct usbd_xfer *); 515 516 static void slhci_intrchange(struct slhci_softc *, uint8_t); 517 static void slhci_drain(struct slhci_softc *); 518 static void slhci_reset(struct slhci_softc *); 519 static int slhci_reserve_bustime(struct slhci_softc *, struct slhci_pipe *, 520 int); 521 static void slhci_insert(struct slhci_softc *); 522 523 static usbd_status slhci_clear_feature(struct slhci_softc *, unsigned int); 524 static usbd_status slhci_set_feature(struct slhci_softc *, unsigned int); 525 static void slhci_get_status(struct slhci_softc *, usb_port_status_t *); 526 static usbd_status slhci_root(struct slhci_softc *, struct slhci_pipe *, 527 struct usbd_xfer *); 528 529 #ifdef SLHCI_DEBUG 530 void slhci_log_buffer(struct usbd_xfer *); 531 void slhci_log_req(usb_device_request_t *); 532 void slhci_log_req_hub(usb_device_request_t *); 533 void slhci_log_dumpreg(void); 534 void slhci_log_xfer(struct usbd_xfer *); 535 void slhci_log_spipe(struct slhci_pipe *); 536 void slhci_print_intr(void); 537 void slhci_log_sc(void); 538 void slhci_log_slreq(struct slhci_pipe *); 539 540 extern int usbdebug; 541 542 /* Constified so you can read the values from ddb */ 543 const int SLHCI_D_TRACE = 0x0001; 544 const int SLHCI_D_MSG = 0x0002; 545 const int SLHCI_D_XFER = 0x0004; 546 const int SLHCI_D_MEM = 0x0008; 547 const int SLHCI_D_INTR = 0x0010; 548 const int SLHCI_D_SXFER = 0x0020; 549 const int SLHCI_D_ERR = 0x0080; 550 const int SLHCI_D_BUF = 0x0100; 551 const int SLHCI_D_SOFT = 0x0200; 552 const int SLHCI_D_WAIT = 0x0400; 553 const int SLHCI_D_ROOT = 0x0800; 554 /* SOF/NAK alone normally ignored, SOF also needs D_INTR */ 555 const int SLHCI_D_SOF = 0x1000; 556 const int SLHCI_D_NAK = 0x2000; 557 558 int slhci_debug = 0x1cbc; /* 0xc8c; */ /* 0xffff; */ /* 0xd8c; */ 559 struct slhci_softc *ssc; 560 #ifdef USB_DEBUG 561 int slhci_usbdebug = -1; /* value to set usbdebug on attach, -1 = leave alone */ 562 #endif 563 564 /* Add UVMHIST history for debugging: 565 * 566 * Before uvm_hist in sys/uvm/uvm_stat.c add: 567 * UVMHIST_DECL(slhcihist); 568 * 569 * In uvm_hist add: 570 * if ((bitmask & UVMHIST_SLHCI)) 571 * hists[i++] = &slhcihist; 572 * 573 * In sys/uvm/uvm_stat.h add UVMHIST_SLHCI define. 574 */ 575 576 #include <uvm/uvm_stat.h> 577 UVMHIST_DECL(slhcihist); 578 579 #if !defined(UVMHIST) || !defined(UVMHIST_SLHCI) 580 #error "SLHCI_DEBUG requires UVMHIST (with modifications, see sys/dev/ic/sl81hs.c)" 581 #endif 582 583 #ifndef SLHCI_NHIST 584 #define SLHCI_NHIST 409600 585 #endif 586 const unsigned int SLHCI_HISTMASK = UVMHIST_SLHCI; 587 struct uvm_history_ent slhci_he[SLHCI_NHIST]; 588 589 #define SLHCI_DEXEC(x, y) do { if ((slhci_debug & SLHCI_ ## x)) { y; } \ 590 } while (/*CONSTCOND*/ 0) 591 #define DDOLOG(f, a, b, c, d) do { const char *_uvmhist_name = __func__; \ 592 u_long _uvmhist_call = 0; UVMHIST_LOG(slhcihist, f, a, b, c, d); \ 593 } while (/*CONSTCOND*/0) 594 #define DLOG(x, f, a, b, c, d) SLHCI_DEXEC(x, DDOLOG(f, a, b, c, d)) 595 /* DLOGFLAG8 is a macro not a function so that flag name expressions are not 596 * evaluated unless the flag bit is set (which could save a register read). 597 * x is debug mask, y is flag identifier, z is flag variable, 598 * a-h are flag names (must evaluate to string constants, msb first). */ 599 #define DDOLOGFLAG8(y, z, a, b, c, d, e, f, g, h) do { uint8_t _DLF8 = (z); \ 600 const char *_uvmhist_name = __func__; u_long _uvmhist_call = 0; \ 601 if (_DLF8 & 0xf0) UVMHIST_LOG(slhcihist, y " %s %s %s %s", _DLF8 & 0x80 ? \ 602 (a) : "", _DLF8 & 0x40 ? (b) : "", _DLF8 & 0x20 ? (c) : "", _DLF8 & 0x10 ? \ 603 (d) : ""); if (_DLF8 & 0x0f) UVMHIST_LOG(slhcihist, y " %s %s %s %s", \ 604 _DLF8 & 0x08 ? (e) : "", _DLF8 & 0x04 ? (f) : "", _DLF8 & 0x02 ? (g) : "", \ 605 _DLF8 & 0x01 ? (h) : ""); \ 606 } while (/*CONSTCOND*/ 0) 607 #define DLOGFLAG8(x, y, z, a, b, c, d, e, f, g, h) \ 608 SLHCI_DEXEC(x, DDOLOGFLAG8(y, z, a, b, c, d, e, f, g, h)) 609 /* DDOLOGBUF logs a buffer up to 8 bytes at a time. No identifier so that we 610 * can make it a real function. */ 611 static void 612 DDOLOGBUF(uint8_t *buf, unsigned int length) 613 { 614 int i; 615 616 for(i=0; i+8 <= length; i+=8) 617 DDOLOG("%.4x %.4x %.4x %.4x", (buf[i] << 8) | buf[i+1], 618 (buf[i+2] << 8) | buf[i+3], (buf[i+4] << 8) | buf[i+5], 619 (buf[i+6] << 8) | buf[i+7]); 620 if (length == i+7) 621 DDOLOG("%.4x %.4x %.4x %.2x", (buf[i] << 8) | buf[i+1], 622 (buf[i+2] << 8) | buf[i+3], (buf[i+4] << 8) | buf[i+5], 623 buf[i+6]); 624 else if (length == i+6) 625 DDOLOG("%.4x %.4x %.4x", (buf[i] << 8) | buf[i+1], 626 (buf[i+2] << 8) | buf[i+3], (buf[i+4] << 8) | buf[i+5], 0); 627 else if (length == i+5) 628 DDOLOG("%.4x %.4x %.2x", (buf[i] << 8) | buf[i+1], 629 (buf[i+2] << 8) | buf[i+3], buf[i+4], 0); 630 else if (length == i+4) 631 DDOLOG("%.4x %.4x", (buf[i] << 8) | buf[i+1], 632 (buf[i+2] << 8) | buf[i+3], 0,0); 633 else if (length == i+3) 634 DDOLOG("%.4x %.2x", (buf[i] << 8) | buf[i+1], buf[i+2], 0,0); 635 else if (length == i+2) 636 DDOLOG("%.4x", (buf[i] << 8) | buf[i+1], 0,0,0); 637 else if (length == i+1) 638 DDOLOG("%.2x", buf[i], 0,0,0); 639 } 640 #define DLOGBUF(x, b, l) SLHCI_DEXEC(x, DDOLOGBUF(b, l)) 641 #else /* now !SLHCI_DEBUG */ 642 #define slhci_log_spipe(spipe) ((void)0) 643 #define slhci_log_xfer(xfer) ((void)0) 644 #define SLHCI_DEXEC(x, y) ((void)0) 645 #define DDOLOG(f, a, b, c, d) ((void)0) 646 #define DLOG(x, f, a, b, c, d) ((void)0) 647 #define DDOLOGFLAG8(y, z, a, b, c, d, e, f, g, h) ((void)0) 648 #define DLOGFLAG8(x, y, z, a, b, c, d, e, f, g, h) ((void)0) 649 #define DDOLOGBUF(b, l) ((void)0) 650 #define DLOGBUF(x, b, l) ((void)0) 651 #endif /* SLHCI_DEBUG */ 652 653 #define SLHCI_MAINLOCKASSERT(sc) ((void)0) 654 #define SLHCI_LOCKASSERT(sc, main, wait) ((void)0) 655 656 #ifdef DIAGNOSTIC 657 #define LK_SLASSERT(exp, sc, spipe, xfer, ext) do { \ 658 if (!(exp)) { \ 659 printf("%s: assertion %s failed line %u function %s!" \ 660 " halted\n", SC_NAME(sc), #exp, __LINE__, __func__);\ 661 DDOLOG("%s: assertion %s failed line %u function %s!" \ 662 " halted\n", SC_NAME(sc), #exp, __LINE__, __func__);\ 663 slhci_halt(sc, spipe, xfer); \ 664 ext; \ 665 } \ 666 } while (/*CONSTCOND*/0) 667 #define UL_SLASSERT(exp, sc, spipe, xfer, ext) do { \ 668 if (!(exp)) { \ 669 printf("%s: assertion %s failed line %u function %s!" \ 670 " halted\n", SC_NAME(sc), #exp, __LINE__, __func__); \ 671 DDOLOG("%s: assertion %s failed line %u function %s!" \ 672 " halted\n", SC_NAME(sc), #exp, __LINE__, __func__); \ 673 slhci_lock_call(sc, &slhci_halt, spipe, xfer); \ 674 ext; \ 675 } \ 676 } while (/*CONSTCOND*/0) 677 #else 678 #define LK_SLASSERT(exp, sc, spipe, xfer, ext) ((void)0) 679 #define UL_SLASSERT(exp, sc, spipe, xfer, ext) ((void)0) 680 #endif 681 682 const struct usbd_bus_methods slhci_bus_methods = { 683 slhci_open, 684 slhci_void, 685 slhci_poll, 686 slhci_allocm, 687 slhci_freem, 688 slhci_allocx, 689 slhci_freex, 690 }; 691 692 const struct usbd_pipe_methods slhci_pipe_methods = { 693 slhci_transfer, 694 slhci_start, 695 slhci_abort, 696 slhci_close, 697 slhci_clear_toggle, 698 slhci_done, 699 }; 700 701 const struct usbd_pipe_methods slhci_root_methods = { 702 slhci_transfer, 703 slhci_root_start, 704 slhci_abort, 705 (void (*)(struct usbd_pipe *))slhci_void, /* XXX safe? */ 706 slhci_clear_toggle, 707 slhci_done, 708 }; 709 710 /* Queue inlines */ 711 712 #define GOT_FIRST_TO(tvar, t) \ 713 GCQ_GOT_FIRST_TYPED(tvar, &(t)->to, struct slhci_pipe, to) 714 715 #define FIND_TO(var, t, tvar, cond) \ 716 GCQ_FIND_TYPED(var, &(t)->to, tvar, struct slhci_pipe, to, cond) 717 718 #define FOREACH_AP(var, t, tvar) \ 719 GCQ_FOREACH_TYPED(var, &(t)->ap, tvar, struct slhci_pipe, ap) 720 721 #define GOT_FIRST_TIMED_COND(tvar, t, cond) \ 722 GCQ_GOT_FIRST_COND_TYPED(tvar, &(t)->timed, struct slhci_pipe, xq, cond) 723 724 #define GOT_FIRST_CB(tvar, t) \ 725 GCQ_GOT_FIRST_TYPED(tvar, &(t)->q[Q_CB], struct slhci_pipe, xq) 726 727 #define DEQUEUED_CALLBACK(tvar, t) \ 728 GCQ_DEQUEUED_FIRST_TYPED(tvar, &(t)->q[Q_CALLBACKS], struct slhci_pipe, xq) 729 730 #define FIND_TIMED(var, t, tvar, cond) \ 731 GCQ_FIND_TYPED(var, &(t)->timed, tvar, struct slhci_pipe, xq, cond) 732 733 #ifdef SLHCI_WAITLOCK 734 #define DEQUEUED_WAITQ(tvar, sc) \ 735 GCQ_DEQUEUED_FIRST_TYPED(tvar, &(sc)->sc_waitq, struct slhci_pipe, xq) 736 737 static inline void 738 enter_waitq(struct slhci_softc *sc, struct slhci_pipe *spipe) 739 { 740 gcq_insert_tail(&sc->sc_waitq, &spipe->xq); 741 } 742 #endif 743 744 static inline void 745 enter_q(struct slhci_transfers *t, struct slhci_pipe *spipe, int i) 746 { 747 gcq_insert_tail(&t->q[i], &spipe->xq); 748 } 749 750 static inline void 751 enter_callback(struct slhci_transfers *t, struct slhci_pipe *spipe) 752 { 753 gcq_insert_tail(&t->q[Q_CALLBACKS], &spipe->xq); 754 } 755 756 static inline void 757 enter_all_pipes(struct slhci_transfers *t, struct slhci_pipe *spipe) 758 { 759 gcq_insert_tail(&t->ap, &spipe->ap); 760 } 761 762 /* Start out of lock functions. */ 763 764 struct slhci_mem { 765 usb_dma_block_t block; 766 uint8_t data[]; 767 }; 768 769 /* The SL811HS does not do DMA as a host controller, but NetBSD's USB interface 770 * assumes DMA is used. So we fake the DMA block. */ 771 usbd_status 772 slhci_allocm(struct usbd_bus *bus, usb_dma_t *dma, u_int32_t size) 773 { 774 struct slhci_mem *mem; 775 776 mem = malloc(sizeof(struct slhci_mem) + size, M_USB, M_NOWAIT|M_ZERO); 777 778 DLOG(D_MEM, "allocm %p", mem, 0,0,0); 779 780 if (mem == NULL) 781 return USBD_NOMEM; 782 783 dma->block = &mem->block; 784 dma->block->kaddr = mem->data; 785 786 /* dma->offs = 0; */ 787 dma->block->nsegs = 1; 788 dma->block->size = size; 789 dma->block->align = size; 790 dma->block->flags |= USB_DMA_FULLBLOCK; 791 792 #ifdef SLHCI_MEM_ACCOUNTING 793 slhci_mem_use(bus, 1); 794 #endif 795 796 return USBD_NORMAL_COMPLETION; 797 } 798 799 void 800 slhci_freem(struct usbd_bus *bus, usb_dma_t *dma) 801 { 802 DLOG(D_MEM, "freem %p", dma->block, 0,0,0); 803 804 #ifdef SLHCI_MEM_ACCOUNTING 805 slhci_mem_use(bus, -1); 806 #endif 807 808 free(dma->block, M_USB); 809 } 810 811 struct usbd_xfer * 812 slhci_allocx(struct usbd_bus *bus) 813 { 814 struct usbd_xfer *xfer; 815 816 xfer = malloc(sizeof(*xfer), M_USB, M_NOWAIT|M_ZERO); 817 818 DLOG(D_MEM, "allocx %p", xfer, 0,0,0); 819 820 #ifdef SLHCI_MEM_ACCOUNTING 821 slhci_mem_use(bus, 1); 822 #endif 823 #ifdef DIAGNOSTIC 824 if (xfer != NULL) 825 xfer->busy_free = XFER_BUSY; 826 #endif 827 return xfer; 828 } 829 830 void 831 slhci_freex(struct usbd_bus *bus, struct usbd_xfer *xfer) 832 { 833 DLOG(D_MEM, "freex xfer %p spipe %p", xfer, xfer->pipe,0,0); 834 835 #ifdef SLHCI_MEM_ACCOUNTING 836 slhci_mem_use(bus, -1); 837 #endif 838 #ifdef DIAGNOSTIC 839 if (xfer->busy_free != XFER_BUSY) { 840 struct slhci_softc *sc = bus->hci_private; 841 printf("%s: slhci_freex: xfer=%p not busy, %#08x halted\n", 842 SC_NAME(sc), xfer, xfer->busy_free); 843 DDOLOG("%s: slhci_freex: xfer=%p not busy, %#08x halted\n", 844 SC_NAME(sc), xfer, xfer->busy_free, 0); 845 slhci_lock_call(sc, &slhci_halt, NULL, NULL); 846 return; 847 } 848 xfer->busy_free = XFER_FREE; 849 #endif 850 851 free(xfer, M_USB); 852 } 853 854 usbd_status 855 slhci_transfer(struct usbd_xfer *xfer) 856 { 857 usbd_status error; 858 int s; 859 860 DLOG(D_TRACE, "%s transfer xfer %p spipe %p ", 861 pnames(SLHCI_XFER_TYPE(xfer)), xfer, xfer->pipe,0); 862 863 /* Insert last in queue */ 864 error = usb_insert_transfer(xfer); 865 if (error) { 866 if (error != USBD_IN_PROGRESS) 867 DLOG(D_ERR, "usb_insert_transfer returns %d!", error, 868 0,0,0); 869 return error; 870 } 871 872 /* 873 * Pipe isn't running (otherwise error would be USBD_INPROG), 874 * so start it first. 875 */ 876 877 /* Start next is always done at splsoftusb, so we do this here so 878 * start functions are always called at softusb. XXX */ 879 s = splsoftusb(); 880 error = xfer->pipe->methods->start(SIMPLEQ_FIRST(&xfer->pipe->queue)); 881 splx(s); 882 883 return error; 884 } 885 886 /* It is not safe for start to return anything other than USBD_INPROG. */ 887 usbd_status 888 slhci_start(struct usbd_xfer *xfer) 889 { 890 struct slhci_softc *sc; 891 struct usbd_pipe *pipe; 892 struct slhci_pipe *spipe; 893 struct slhci_transfers *t; 894 usb_endpoint_descriptor_t *ed; 895 unsigned int max_packet; 896 897 pipe = xfer->pipe; 898 sc = pipe->device->bus->hci_private; 899 spipe = (struct slhci_pipe *)xfer->pipe; 900 t = &sc->sc_transfers; 901 ed = pipe->endpoint->edesc; 902 903 max_packet = UGETW(ed->wMaxPacketSize); 904 905 DLOG(D_TRACE, "%s start xfer %p spipe %p length %d", 906 pnames(spipe->ptype), xfer, spipe, xfer->length); 907 908 /* root transfers use slhci_root_start */ 909 910 KASSERT(spipe->xfer == NULL); /* not SLASSERT */ 911 912 xfer->actlen = 0; 913 xfer->status = USBD_IN_PROGRESS; 914 915 spipe->xfer = xfer; 916 917 spipe->nerrs = 0; 918 spipe->frame = t->frame; 919 spipe->control = SL11_EPCTRL_ARM_ENABLE; 920 spipe->tregs[DEV] = pipe->device->address; 921 spipe->tregs[PID] = spipe->newpid = UE_GET_ADDR(ed->bEndpointAddress) 922 | (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN ? SL11_PID_IN : 923 SL11_PID_OUT); 924 spipe->newlen[0] = xfer->length % max_packet; 925 spipe->newlen[1] = min(xfer->length, max_packet); 926 927 if (spipe->ptype == PT_BULK || spipe->ptype == PT_INTR) { 928 if (spipe->pflags & PF_TOGGLE) 929 spipe->control |= SL11_EPCTRL_DATATOGGLE; 930 spipe->tregs[LEN] = spipe->newlen[1]; 931 if (spipe->tregs[LEN]) 932 spipe->buffer = KERNADDR(&xfer->dmabuf, 0); 933 else 934 spipe->buffer = NULL; 935 spipe->lastframe = t->frame; 936 #if defined(DEBUG) || defined(SLHCI_DEBUG) 937 if (__predict_false(spipe->ptype == PT_INTR && 938 xfer->length > spipe->tregs[LEN])) { 939 printf("%s: Long INTR transfer not supported!\n", 940 SC_NAME(sc)); 941 DDOLOG("%s: Long INTR transfer not supported!\n", 942 SC_NAME(sc), 0,0,0); 943 xfer->status = USBD_INVAL; 944 } 945 #endif 946 } else { 947 /* ptype may be currently set to any control transfer type. */ 948 SLHCI_DEXEC(D_TRACE, slhci_log_xfer(xfer)); 949 950 /* SETUP contains IN/OUT bits also */ 951 spipe->tregs[PID] |= SL11_PID_SETUP; 952 spipe->tregs[LEN] = 8; 953 spipe->buffer = (uint8_t *)&xfer->request; 954 DLOGBUF(D_XFER, spipe->buffer, spipe->tregs[LEN]); 955 spipe->ptype = PT_CTRL_SETUP; 956 spipe->newpid &= ~SL11_PID_BITS; 957 if (xfer->length == 0 || (xfer->request.bmRequestType & 958 UT_READ)) 959 spipe->newpid |= SL11_PID_IN; 960 else 961 spipe->newpid |= SL11_PID_OUT; 962 } 963 964 if (xfer->flags & USBD_FORCE_SHORT_XFER && spipe->tregs[LEN] == 965 max_packet && (spipe->newpid & SL11_PID_BITS) == SL11_PID_OUT) 966 spipe->wantshort = 1; 967 else 968 spipe->wantshort = 0; 969 970 /* The goal of newbustime and newlen is to avoid bustime calculation 971 * in the interrupt. The calculations are not too complex, but they 972 * complicate the conditional logic somewhat and doing them all in the 973 * same place shares constants. Index 0 is "short length" for bulk and 974 * ctrl data and 1 is "full length" for ctrl data (bulk/intr are 975 * already set to full length). */ 976 if (spipe->pflags & PF_LS) { 977 /* Setting PREAMBLE for directly connnected LS devices will 978 * lock up the chip. */ 979 if (spipe->pflags & PF_PREAMBLE) 980 spipe->control |= SL11_EPCTRL_PREAMBLE; 981 if (max_packet <= 8) { 982 spipe->bustime = SLHCI_LS_CONST + 983 SLHCI_LS_DATA_TIME(spipe->tregs[LEN]); 984 spipe->newbustime[0] = SLHCI_LS_CONST + 985 SLHCI_LS_DATA_TIME(spipe->newlen[0]); 986 spipe->newbustime[1] = SLHCI_LS_CONST + 987 SLHCI_LS_DATA_TIME(spipe->newlen[1]); 988 } else 989 xfer->status = USBD_INVAL; 990 } else { 991 UL_SLASSERT(pipe->device->speed == USB_SPEED_FULL, sc, 992 spipe, xfer, return USBD_IN_PROGRESS); 993 if (max_packet <= SL11_MAX_PACKET_SIZE) { 994 spipe->bustime = SLHCI_FS_CONST + 995 SLHCI_FS_DATA_TIME(spipe->tregs[LEN]); 996 spipe->newbustime[0] = SLHCI_FS_CONST + 997 SLHCI_FS_DATA_TIME(spipe->newlen[0]); 998 spipe->newbustime[1] = SLHCI_FS_CONST + 999 SLHCI_FS_DATA_TIME(spipe->newlen[1]); 1000 } else 1001 xfer->status = USBD_INVAL; 1002 } 1003 1004 /* The datasheet incorrectly indicates that DIRECTION is for 1005 * "transmit to host". It is for OUT and SETUP. The app note 1006 * describes its use correctly. */ 1007 if ((spipe->tregs[PID] & SL11_PID_BITS) != SL11_PID_IN) 1008 spipe->control |= SL11_EPCTRL_DIRECTION; 1009 1010 slhci_start_entry(sc, spipe); 1011 1012 return USBD_IN_PROGRESS; 1013 } 1014 1015 usbd_status 1016 slhci_root_start(struct usbd_xfer *xfer) 1017 { 1018 struct slhci_softc *sc; 1019 struct slhci_pipe *spipe; 1020 1021 spipe = (struct slhci_pipe *)xfer->pipe; 1022 sc = xfer->pipe->device->bus->hci_private; 1023 1024 return slhci_lock_call(sc, &slhci_root, spipe, xfer); 1025 } 1026 1027 usbd_status 1028 slhci_open(struct usbd_pipe *pipe) 1029 { 1030 struct usbd_device *dev; 1031 struct slhci_softc *sc; 1032 struct slhci_pipe *spipe; 1033 usb_endpoint_descriptor_t *ed; 1034 struct slhci_transfers *t; 1035 unsigned int max_packet, pmaxpkt; 1036 1037 dev = pipe->device; 1038 sc = dev->bus->hci_private; 1039 spipe = (struct slhci_pipe *)pipe; 1040 ed = pipe->endpoint->edesc; 1041 t = &sc->sc_transfers; 1042 1043 DLOG(D_TRACE, "slhci_open(addr=%d,ep=%d,rootaddr=%d)", 1044 dev->address, ed->bEndpointAddress, t->rootaddr, 0); 1045 1046 spipe->pflags = 0; 1047 spipe->frame = 0; 1048 spipe->lastframe = 0; 1049 spipe->xfer = NULL; 1050 spipe->buffer = NULL; 1051 1052 gcq_init(&spipe->ap); 1053 gcq_init(&spipe->to); 1054 gcq_init(&spipe->xq); 1055 1056 /* The endpoint descriptor will not have been set up yet in the case 1057 * of the standard control pipe, so the max packet checks are also 1058 * necessary in start. */ 1059 1060 max_packet = UGETW(ed->wMaxPacketSize); 1061 1062 if (dev->speed == USB_SPEED_LOW) { 1063 spipe->pflags |= PF_LS; 1064 if (dev->myhub->address != t->rootaddr) { 1065 spipe->pflags |= PF_PREAMBLE; 1066 if (!slhci_try_lsvh) 1067 return slhci_lock_call(sc, &slhci_lsvh_warn, 1068 spipe, NULL); 1069 } 1070 pmaxpkt = 8; 1071 } else 1072 pmaxpkt = SL11_MAX_PACKET_SIZE; 1073 1074 if (max_packet > pmaxpkt) { 1075 DLOG(D_ERR, "packet too large! size %d spipe %p", max_packet, 1076 spipe, 0,0); 1077 return USBD_INVAL; 1078 } 1079 1080 if (dev->address == t->rootaddr) { 1081 switch (ed->bEndpointAddress) { 1082 case USB_CONTROL_ENDPOINT: 1083 spipe->ptype = PT_ROOT_CTRL; 1084 pipe->interval = 0; 1085 break; 1086 case UE_DIR_IN | ROOT_INTR_ENDPT: 1087 spipe->ptype = PT_ROOT_INTR; 1088 pipe->interval = 1; 1089 break; 1090 default: 1091 printf("%s: Invalid root endpoint!\n", SC_NAME(sc)); 1092 DDOLOG("%s: Invalid root endpoint!\n", SC_NAME(sc), 1093 0,0,0); 1094 return USBD_INVAL; 1095 } 1096 pipe->methods = __UNCONST(&slhci_root_methods); 1097 return USBD_NORMAL_COMPLETION; 1098 } else { 1099 switch (ed->bmAttributes & UE_XFERTYPE) { 1100 case UE_CONTROL: 1101 spipe->ptype = PT_CTRL_SETUP; 1102 pipe->interval = 0; 1103 break; 1104 case UE_INTERRUPT: 1105 spipe->ptype = PT_INTR; 1106 if (pipe->interval == USBD_DEFAULT_INTERVAL) 1107 pipe->interval = ed->bInterval; 1108 break; 1109 case UE_ISOCHRONOUS: 1110 return slhci_lock_call(sc, &slhci_isoc_warn, spipe, 1111 NULL); 1112 case UE_BULK: 1113 spipe->ptype = PT_BULK; 1114 pipe->interval = 0; 1115 break; 1116 } 1117 1118 DLOG(D_MSG, "open pipe %s interval %d", pnames(spipe->ptype), 1119 pipe->interval, 0,0); 1120 1121 pipe->methods = __UNCONST(&slhci_pipe_methods); 1122 1123 return slhci_lock_call(sc, &slhci_open_pipe, spipe, NULL); 1124 } 1125 } 1126 1127 int 1128 slhci_supported_rev(uint8_t rev) 1129 { 1130 return (rev >= SLTYPE_SL811HS_R12 && rev <= SLTYPE_SL811HS_R15); 1131 } 1132 1133 /* Must be called before the ISR is registered. Interrupts can be shared so 1134 * slhci_intr could be called as soon as the ISR is registered. 1135 * Note max_current argument is actual current, but stored as current/2 */ 1136 void 1137 slhci_preinit(struct slhci_softc *sc, PowerFunc pow, bus_space_tag_t iot, 1138 bus_space_handle_t ioh, uint16_t max_current, uint8_t stride) 1139 { 1140 struct slhci_transfers *t; 1141 int i; 1142 1143 t = &sc->sc_transfers; 1144 1145 #ifdef SLHCI_DEBUG 1146 UVMHIST_INIT_STATIC(slhcihist, slhci_he); 1147 #endif 1148 simple_lock_init(&sc->sc_lock); 1149 #ifdef SLHCI_WAITLOCK 1150 simple_lock_init(&sc->sc_wait_lock); 1151 #endif 1152 /* sc->sc_ier = 0; */ 1153 /* t->rootintr = NULL; */ 1154 t->flags = F_NODEV|F_UDISABLED; 1155 t->pend = INT_MAX; 1156 KASSERT(slhci_wait_time != INT_MAX); 1157 t->len[0] = t->len[1] = -1; 1158 if (max_current > 500) 1159 max_current = 500; 1160 t->max_current = (uint8_t)(max_current / 2); 1161 sc->sc_enable_power = pow; 1162 sc->sc_iot = iot; 1163 sc->sc_ioh = ioh; 1164 sc->sc_stride = stride; 1165 1166 KASSERT(Q_MAX+1 == sizeof(t->q) / sizeof(t->q[0])); 1167 1168 for (i = 0; i <= Q_MAX; i++) 1169 gcq_init_head(&t->q[i]); 1170 gcq_init_head(&t->timed); 1171 gcq_init_head(&t->to); 1172 gcq_init_head(&t->ap); 1173 #ifdef SLHCI_WAITLOCK 1174 gcq_init_head(&sc->sc_waitq); 1175 #endif 1176 } 1177 1178 int 1179 slhci_attach(struct slhci_softc *sc) 1180 { 1181 if (slhci_lock_call(sc, &slhci_do_attach, NULL, NULL) != 1182 USBD_NORMAL_COMPLETION) 1183 return -1; 1184 1185 /* Attach usb and uhub. */ 1186 sc->sc_child = config_found(SC_DEV(sc), &sc->sc_bus, usbctlprint); 1187 1188 if (!sc->sc_child) 1189 return -1; 1190 else 1191 return 0; 1192 } 1193 1194 int 1195 slhci_detach(struct slhci_softc *sc, int flags) 1196 { 1197 struct slhci_transfers *t; 1198 int ret; 1199 1200 t = &sc->sc_transfers; 1201 1202 /* By this point bus access is no longer allowed. */ 1203 1204 KASSERT(!(t->flags & F_ACTIVE)); 1205 1206 /* To be MPSAFE is not sufficient to cancel callouts and soft 1207 * interrupts and assume they are dead since the code could already be 1208 * running or about to run. Wait until they are known to be done. */ 1209 while (t->flags & (F_RESET|F_CALLBACK)) 1210 tsleep(&sc, PPAUSE, "slhci_detach", hz); 1211 1212 softint_disestablish(sc->sc_cb_softintr); 1213 1214 ret = 0; 1215 1216 if (sc->sc_child) 1217 ret = config_detach(sc->sc_child, flags); 1218 1219 #ifdef SLHCI_MEM_ACCOUNTING 1220 if (sc->sc_mem_use) { 1221 printf("%s: Memory still in use after detach! mem_use (count)" 1222 " = %d\n", SC_NAME(sc), sc->sc_mem_use); 1223 DDOLOG("%s: Memory still in use after detach! mem_use (count)" 1224 " = %d\n", SC_NAME(sc), sc->sc_mem_use, 0,0); 1225 } 1226 #endif 1227 1228 return ret; 1229 } 1230 1231 int 1232 slhci_activate(struct device *self, enum devact act) 1233 { 1234 struct slhci_softc *sc; 1235 1236 sc = device_private(self); 1237 1238 if (act != DVACT_DEACTIVATE) 1239 return EOPNOTSUPP; 1240 1241 slhci_lock_call(sc, &slhci_halt, NULL, NULL); 1242 1243 if (sc->sc_child) 1244 return config_deactivate(sc->sc_child); 1245 else 1246 return 0; 1247 } 1248 1249 void 1250 slhci_abort(struct usbd_xfer *xfer) 1251 { 1252 struct slhci_softc *sc; 1253 struct slhci_pipe *spipe; 1254 1255 spipe = (struct slhci_pipe *)xfer->pipe; 1256 1257 if (spipe == NULL) 1258 goto callback; 1259 1260 sc = spipe->pipe.device->bus->hci_private; 1261 1262 DLOG(D_TRACE, "%s abort xfer %p spipe %p spipe->xfer %p", 1263 pnames(spipe->ptype), xfer, spipe, spipe->xfer); 1264 1265 slhci_lock_call(sc, &slhci_do_abort, spipe, xfer); 1266 1267 callback: 1268 xfer->status = USBD_CANCELLED; 1269 /* Abort happens at splsoftusb. */ 1270 usb_transfer_complete(xfer); 1271 } 1272 1273 void 1274 slhci_close(struct usbd_pipe *pipe) 1275 { 1276 struct slhci_softc *sc; 1277 struct slhci_pipe *spipe; 1278 struct slhci_transfers *t; 1279 1280 sc = pipe->device->bus->hci_private; 1281 spipe = (struct slhci_pipe *)pipe; 1282 t = &sc->sc_transfers; 1283 1284 DLOG(D_TRACE, "%s close spipe %p spipe->xfer %p", 1285 pnames(spipe->ptype), spipe, spipe->xfer, 0); 1286 1287 slhci_lock_call(sc, &slhci_close_pipe, spipe, NULL); 1288 } 1289 1290 void 1291 slhci_clear_toggle(struct usbd_pipe *pipe) 1292 { 1293 struct slhci_pipe *spipe; 1294 1295 spipe = (struct slhci_pipe *)pipe; 1296 1297 DLOG(D_TRACE, "%s toggle spipe %p", pnames(spipe->ptype), 1298 spipe,0,0); 1299 1300 spipe->pflags &= ~PF_TOGGLE; 1301 1302 #ifdef DIAGNOSTIC 1303 if (spipe->xfer != NULL) { 1304 struct slhci_softc *sc = (struct slhci_softc 1305 *)pipe->device->bus; 1306 1307 printf("%s: Clear toggle on transfer in progress! halted\n", 1308 SC_NAME(sc)); 1309 DDOLOG("%s: Clear toggle on transfer in progress! halted\n", 1310 SC_NAME(sc), 0,0,0); 1311 slhci_halt(sc, NULL, NULL); 1312 } 1313 #endif 1314 } 1315 1316 void 1317 slhci_poll(struct usbd_bus *bus) /* XXX necessary? */ 1318 { 1319 struct slhci_softc *sc; 1320 1321 sc = bus->hci_private; 1322 1323 DLOG(D_TRACE, "slhci_poll", 0,0,0,0); 1324 1325 slhci_lock_call(sc, &slhci_do_poll, NULL, NULL); 1326 } 1327 1328 void 1329 slhci_done(struct usbd_xfer *xfer) 1330 { 1331 /* xfer may not be valid here */ 1332 } 1333 1334 void 1335 slhci_void(void *v) {} 1336 1337 /* End out of lock functions. Start lock entry functions. */ 1338 1339 #ifdef SLHCI_MEM_ACCOUNTING 1340 void 1341 slhci_mem_use(struct usbd_bus *bus, int val) 1342 { 1343 struct slhci_softc *sc = bus->hci_private; 1344 int s; 1345 1346 s = splhardusb(); 1347 simple_lock(&sc->sc_wait_lock); 1348 sc->sc_mem_use += val; 1349 simple_unlock(&sc->sc_wait_lock); 1350 splx(s); 1351 } 1352 #endif 1353 1354 void 1355 slhci_reset_entry(void *arg) 1356 { 1357 struct slhci_softc *sc; 1358 int s; 1359 1360 sc = (struct slhci_softc *)arg; 1361 1362 s = splhardusb(); 1363 simple_lock(&sc->sc_lock); 1364 slhci_reset(sc); 1365 /* We cannot call the calback directly since we could then be reset 1366 * again before finishing and need the callout delay for timing. 1367 * Scheduling the callout again before we exit would defeat the reap 1368 * mechanism since we could be unlocked while the reset flag is not 1369 * set. The callback code will check the wait queue. */ 1370 slhci_callback_schedule(sc); 1371 simple_unlock(&sc->sc_lock); 1372 splx(s); 1373 } 1374 1375 usbd_status 1376 slhci_lock_call(struct slhci_softc *sc, LockCallFunc lcf, struct slhci_pipe 1377 *spipe, struct usbd_xfer *xfer) 1378 { 1379 usbd_status ret; 1380 int x, s; 1381 1382 x = splsoftusb(); 1383 s = splhardusb(); 1384 simple_lock(&sc->sc_lock); 1385 ret = (*lcf)(sc, spipe, xfer); 1386 slhci_main(sc, &s); 1387 splx(s); 1388 splx(x); 1389 1390 return ret; 1391 } 1392 1393 void 1394 slhci_start_entry(struct slhci_softc *sc, struct slhci_pipe *spipe) 1395 { 1396 struct slhci_transfers *t; 1397 int s; 1398 1399 t = &sc->sc_transfers; 1400 1401 s = splhardusb(); 1402 #ifdef SLHCI_WAITLOCK 1403 if (simple_lock_try(&sc->sc_lock)) 1404 #else 1405 simple_lock(&sc->sc_lock); 1406 #endif 1407 { 1408 slhci_enter_xfer(sc, spipe); 1409 slhci_dotransfer(sc); 1410 slhci_main(sc, &s); 1411 #ifdef SLHCI_WAITLOCK 1412 } else { 1413 simple_lock(&sc->sc_wait_lock); 1414 enter_waitq(sc, spipe); 1415 simple_unlock(&sc->sc_wait_lock); 1416 #endif 1417 } 1418 splx(s); 1419 } 1420 1421 void 1422 slhci_callback_entry(void *arg) 1423 { 1424 struct slhci_softc *sc; 1425 struct slhci_transfers *t; 1426 int s, x; 1427 1428 1429 sc = (struct slhci_softc *)arg; 1430 1431 x = splsoftusb(); 1432 s = splhardusb(); 1433 simple_lock(&sc->sc_lock); 1434 t = &sc->sc_transfers; 1435 DLOG(D_SOFT, "callback_entry flags %#x", t->flags, 0,0,0); 1436 1437 #ifdef SLHCI_WAITLOCK 1438 repeat: 1439 #endif 1440 slhci_callback(sc, &s); 1441 1442 #ifdef SLHCI_WAITLOCK 1443 simple_lock(&sc->sc_wait_lock); 1444 if (!gcq_empty(&sc->sc_waitq)) { 1445 slhci_enter_xfers(sc); 1446 simple_unlock(&sc->sc_wait_lock); 1447 slhci_dotransfer(sc); 1448 slhci_waitintr(sc, 0); 1449 goto repeat; 1450 } 1451 1452 t->flags &= ~F_CALLBACK; 1453 simple_unlock(&sc->sc_lock); 1454 simple_unlock(&sc->sc_wait_lock); 1455 #else 1456 t->flags &= ~F_CALLBACK; 1457 simple_unlock(&sc->sc_lock); 1458 #endif 1459 splx(s); 1460 splx(x); 1461 } 1462 1463 void 1464 slhci_do_callback(struct slhci_softc *sc, struct usbd_xfer *xfer, int *s) 1465 { 1466 SLHCI_LOCKASSERT(sc, locked, unlocked); 1467 1468 int repeat; 1469 1470 sc->sc_bus.intr_context++; 1471 start_cc_time(&t_callback, (u_int)xfer); 1472 simple_unlock(&sc->sc_lock); 1473 splx(*s); 1474 1475 repeat = xfer->pipe->repeat; 1476 1477 usb_transfer_complete(xfer); 1478 1479 *s = splhardusb(); 1480 simple_lock(&sc->sc_lock); 1481 stop_cc_time(&t_callback); 1482 sc->sc_bus.intr_context--; 1483 1484 if (repeat && !sc->sc_bus.use_polling) 1485 slhci_do_repeat(sc, xfer); 1486 } 1487 1488 int 1489 slhci_intr(void *arg) 1490 { 1491 struct slhci_softc *sc; 1492 int ret; 1493 1494 sc = (struct slhci_softc *)arg; 1495 1496 start_cc_time(&t_hard_int, (unsigned int)arg); 1497 simple_lock(&sc->sc_lock); 1498 1499 ret = slhci_dointr(sc); 1500 slhci_main(sc, NULL); 1501 1502 stop_cc_time(&t_hard_int); 1503 return ret; 1504 } 1505 1506 /* called with main lock only held, returns with locks released. */ 1507 void 1508 slhci_main(struct slhci_softc *sc, int *s) 1509 { 1510 struct slhci_transfers *t; 1511 1512 t = &sc->sc_transfers; 1513 1514 SLHCI_LOCKASSERT(sc, locked, unlocked); 1515 1516 #ifdef SLHCI_WAITLOCK 1517 waitcheck: 1518 #endif 1519 slhci_waitintr(sc, slhci_wait_time); 1520 1521 1522 /* 1523 * XXX Directly calling the callback anytime s != NULL 1524 * causes panic:sbdrop with aue (simultaneously using umass). 1525 * Doing that affects process accounting, but is supposed to work as 1526 * far as I can tell. 1527 * 1528 * The direct call is needed in the use_polling and disabled cases 1529 * since the soft interrupt is not available. In the disabled case, 1530 * this code can be reached from the usb detach, after the reaping of 1531 * the soft interrupt. That test could be !F_ACTIVE (in which case 1532 * s != NULL could be an assertion), but there is no reason not to 1533 * make the callbacks directly in the other DISABLED cases. 1534 */ 1535 if ((t->flags & F_ROOTINTR) || !gcq_empty(&t->q[Q_CALLBACKS])) { 1536 if (__predict_false(sc->sc_bus.use_polling || t->flags & 1537 F_DISABLED) && s != NULL) 1538 slhci_callback(sc, s); 1539 else 1540 slhci_callback_schedule(sc); 1541 } 1542 1543 #ifdef SLHCI_WAITLOCK 1544 simple_lock(&sc->sc_wait_lock); 1545 1546 if (!gcq_empty(&sc->sc_waitq)) { 1547 slhci_enter_xfers(sc); 1548 simple_unlock(&sc->sc_wait_lock); 1549 slhci_dotransfer(sc); 1550 goto waitcheck; 1551 } 1552 1553 simple_unlock(&sc->sc_lock); 1554 simple_unlock(&sc->sc_wait_lock); 1555 #else 1556 simple_unlock(&sc->sc_lock); 1557 #endif 1558 } 1559 1560 /* End lock entry functions. Start in lock function. */ 1561 1562 /* Register read/write routines and barriers. */ 1563 #ifdef SLHCI_BUS_SPACE_BARRIERS 1564 #define BSB(a, b, c, d, e) bus_space_barrier(a, b, c, d, BUS_SPACE_BARRIER_ # e) 1565 #define BSB_SYNC(a, b, c, d) bus_space_barrier(a, b, c, d, BUS_SPACE_BARRIER_SYNC) 1566 #else /* now !SLHCI_BUS_SPACE_BARRIERS */ 1567 #define BSB(a, b, c, d, e) 1568 #define BSB_SYNC(a, b, c, d) 1569 #endif /* SLHCI_BUS_SPACE_BARRIERS */ 1570 1571 static void 1572 slhci_write(struct slhci_softc *sc, uint8_t addr, uint8_t data) 1573 { 1574 bus_size_t paddr, pdata, pst, psz; 1575 bus_space_tag_t iot; 1576 bus_space_handle_t ioh; 1577 1578 paddr = pst = 0; 1579 pdata = sc->sc_stride; 1580 psz = pdata * 2; 1581 iot = sc->sc_iot; 1582 ioh = sc->sc_ioh; 1583 1584 bus_space_write_1(iot, ioh, paddr, addr); 1585 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1586 bus_space_write_1(iot, ioh, pdata, data); 1587 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1588 } 1589 1590 static uint8_t 1591 slhci_read(struct slhci_softc *sc, uint8_t addr) 1592 { 1593 bus_size_t paddr, pdata, pst, psz; 1594 bus_space_tag_t iot; 1595 bus_space_handle_t ioh; 1596 uint8_t data; 1597 1598 paddr = pst = 0; 1599 pdata = sc->sc_stride; 1600 psz = pdata * 2; 1601 iot = sc->sc_iot; 1602 ioh = sc->sc_ioh; 1603 1604 bus_space_write_1(iot, ioh, paddr, addr); 1605 BSB(iot, ioh, pst, psz, WRITE_BEFORE_READ); 1606 data = bus_space_read_1(iot, ioh, pdata); 1607 BSB(iot, ioh, pst, psz, READ_BEFORE_WRITE); 1608 return data; 1609 } 1610 1611 #if 0 /* auto-increment mode broken, see errata doc */ 1612 static void 1613 slhci_write_multi(struct slhci_softc *sc, uint8_t addr, uint8_t *buf, int l) 1614 { 1615 bus_size_t paddr, pdata, pst, psz; 1616 bus_space_tag_t iot; 1617 bus_space_handle_t ioh; 1618 1619 paddr = pst = 0; 1620 pdata = sc->sc_stride; 1621 psz = pdata * 2; 1622 iot = sc->sc_iot; 1623 ioh = sc->sc_ioh; 1624 1625 bus_space_write_1(iot, ioh, paddr, addr); 1626 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1627 bus_space_write_multi_1(iot, ioh, pdata, buf, l); 1628 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1629 } 1630 1631 static void 1632 slhci_read_multi(struct slhci_softc *sc, uint8_t addr, uint8_t *buf, int l) 1633 { 1634 bus_size_t paddr, pdata, pst, psz; 1635 bus_space_tag_t iot; 1636 bus_space_handle_t ioh; 1637 1638 paddr = pst = 0; 1639 pdata = sc->sc_stride; 1640 psz = pdata * 2; 1641 iot = sc->sc_iot; 1642 ioh = sc->sc_ioh; 1643 1644 bus_space_write_1(iot, ioh, paddr, addr); 1645 BSB(iot, ioh, pst, psz, WRITE_BEFORE_READ); 1646 bus_space_read_multi_1(iot, ioh, pdata, buf, l); 1647 BSB(iot, ioh, pst, psz, READ_BEFORE_WRITE); 1648 } 1649 #else 1650 static void 1651 slhci_write_multi(struct slhci_softc *sc, uint8_t addr, uint8_t *buf, int l) 1652 { 1653 #if 1 1654 for (; l; addr++, buf++, l--) 1655 slhci_write(sc, addr, *buf); 1656 #else 1657 bus_size_t paddr, pdata, pst, psz; 1658 bus_space_tag_t iot; 1659 bus_space_handle_t ioh; 1660 1661 paddr = pst = 0; 1662 pdata = sc->sc_stride; 1663 psz = pdata * 2; 1664 iot = sc->sc_iot; 1665 ioh = sc->sc_ioh; 1666 1667 for (; l; addr++, buf++, l--) { 1668 bus_space_write_1(iot, ioh, paddr, addr); 1669 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1670 bus_space_write_1(iot, ioh, pdata, *buf); 1671 BSB(iot, ioh, pst, psz, WRITE_BEFORE_WRITE); 1672 } 1673 #endif 1674 } 1675 1676 static void 1677 slhci_read_multi(struct slhci_softc *sc, uint8_t addr, uint8_t *buf, int l) 1678 { 1679 #if 1 1680 for (; l; addr++, buf++, l--) 1681 *buf = slhci_read(sc, addr); 1682 #else 1683 bus_size_t paddr, pdata, pst, psz; 1684 bus_space_tag_t iot; 1685 bus_space_handle_t ioh; 1686 1687 paddr = pst = 0; 1688 pdata = sc->sc_stride; 1689 psz = pdata * 2; 1690 iot = sc->sc_iot; 1691 ioh = sc->sc_ioh; 1692 1693 for (; l; addr++, buf++, l--) { 1694 bus_space_write_1(iot, ioh, paddr, addr); 1695 BSB(iot, ioh, pst, psz, WRITE_BEFORE_READ); 1696 *buf = bus_space_read_1(iot, ioh, pdata); 1697 BSB(iot, ioh, pst, psz, READ_BEFORE_WRITE); 1698 } 1699 #endif 1700 } 1701 #endif 1702 1703 /* After calling waitintr it is necessary to either call slhci_callback or 1704 * schedule the callback if necessary. The callback cannot be called directly 1705 * from the hard interrupt since it interrupts at a high IPL and callbacks 1706 * can do copyout and such. */ 1707 static void 1708 slhci_waitintr(struct slhci_softc *sc, int wait_time) 1709 { 1710 struct slhci_transfers *t; 1711 1712 t = &sc->sc_transfers; 1713 1714 SLHCI_LOCKASSERT(sc, locked, unlocked); 1715 1716 if (__predict_false(sc->sc_bus.use_polling)) 1717 wait_time = 12000; 1718 1719 while (t->pend <= wait_time) { 1720 DLOG(D_WAIT, "waiting... frame %d pend %d flags %#x", 1721 t->frame, t->pend, t->flags, 0); 1722 LK_SLASSERT(t->flags & F_ACTIVE, sc, NULL, NULL, return); 1723 LK_SLASSERT(t->flags & (F_AINPROG|F_BINPROG), sc, NULL, NULL, 1724 return); 1725 slhci_dointr(sc); 1726 } 1727 } 1728 1729 static int 1730 slhci_dointr(struct slhci_softc *sc) 1731 { 1732 struct slhci_transfers *t; 1733 struct slhci_pipe *tosp; 1734 uint8_t r; 1735 1736 t = &sc->sc_transfers; 1737 1738 SLHCI_LOCKASSERT(sc, locked, unlocked); 1739 1740 if (sc->sc_ier == 0) 1741 return 0; 1742 1743 r = slhci_read(sc, SL11_ISR); 1744 1745 #ifdef SLHCI_DEBUG 1746 if (slhci_debug & SLHCI_D_INTR && r & sc->sc_ier && 1747 ((r & ~(SL11_ISR_SOF|SL11_ISR_DATA)) || slhci_debug & 1748 SLHCI_D_SOF)) { 1749 uint8_t e, f; 1750 1751 e = slhci_read(sc, SL11_IER); 1752 f = slhci_read(sc, SL11_CTRL); 1753 DDOLOG("Flags=%#x IER=%#x ISR=%#x", t->flags, e, r, 0); 1754 DDOLOGFLAG8("Status=", r, "D+", (f & SL11_CTRL_SUSPEND) ? 1755 "RESUME" : "NODEV", "INSERT", "SOF", "res", "BABBLE", 1756 "USBB", "USBA"); 1757 } 1758 #endif 1759 1760 /* check IER for corruption occasionally. Assume that the above 1761 * sc_ier == 0 case works correctly. */ 1762 if (__predict_false(sc->sc_ier_check++ > SLHCI_IER_CHECK_FREQUENCY)) { 1763 sc->sc_ier_check = 0; 1764 if (sc->sc_ier != slhci_read(sc, SL11_IER)) { 1765 printf("%s: IER value corrupted! halted\n", 1766 SC_NAME(sc)); 1767 DDOLOG("%s: IER value corrupted! halted\n", 1768 SC_NAME(sc), 0,0,0); 1769 slhci_halt(sc, NULL, NULL); 1770 return 1; 1771 } 1772 } 1773 1774 r &= sc->sc_ier; 1775 1776 if (r == 0) 1777 return 0; 1778 1779 sc->sc_ier_check = 0; 1780 1781 slhci_write(sc, SL11_ISR, r); 1782 BSB_SYNC(sc->iot, sc->ioh, sc->pst, sc->psz); 1783 1784 1785 /* If we have an insertion event we do not care about anything else. */ 1786 if (__predict_false(r & SL11_ISR_INSERT)) { 1787 slhci_insert(sc); 1788 return 1; 1789 } 1790 1791 stop_cc_time(&t_intr); 1792 start_cc_time(&t_intr, r); 1793 1794 if (r & SL11_ISR_SOF) { 1795 t->frame++; 1796 1797 gcq_merge_tail(&t->q[Q_CB], &t->q[Q_NEXT_CB]); 1798 1799 /* SOFCHECK flags are cleared in tstart. Two flags are needed 1800 * since the first SOF interrupt processed after the transfer 1801 * is started might have been generated before the transfer 1802 * was started. */ 1803 if (__predict_false(t->flags & F_SOFCHECK2 && t->flags & 1804 (F_AINPROG|F_BINPROG))) { 1805 printf("%s: Missed transfer completion. halted\n", 1806 SC_NAME(sc)); 1807 DDOLOG("%s: Missed transfer completion. halted\n", 1808 SC_NAME(sc), 0,0,0); 1809 slhci_halt(sc, NULL, NULL); 1810 return 1; 1811 } else if (t->flags & F_SOFCHECK1) { 1812 t->flags |= F_SOFCHECK2; 1813 } else 1814 t->flags |= F_SOFCHECK1; 1815 1816 if (t->flags & F_CHANGE) 1817 t->flags |= F_ROOTINTR; 1818 1819 while (__predict_true(GOT_FIRST_TO(tosp, t)) && 1820 __predict_false(tosp->to_frame <= t->frame)) { 1821 tosp->xfer->status = USBD_TIMEOUT; 1822 slhci_do_abort(sc, tosp, tosp->xfer); 1823 enter_callback(t, tosp); 1824 } 1825 1826 /* Start any waiting transfers right away. If none, we will 1827 * start any new transfers later. */ 1828 slhci_tstart(sc); 1829 } 1830 1831 if (r & (SL11_ISR_USBA|SL11_ISR_USBB)) { 1832 int ab; 1833 1834 if ((r & (SL11_ISR_USBA|SL11_ISR_USBB)) == 1835 (SL11_ISR_USBA|SL11_ISR_USBB)) { 1836 if (!(t->flags & (F_AINPROG|F_BINPROG))) 1837 return 1; /* presume card pulled */ 1838 1839 LK_SLASSERT((t->flags & (F_AINPROG|F_BINPROG)) != 1840 (F_AINPROG|F_BINPROG), sc, NULL, NULL, return 1); 1841 1842 /* This should never happen (unless card removal just 1843 * occurred) but appeared frequently when both 1844 * transfers were started at the same time and was 1845 * accompanied by data corruption. It still happens 1846 * at times. I have not seen data correption except 1847 * when the STATUS bit gets set, which now causes the 1848 * driver to halt, however this should still not 1849 * happen so the warning is kept. See comment in 1850 * abdone, below. 1851 */ 1852 printf("%s: Transfer reported done but not started! " 1853 "Verify data integrity if not detaching. " 1854 " flags %#x r %x\n", SC_NAME(sc), t->flags, r); 1855 1856 if (!(t->flags & F_AINPROG)) 1857 r &= ~SL11_ISR_USBA; 1858 else 1859 r &= ~SL11_ISR_USBB; 1860 } 1861 t->pend = INT_MAX; 1862 1863 if (r & SL11_ISR_USBA) 1864 ab = A; 1865 else 1866 ab = B; 1867 1868 /* This happens when a low speed device is attached to 1869 * a hub with chip rev 1.5. SOF stops, but a few transfers 1870 * still work before causing this error. 1871 */ 1872 if (!(t->flags & (ab ? F_BINPROG : F_AINPROG))) { 1873 printf("%s: %s done but not in progress! halted\n", 1874 SC_NAME(sc), ab ? "B" : "A"); 1875 DDOLOG("%s: %s done but not in progress! halted\n", 1876 SC_NAME(sc), ab ? "B" : "A", 0,0); 1877 slhci_halt(sc, NULL, NULL); 1878 return 1; 1879 } 1880 1881 t->flags &= ~(ab ? F_BINPROG : F_AINPROG); 1882 slhci_tstart(sc); 1883 stop_cc_time(&t_ab[ab]); 1884 start_cc_time(&t_abdone, t->flags); 1885 slhci_abdone(sc, ab); 1886 stop_cc_time(&t_abdone); 1887 } 1888 1889 slhci_dotransfer(sc); 1890 1891 return 1; 1892 } 1893 1894 static void 1895 slhci_abdone(struct slhci_softc *sc, int ab) 1896 { 1897 struct slhci_transfers *t; 1898 struct slhci_pipe *spipe; 1899 struct usbd_xfer *xfer; 1900 uint8_t status, buf_start; 1901 uint8_t *target_buf; 1902 unsigned int actlen; 1903 int head; 1904 1905 t = &sc->sc_transfers; 1906 1907 SLHCI_LOCKASSERT(sc, locked, unlocked); 1908 1909 DLOG(D_TRACE, "ABDONE flags %#x", t->flags, 0,0,0); 1910 1911 DLOG(D_MSG, "DONE %s spipe %p len %d xfer %p", ab ? "B" : "A", 1912 t->spipe[ab], t->len[ab], t->spipe[ab] ? 1913 t->spipe[ab]->xfer : NULL); 1914 1915 spipe = t->spipe[ab]; 1916 1917 /* skip this one if aborted; do not call return from the rest of the 1918 * function unless halting, else t->len will not be cleared. */ 1919 if (spipe == NULL) 1920 goto done; 1921 1922 t->spipe[ab] = NULL; 1923 1924 xfer = spipe->xfer; 1925 1926 gcq_remove(&spipe->to); 1927 1928 LK_SLASSERT(xfer != NULL, sc, spipe, NULL, return); 1929 1930 status = slhci_read(sc, slhci_tregs[ab][STAT]); 1931 1932 /* 1933 * I saw no status or remaining length greater than the requested 1934 * length in early driver versions in circumstances I assumed caused 1935 * excess power draw. I am no longer able to reproduce this when 1936 * causing excess power draw circumstances. 1937 * 1938 * Disabling a power check and attaching aue to a keyboard and hub 1939 * that is directly attached (to CFU1U, 100mA max, aue 160mA, keyboard 1940 * 98mA) sometimes works and sometimes fails to configure. After 1941 * removing the aue and attaching a self-powered umass dvd reader 1942 * (unknown if it draws power from the host also) soon a single Error 1943 * status occurs then only timeouts. The controller soon halts freeing 1944 * memory due to being ONQU instead of BUSY. This may be the same 1945 * basic sequence that caused the no status/bad length errors. The 1946 * umass device seems to work (better at least) with the keyboard hub 1947 * when not first attaching aue (tested once reading an approximately 1948 * 200MB file). 1949 * 1950 * Overflow can indicate that the device and host disagree about how 1951 * much data has been transfered. This may indicate a problem at any 1952 * point during the transfer, not just when the error occurs. It may 1953 * indicate data corruption. A warning message is printed. 1954 * 1955 * Trying to use both A and B transfers at the same time results in 1956 * incorrect transfer completion ISR reports and the status will then 1957 * include SL11_EPSTAT_SETUP, which is apparently set while the 1958 * transfer is in progress. I also noticed data corruption, even 1959 * after waiting for the transfer to complete. The driver now avoids 1960 * trying to start both at the same time. 1961 * 1962 * I had accidently initialized the B registers before they were valid 1963 * in some driver versions. Since every other performance enhancing 1964 * feature has been confirmed buggy in the errata doc, I have not 1965 * tried both transfers at once again with the documented 1966 * initialization order. 1967 * 1968 * However, I have seen this problem again ("done but not started" 1969 * errors), which in some cases cases the SETUP status bit to remain 1970 * set on future transfers. In other cases, the SETUP bit is not set 1971 * and no data corruption occurs. This occured while using both umass 1972 * and aue on a powered hub (maybe triggered by some local activity 1973 * also) and needs several reads of the 200MB file to trigger. The 1974 * driver now halts if SETUP is detected. 1975 */ 1976 1977 actlen = 0; 1978 1979 if (__predict_false(!status)) { 1980 DDOLOG("no status! xfer %p spipe %p", xfer, spipe, 0,0); 1981 printf("%s: no status! halted\n", SC_NAME(sc)); 1982 slhci_halt(sc, spipe, xfer); 1983 return; 1984 } 1985 1986 #ifdef SLHCI_DEBUG 1987 if (slhci_debug & SLHCI_D_NAK || (status & SL11_EPSTAT_ERRBITS) != 1988 SL11_EPSTAT_NAK) 1989 DLOGFLAG8(D_XFER, "STATUS=", status, "STALL", "NAK", 1990 "Overflow", "Setup", "Data Toggle", "Timeout", "Error", 1991 "ACK"); 1992 #endif 1993 1994 if (!(status & SL11_EPSTAT_ERRBITS)) { 1995 unsigned int cont; 1996 cont = slhci_read(sc, slhci_tregs[ab][CONT]); 1997 if (cont != 0) 1998 DLOG(D_XFER, "cont %d len %d", cont, 1999 spipe->tregs[LEN], 0,0); 2000 if (__predict_false(cont > spipe->tregs[LEN])) { 2001 DDOLOG("cont > len! cont %d len %d xfer->length %d " 2002 "spipe %p", cont, spipe->tregs[LEN], xfer->length, 2003 spipe); 2004 printf("%s: cont > len! cont %d len %d xfer->length " 2005 "%d", SC_NAME(sc), cont, spipe->tregs[LEN], 2006 xfer->length); 2007 slhci_halt(sc, spipe, xfer); 2008 return; 2009 } else { 2010 spipe->nerrs = 0; 2011 actlen = spipe->tregs[LEN] - cont; 2012 } 2013 } 2014 2015 /* Actual copyin done after starting next transfer. */ 2016 if (actlen && (spipe->tregs[PID] & SL11_PID_BITS) == SL11_PID_IN) { 2017 target_buf = spipe->buffer; 2018 buf_start = spipe->tregs[ADR]; 2019 } else { 2020 target_buf = NULL; 2021 buf_start = 0; /* XXX gcc uninitialized warnings */ 2022 } 2023 2024 if (status & SL11_EPSTAT_ERRBITS) { 2025 status &= SL11_EPSTAT_ERRBITS; 2026 if (status & SL11_EPSTAT_SETUP) { 2027 printf("%s: Invalid controller state detected! " 2028 "halted\n", SC_NAME(sc)); 2029 DDOLOG("%s: Invalid controller state detected! " 2030 "halted\n", SC_NAME(sc), 0,0,0); 2031 slhci_halt(sc, spipe, xfer); 2032 return; 2033 } else if (__predict_false(sc->sc_bus.use_polling)) { 2034 if (status == SL11_EPSTAT_STALL) 2035 xfer->status = USBD_STALLED; 2036 else if (status == SL11_EPSTAT_TIMEOUT) 2037 xfer->status = USBD_TIMEOUT; 2038 else if (status == SL11_EPSTAT_NAK) 2039 xfer->status = USBD_TIMEOUT; /*XXX*/ 2040 else 2041 xfer->status = USBD_IOERROR; 2042 head = Q_CALLBACKS; 2043 } else if (status == SL11_EPSTAT_NAK) { 2044 if (spipe->pipe.interval) { 2045 spipe->lastframe = spipe->frame = 2046 t->frame + spipe->pipe.interval; 2047 slhci_queue_timed(sc, spipe); 2048 goto queued; 2049 } 2050 head = Q_NEXT_CB; 2051 } else if (++spipe->nerrs > SLHCI_MAX_RETRIES || 2052 status == SL11_EPSTAT_STALL) { 2053 if (status == SL11_EPSTAT_STALL) 2054 xfer->status = USBD_STALLED; 2055 else if (status == SL11_EPSTAT_TIMEOUT) 2056 xfer->status = USBD_TIMEOUT; 2057 else 2058 xfer->status = USBD_IOERROR; 2059 2060 DLOG(D_ERR, "Max retries reached! status %#x " 2061 "xfer->status %#x", status, xfer->status, 0,0); 2062 DLOGFLAG8(D_ERR, "STATUS=", status, "STALL", 2063 "NAK", "Overflow", "Setup", "Data Toggle", 2064 "Timeout", "Error", "ACK"); 2065 2066 if (status == SL11_EPSTAT_OVERFLOW && 2067 ratecheck(&sc->sc_overflow_warn_rate, 2068 &overflow_warn_rate)) { 2069 printf("%s: Overflow condition: " 2070 "data corruption possible\n", 2071 SC_NAME(sc)); 2072 DDOLOG("%s: Overflow condition: " 2073 "data corruption possible\n", 2074 SC_NAME(sc), 0,0,0); 2075 } 2076 head = Q_CALLBACKS; 2077 } else { 2078 head = Q_NEXT_CB; 2079 } 2080 } else if (spipe->ptype == PT_CTRL_SETUP) { 2081 spipe->tregs[PID] = spipe->newpid; 2082 2083 if (xfer->length) { 2084 LK_SLASSERT(spipe->newlen[1] != 0, sc, spipe, xfer, 2085 return); 2086 spipe->tregs[LEN] = spipe->newlen[1]; 2087 spipe->bustime = spipe->newbustime[1]; 2088 spipe->buffer = KERNADDR(&xfer->dmabuf, 0); 2089 spipe->ptype = PT_CTRL_DATA; 2090 } else { 2091 status_setup: 2092 /* CTRL_DATA swaps direction in PID then jumps here */ 2093 spipe->tregs[LEN] = 0; 2094 if (spipe->pflags & PF_LS) 2095 spipe->bustime = SLHCI_LS_CONST; 2096 else 2097 spipe->bustime = SLHCI_FS_CONST; 2098 spipe->ptype = PT_CTRL_STATUS; 2099 spipe->buffer = NULL; 2100 } 2101 2102 /* Status or first data packet must be DATA1. */ 2103 spipe->control |= SL11_EPCTRL_DATATOGGLE; 2104 if ((spipe->tregs[PID] & SL11_PID_BITS) == SL11_PID_IN) 2105 spipe->control &= ~SL11_EPCTRL_DIRECTION; 2106 else 2107 spipe->control |= SL11_EPCTRL_DIRECTION; 2108 2109 head = Q_CB; 2110 } else if (spipe->ptype == PT_CTRL_STATUS) { 2111 head = Q_CALLBACKS; 2112 } else { /* bulk, intr, control data */ 2113 xfer->actlen += actlen; 2114 spipe->control ^= SL11_EPCTRL_DATATOGGLE; 2115 2116 if (actlen == spipe->tregs[LEN] && (xfer->length > 2117 xfer->actlen || spipe->wantshort)) { 2118 spipe->buffer += actlen; 2119 LK_SLASSERT(xfer->length >= xfer->actlen, sc, 2120 spipe, xfer, return); 2121 if (xfer->length - xfer->actlen < actlen) { 2122 spipe->wantshort = 0; 2123 spipe->tregs[LEN] = spipe->newlen[0]; 2124 spipe->bustime = spipe->newbustime[0]; 2125 LK_SLASSERT(xfer->actlen + 2126 spipe->tregs[LEN] == xfer->length, sc, 2127 spipe, xfer, return); 2128 } 2129 head = Q_CB; 2130 } else if (spipe->ptype == PT_CTRL_DATA) { 2131 spipe->tregs[PID] ^= SLHCI_PID_SWAP_IN_OUT; 2132 goto status_setup; 2133 } else { 2134 if (spipe->ptype == PT_INTR) { 2135 spipe->lastframe += 2136 spipe->pipe.interval; 2137 /* If ack, we try to keep the 2138 * interrupt rate by using lastframe 2139 * instead of the current frame. */ 2140 spipe->frame = spipe->lastframe + 2141 spipe->pipe.interval; 2142 } 2143 2144 /* Set the toggle for the next transfer. It 2145 * has already been toggled above, so the 2146 * current setting will apply to the next 2147 * transfer. */ 2148 if (spipe->control & SL11_EPCTRL_DATATOGGLE) 2149 spipe->pflags |= PF_TOGGLE; 2150 else 2151 spipe->pflags &= ~PF_TOGGLE; 2152 2153 head = Q_CALLBACKS; 2154 } 2155 } 2156 2157 if (head == Q_CALLBACKS) { 2158 gcq_remove(&spipe->to); 2159 2160 if (xfer->status == USBD_IN_PROGRESS) { 2161 LK_SLASSERT(xfer->actlen <= xfer->length, sc, 2162 spipe, xfer, return); 2163 xfer->status = USBD_NORMAL_COMPLETION; 2164 #if 0 /* usb_transfer_complete will do this */ 2165 if (xfer->length == xfer->actlen || xfer->flags & 2166 USBD_SHORT_XFER_OK) 2167 xfer->status = USBD_NORMAL_COMPLETION; 2168 else 2169 xfer->status = USBD_SHORT_XFER; 2170 #endif 2171 } 2172 } 2173 2174 enter_q(t, spipe, head); 2175 2176 queued: 2177 if (target_buf != NULL) { 2178 slhci_dotransfer(sc); 2179 start_cc_time(&t_copy_from_dev, actlen); 2180 slhci_read_multi(sc, buf_start, target_buf, actlen); 2181 stop_cc_time(&t_copy_from_dev); 2182 DLOGBUF(D_BUF, target_buf, actlen); 2183 t->pend -= SLHCI_FS_CONST + SLHCI_FS_DATA_TIME(actlen); 2184 } 2185 2186 done: 2187 t->len[ab] = -1; 2188 } 2189 2190 static void 2191 slhci_tstart(struct slhci_softc *sc) 2192 { 2193 struct slhci_transfers *t; 2194 struct slhci_pipe *spipe; 2195 int remaining_bustime; 2196 int s; 2197 2198 t = &sc->sc_transfers; 2199 2200 SLHCI_LOCKASSERT(sc, locked, unlocked); 2201 2202 if (!(t->flags & (F_AREADY|F_BREADY))) 2203 return; 2204 2205 if (t->flags & (F_AINPROG|F_BINPROG|F_DISABLED)) 2206 return; 2207 2208 /* We have about 6 us to get from the bus time check to 2209 * starting the transfer or we might babble or the chip might fail to 2210 * signal transfer complete. This leaves no time for any other 2211 * interrupts. Some ports have splipi (MP only) higher than splhigh 2212 * which might cause longer delays. */ 2213 s = splhigh(); 2214 remaining_bustime = (int)(slhci_read(sc, SL811_CSOF)) << 6; 2215 remaining_bustime -= SLHCI_END_BUSTIME; 2216 2217 /* Start one transfer only, clearing any aborted transfers that are 2218 * not yet in progress and skipping missed isoc. It is easier to copy 2219 * & paste most of the A/B sections than to make the logic work 2220 * otherwise and this allows better constant use. */ 2221 if (t->flags & F_AREADY) { 2222 spipe = t->spipe[A]; 2223 if (spipe == NULL) { 2224 t->flags &= ~F_AREADY; 2225 t->len[A] = -1; 2226 } else if (remaining_bustime >= spipe->bustime) { 2227 t->flags &= ~(F_AREADY|F_SOFCHECK1|F_SOFCHECK2); 2228 t->flags |= F_AINPROG; 2229 start_cc_time(&t_ab[A], spipe->tregs[LEN]); 2230 slhci_write(sc, SL11_E0CTRL, spipe->control); 2231 goto pend; 2232 } 2233 } 2234 if (t->flags & F_BREADY) { 2235 spipe = t->spipe[B]; 2236 if (spipe == NULL) { 2237 t->flags &= ~F_BREADY; 2238 t->len[B] = -1; 2239 } else if (remaining_bustime >= spipe->bustime) { 2240 t->flags &= ~(F_BREADY|F_SOFCHECK1|F_SOFCHECK2); 2241 t->flags |= F_BINPROG; 2242 start_cc_time(&t_ab[B], spipe->tregs[LEN]); 2243 slhci_write(sc, SL11_E1CTRL, spipe->control); 2244 pend: 2245 t->pend = spipe->bustime; 2246 } 2247 } 2248 splx(s); 2249 } 2250 2251 static void 2252 slhci_dotransfer(struct slhci_softc *sc) 2253 { 2254 struct slhci_transfers *t; 2255 struct slhci_pipe *spipe; 2256 int ab, i; 2257 2258 t = &sc->sc_transfers; 2259 2260 SLHCI_LOCKASSERT(sc, locked, unlocked); 2261 2262 while ((t->len[A] == -1 || t->len[B] == -1) && 2263 (GOT_FIRST_TIMED_COND(spipe, t, spipe->frame <= t->frame) || 2264 GOT_FIRST_CB(spipe, t))) { 2265 LK_SLASSERT(spipe->xfer != NULL, sc, spipe, NULL, return); 2266 LK_SLASSERT(spipe->ptype != PT_ROOT_CTRL && spipe->ptype != 2267 PT_ROOT_INTR, sc, spipe, NULL, return); 2268 2269 /* Check that this transfer can fit in the remaining memory. */ 2270 if (t->len[A] + t->len[B] + spipe->tregs[LEN] + 1 > 2271 SL11_MAX_PACKET_SIZE) { 2272 DLOG(D_XFER, "Transfer does not fit. alen %d blen %d " 2273 "len %d", t->len[A], t->len[B], spipe->tregs[LEN], 2274 0); 2275 return; 2276 } 2277 2278 gcq_remove(&spipe->xq); 2279 2280 if (t->len[A] == -1) { 2281 ab = A; 2282 spipe->tregs[ADR] = SL11_BUFFER_START; 2283 } else { 2284 ab = B; 2285 spipe->tregs[ADR] = SL11_BUFFER_END - 2286 spipe->tregs[LEN]; 2287 } 2288 2289 t->len[ab] = spipe->tregs[LEN]; 2290 2291 if (spipe->tregs[LEN] && (spipe->tregs[PID] & SL11_PID_BITS) 2292 != SL11_PID_IN) { 2293 start_cc_time(&t_copy_to_dev, 2294 spipe->tregs[LEN]); 2295 slhci_write_multi(sc, spipe->tregs[ADR], 2296 spipe->buffer, spipe->tregs[LEN]); 2297 stop_cc_time(&t_copy_to_dev); 2298 t->pend -= SLHCI_FS_CONST + 2299 SLHCI_FS_DATA_TIME(spipe->tregs[LEN]); 2300 } 2301 2302 DLOG(D_MSG, "NEW TRANSFER %s flags %#x alen %d blen %d", 2303 ab ? "B" : "A", t->flags, t->len[0], t->len[1]); 2304 2305 if (spipe->tregs[LEN]) 2306 i = 0; 2307 else 2308 i = 1; 2309 2310 for (; i <= 3; i++) 2311 if (t->current_tregs[ab][i] != spipe->tregs[i]) { 2312 t->current_tregs[ab][i] = spipe->tregs[i]; 2313 slhci_write(sc, slhci_tregs[ab][i], 2314 spipe->tregs[i]); 2315 } 2316 2317 DLOG(D_SXFER, "Transfer len %d pid %#x dev %d type %s", 2318 spipe->tregs[LEN], spipe->tregs[PID], spipe->tregs[DEV], 2319 pnames(spipe->ptype)); 2320 2321 t->spipe[ab] = spipe; 2322 t->flags |= ab ? F_BREADY : F_AREADY; 2323 2324 slhci_tstart(sc); 2325 } 2326 } 2327 2328 /* slhci_callback is called after the lock is taken from splsoftusb. 2329 * s is pointer to old spl (splsoftusb). */ 2330 static void 2331 slhci_callback(struct slhci_softc *sc, int *s) 2332 { 2333 struct slhci_transfers *t; 2334 struct slhci_pipe *spipe; 2335 struct usbd_xfer *xfer; 2336 2337 t = &sc->sc_transfers; 2338 2339 SLHCI_LOCKASSERT(sc, locked, unlocked); 2340 2341 DLOG(D_SOFT, "CB flags %#x", t->flags, 0,0,0); 2342 for (;;) { 2343 if (__predict_false(t->flags & F_ROOTINTR)) { 2344 t->flags &= ~F_ROOTINTR; 2345 if (t->rootintr != NULL) { 2346 u_char *p; 2347 2348 p = KERNADDR(&t->rootintr->dmabuf, 0); 2349 p[0] = 2; 2350 t->rootintr->actlen = 1; 2351 t->rootintr->status = USBD_NORMAL_COMPLETION; 2352 xfer = t->rootintr; 2353 goto do_callback; 2354 } 2355 } 2356 2357 2358 if (!DEQUEUED_CALLBACK(spipe, t)) 2359 return; 2360 2361 xfer = spipe->xfer; 2362 LK_SLASSERT(xfer != NULL, sc, spipe, NULL, return); 2363 spipe->xfer = NULL; 2364 DLOG(D_XFER, "xfer callback length %d actlen %d spipe %x " 2365 "type %s", xfer->length, xfer->actlen, spipe, 2366 pnames(spipe->ptype)); 2367 do_callback: 2368 slhci_do_callback(sc, xfer, s); 2369 } 2370 } 2371 2372 static void 2373 slhci_enter_xfer(struct slhci_softc *sc, struct slhci_pipe *spipe) 2374 { 2375 struct slhci_transfers *t; 2376 2377 t = &sc->sc_transfers; 2378 2379 SLHCI_MAINLOCKASSERT(sc); 2380 2381 if (__predict_false(t->flags & F_DISABLED) || 2382 __predict_false(spipe->pflags & PF_GONE)) { 2383 DLOG(D_MSG, "slhci_enter_xfer: DISABLED or GONE", 0,0,0,0); 2384 spipe->xfer->status = USBD_CANCELLED; 2385 } 2386 2387 if (spipe->xfer->status == USBD_IN_PROGRESS) { 2388 if (spipe->xfer->timeout) { 2389 spipe->to_frame = t->frame + spipe->xfer->timeout; 2390 slhci_xfer_timer(sc, spipe); 2391 } 2392 if (spipe->pipe.interval) 2393 slhci_queue_timed(sc, spipe); 2394 else 2395 enter_q(t, spipe, Q_CB); 2396 } else 2397 enter_callback(t, spipe); 2398 } 2399 2400 #ifdef SLHCI_WAITLOCK 2401 static void 2402 slhci_enter_xfers(struct slhci_softc *sc) 2403 { 2404 struct slhci_pipe *spipe; 2405 2406 SLHCI_LOCKASSERT(sc, locked, locked); 2407 2408 while (DEQUEUED_WAITQ(spipe, sc)) 2409 slhci_enter_xfer(sc, spipe); 2410 } 2411 #endif 2412 2413 static void 2414 slhci_queue_timed(struct slhci_softc *sc, struct slhci_pipe *spipe) 2415 { 2416 struct slhci_transfers *t; 2417 struct gcq *q; 2418 struct slhci_pipe *spp; 2419 2420 t = &sc->sc_transfers; 2421 2422 SLHCI_MAINLOCKASSERT(sc); 2423 2424 FIND_TIMED(q, t, spp, spp->frame > spipe->frame); 2425 gcq_insert_before(q, &spipe->xq); 2426 } 2427 2428 static void 2429 slhci_xfer_timer(struct slhci_softc *sc, struct slhci_pipe *spipe) 2430 { 2431 struct slhci_transfers *t; 2432 struct gcq *q; 2433 struct slhci_pipe *spp; 2434 2435 t = &sc->sc_transfers; 2436 2437 SLHCI_MAINLOCKASSERT(sc); 2438 2439 FIND_TO(q, t, spp, spp->to_frame >= spipe->to_frame); 2440 gcq_insert_before(q, &spipe->to); 2441 } 2442 2443 static void 2444 slhci_do_repeat(struct slhci_softc *sc, struct usbd_xfer *xfer) 2445 { 2446 struct slhci_transfers *t; 2447 struct slhci_pipe *spipe; 2448 2449 t = &sc->sc_transfers; 2450 spipe = (struct slhci_pipe *)xfer->pipe; 2451 2452 if (xfer == t->rootintr) 2453 return; 2454 2455 DLOG(D_TRACE, "REPEAT: xfer %p actlen %d frame %u now %u", 2456 xfer, xfer->actlen, spipe->frame, sc->sc_transfers.frame); 2457 2458 xfer->actlen = 0; 2459 spipe->xfer = xfer; 2460 if (spipe->tregs[LEN]) 2461 KASSERT(spipe->buffer == KERNADDR(&xfer->dmabuf, 0)); 2462 slhci_queue_timed(sc, spipe); 2463 slhci_dotransfer(sc); 2464 } 2465 2466 static void 2467 slhci_callback_schedule(struct slhci_softc *sc) 2468 { 2469 struct slhci_transfers *t; 2470 2471 t = &sc->sc_transfers; 2472 2473 SLHCI_LOCKASSERT(sc, locked, unlocked); 2474 2475 if (t->flags & F_ACTIVE) 2476 slhci_do_callback_schedule(sc); 2477 } 2478 2479 static void 2480 slhci_do_callback_schedule(struct slhci_softc *sc) 2481 { 2482 struct slhci_transfers *t; 2483 2484 t = &sc->sc_transfers; 2485 2486 SLHCI_LOCKASSERT(sc, locked, unlocked); 2487 2488 if (!(t->flags & F_CALLBACK)) { 2489 t->flags |= F_CALLBACK; 2490 softint_schedule(sc->sc_cb_softintr); 2491 } 2492 } 2493 2494 #if 0 2495 /* must be called with lock taken from splsoftusb */ 2496 /* XXX static */ void 2497 slhci_pollxfer(struct slhci_softc *sc, struct usbd_xfer *xfer, int *s) 2498 { 2499 SLHCI_LOCKASSERT(sc, locked, unlocked); 2500 slhci_dotransfer(sc); 2501 do { 2502 slhci_dointr(sc); 2503 } while (xfer->status == USBD_IN_PROGRESS); 2504 slhci_do_callback(sc, xfer, s); 2505 } 2506 #endif 2507 2508 static usbd_status 2509 slhci_do_poll(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2510 usbd_xfer *xfer) 2511 { 2512 slhci_waitintr(sc, 0); 2513 2514 return USBD_NORMAL_COMPLETION; 2515 } 2516 2517 static usbd_status 2518 slhci_lsvh_warn(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2519 usbd_xfer *xfer) 2520 { 2521 struct slhci_transfers *t; 2522 2523 t = &sc->sc_transfers; 2524 2525 if (!(t->flags & F_LSVH_WARNED)) { 2526 printf("%s: Low speed device via hub disabled, " 2527 "see slhci(4)\n", SC_NAME(sc)); 2528 DDOLOG("%s: Low speed device via hub disabled, " 2529 "see slhci(4)\n", SC_NAME(sc), 0,0,0); 2530 t->flags |= F_LSVH_WARNED; 2531 } 2532 return USBD_INVAL; 2533 } 2534 2535 static usbd_status 2536 slhci_isoc_warn(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2537 usbd_xfer *xfer) 2538 { 2539 struct slhci_transfers *t; 2540 2541 t = &sc->sc_transfers; 2542 2543 if (!(t->flags & F_ISOC_WARNED)) { 2544 printf("%s: ISOC transfer not supported " 2545 "(see slhci(4))\n", SC_NAME(sc)); 2546 DDOLOG("%s: ISOC transfer not supported " 2547 "(see slhci(4))\n", SC_NAME(sc), 0,0,0); 2548 t->flags |= F_ISOC_WARNED; 2549 } 2550 return USBD_INVAL; 2551 } 2552 2553 static usbd_status 2554 slhci_open_pipe(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2555 usbd_xfer *xfer) 2556 { 2557 struct slhci_transfers *t; 2558 struct usbd_pipe *pipe; 2559 2560 t = &sc->sc_transfers; 2561 pipe = &spipe->pipe; 2562 2563 if (t->flags & F_DISABLED) 2564 return USBD_CANCELLED; 2565 else if (pipe->interval && !slhci_reserve_bustime(sc, spipe, 1)) 2566 return USBD_PENDING_REQUESTS; 2567 else { 2568 enter_all_pipes(t, spipe); 2569 return USBD_NORMAL_COMPLETION; 2570 } 2571 } 2572 2573 static usbd_status 2574 slhci_close_pipe(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2575 usbd_xfer *xfer) 2576 { 2577 struct slhci_transfers *t; 2578 struct usbd_pipe *pipe; 2579 2580 t = &sc->sc_transfers; 2581 pipe = &spipe->pipe; 2582 2583 if (pipe->interval && spipe->ptype != PT_ROOT_INTR) 2584 slhci_reserve_bustime(sc, spipe, 0); 2585 gcq_remove(&spipe->ap); 2586 return USBD_NORMAL_COMPLETION; 2587 } 2588 2589 static usbd_status 2590 slhci_do_abort(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2591 usbd_xfer *xfer) 2592 { 2593 struct slhci_transfers *t; 2594 2595 t = &sc->sc_transfers; 2596 2597 SLHCI_MAINLOCKASSERT(sc); 2598 2599 if (spipe->xfer == xfer) { 2600 if (spipe->ptype == PT_ROOT_INTR) { 2601 if (t->rootintr == spipe->xfer) /* XXX assert? */ 2602 t->rootintr = NULL; 2603 } else { 2604 gcq_remove(&spipe->to); 2605 gcq_remove(&spipe->xq); 2606 2607 if (t->spipe[A] == spipe) { 2608 t->spipe[A] = NULL; 2609 if (!(t->flags & F_AINPROG)) 2610 t->len[A] = -1; 2611 } else if (t->spipe[B] == spipe) { 2612 t->spipe[B] = NULL; 2613 if (!(t->flags & F_BINPROG)) 2614 t->len[B] = -1; 2615 } 2616 } 2617 2618 if (xfer->status != USBD_TIMEOUT) { 2619 spipe->xfer = NULL; 2620 spipe->pipe.repeat = 0; /* XXX timeout? */ 2621 } 2622 } 2623 2624 return USBD_NORMAL_COMPLETION; 2625 } 2626 2627 static usbd_status 2628 slhci_do_attach(struct slhci_softc *sc, struct slhci_pipe *spipe, struct 2629 usbd_xfer *xfer) 2630 { 2631 struct slhci_transfers *t; 2632 const char *rev; 2633 2634 t = &sc->sc_transfers; 2635 2636 SLHCI_LOCKASSERT(sc, locked, unlocked); 2637 2638 /* Detect and check the controller type */ 2639 t->sltype = SL11_GET_REV(slhci_read(sc, SL11_REV)); 2640 2641 /* SL11H not supported */ 2642 if (!slhci_supported_rev(t->sltype)) { 2643 if (t->sltype == SLTYPE_SL11H) 2644 printf("%s: SL11H unsupported or bus error!\n", 2645 SC_NAME(sc)); 2646 else 2647 printf("%s: Unknown chip revision!\n", SC_NAME(sc)); 2648 return USBD_INVAL; 2649 } 2650 2651 callout_init(&sc->sc_timer, CALLOUT_MPSAFE); 2652 callout_setfunc(&sc->sc_timer, slhci_reset_entry, sc); 2653 2654 /* It is not safe to call the soft interrupt directly as 2655 * usb_schedsoftintr does in the use_polling case (due to locking). 2656 */ 2657 sc->sc_cb_softintr = softint_establish(SOFTINT_NET, 2658 slhci_callback_entry, sc); 2659 2660 #ifdef SLHCI_DEBUG 2661 ssc = sc; 2662 #ifdef USB_DEBUG 2663 if (slhci_usbdebug >= 0) 2664 usbdebug = slhci_usbdebug; 2665 #endif 2666 #endif 2667 2668 if (t->sltype == SLTYPE_SL811HS_R12) 2669 rev = " (rev 1.2)"; 2670 else if (t->sltype == SLTYPE_SL811HS_R14) 2671 rev = " (rev 1.4 or 1.5)"; 2672 else 2673 rev = " (unknown revision)"; 2674 2675 aprint_normal("%s: ScanLogic SL811HS/T USB Host Controller %s\n", 2676 SC_NAME(sc), rev); 2677 2678 aprint_normal("%s: Max Current %u mA (value by code, not by probe)\n", 2679 SC_NAME(sc), t->max_current * 2); 2680 2681 #if defined(SLHCI_DEBUG) || defined(SLHCI_NO_OVERTIME) || \ 2682 defined(SLHCI_TRY_LSVH) || defined(SLHCI_PROFILE_TRANSFER) 2683 aprint_normal("%s: driver options:" 2684 #ifdef SLHCI_DEBUG 2685 " SLHCI_DEBUG" 2686 #endif 2687 #ifdef SLHCI_TRY_LSVH 2688 " SLHCI_TRY_LSVH" 2689 #endif 2690 #ifdef SLHCI_NO_OVERTIME 2691 " SLHCI_NO_OVERTIME" 2692 #endif 2693 #ifdef SLHCI_PROFILE_TRANSFER 2694 " SLHCI_PROFILE_TRANSFER" 2695 #endif 2696 "\n", SC_NAME(sc)); 2697 #endif 2698 sc->sc_bus.usbrev = USBREV_1_1; 2699 sc->sc_bus.methods = __UNCONST(&slhci_bus_methods); 2700 sc->sc_bus.pipe_size = sizeof(struct slhci_pipe); 2701 2702 if (!sc->sc_enable_power) 2703 t->flags |= F_REALPOWER; 2704 2705 t->flags |= F_ACTIVE; 2706 2707 return USBD_NORMAL_COMPLETION; 2708 } 2709 2710 /* Called to deactivate or stop use of the controller instead of panicing. 2711 * Will cancel the xfer correctly even when not on a list. 2712 */ 2713 static usbd_status 2714 slhci_halt(struct slhci_softc *sc, struct slhci_pipe *spipe, struct usbd_xfer 2715 *xfer) 2716 { 2717 struct slhci_transfers *t; 2718 2719 SLHCI_LOCKASSERT(sc, locked, unlocked); 2720 2721 t = &sc->sc_transfers; 2722 2723 DDOLOG("Halt! sc %p spipe %p xfer %p", sc, spipe, xfer, 0); 2724 2725 if (spipe != NULL) 2726 slhci_log_spipe(spipe); 2727 2728 if (xfer != NULL) 2729 slhci_log_xfer(xfer); 2730 2731 if (spipe != NULL && xfer != NULL && spipe->xfer == xfer && 2732 !gcq_onlist(&spipe->xq) && t->spipe[A] != spipe && t->spipe[B] != 2733 spipe) { 2734 xfer->status = USBD_CANCELLED; 2735 enter_callback(t, spipe); 2736 } 2737 2738 if (t->flags & F_ACTIVE) { 2739 slhci_intrchange(sc, 0); 2740 /* leave power on when halting in case flash devices or disks 2741 * are attached, which may be writing and could be damaged 2742 * by abrupt power loss. The root hub clear power feature 2743 * should still work after halting. 2744 */ 2745 } 2746 2747 t->flags &= ~F_ACTIVE; 2748 t->flags |= F_UDISABLED; 2749 if (!(t->flags & F_NODEV)) 2750 t->flags |= F_NODEV|F_CCONNECT|F_ROOTINTR; 2751 slhci_drain(sc); 2752 2753 /* One last callback for the drain and device removal. */ 2754 slhci_do_callback_schedule(sc); 2755 2756 return USBD_NORMAL_COMPLETION; 2757 } 2758 2759 /* There are three interrupt states: no interrupts during reset and after 2760 * device deactivation, INSERT only for no device present but power on, and 2761 * SOF, INSERT, ADONE, and BDONE when device is present. 2762 */ 2763 static void 2764 slhci_intrchange(struct slhci_softc *sc, uint8_t new_ier) 2765 { 2766 SLHCI_MAINLOCKASSERT(sc); 2767 if (sc->sc_ier != new_ier) { 2768 sc->sc_ier = new_ier; 2769 slhci_write(sc, SL11_IER, new_ier); 2770 BSB_SYNC(sc->iot, sc->ioh, sc->pst, sc->psz); 2771 } 2772 } 2773 2774 /* Drain: cancel all pending transfers and put them on the callback list and 2775 * set the UDISABLED flag. UDISABLED is cleared only by reset. */ 2776 static void 2777 slhci_drain(struct slhci_softc *sc) 2778 { 2779 struct slhci_transfers *t; 2780 struct slhci_pipe *spipe; 2781 struct gcq *q; 2782 int i; 2783 2784 SLHCI_LOCKASSERT(sc, locked, unlocked); 2785 2786 t = &sc->sc_transfers; 2787 2788 DLOG(D_MSG, "DRAIN flags %#x", t->flags, 0,0,0); 2789 2790 t->pend = INT_MAX; 2791 2792 for (i=0; i<=1; i++) { 2793 t->len[i] = -1; 2794 if (t->spipe[i] != NULL) { 2795 enter_callback(t, t->spipe[i]); 2796 t->spipe[i] = NULL; 2797 } 2798 } 2799 2800 /* Merge the queues into the callback queue. */ 2801 gcq_merge_tail(&t->q[Q_CALLBACKS], &t->q[Q_CB]); 2802 gcq_merge_tail(&t->q[Q_CALLBACKS], &t->q[Q_NEXT_CB]); 2803 gcq_merge_tail(&t->q[Q_CALLBACKS], &t->timed); 2804 2805 /* Cancel all pipes. Note that not all of these may be on the 2806 * callback queue yet; some could be in slhci_start, for example. */ 2807 FOREACH_AP(q, t, spipe) { 2808 spipe->pflags = PF_GONE; 2809 spipe->pipe.repeat = 0; 2810 spipe->pipe.aborting = 1; 2811 if (spipe->xfer != NULL) 2812 spipe->xfer->status = USBD_CANCELLED; 2813 } 2814 2815 gcq_remove_all(&t->to); 2816 2817 t->flags |= F_UDISABLED; 2818 t->flags &= ~(F_AREADY|F_BREADY|F_AINPROG|F_BINPROG|F_LOWSPEED); 2819 } 2820 2821 /* RESET: SL11_CTRL_RESETENGINE=1 and SL11_CTRL_JKSTATE=0 for 50ms 2822 * reconfigure SOF after reset, must wait 2.5us before USB bus activity (SOF) 2823 * check attached device speed. 2824 * must wait 100ms before USB transaction according to app note, 10ms 2825 * by spec. uhub does this delay 2826 * 2827 * Started from root hub set feature reset, which does step one. 2828 * use_polling will call slhci_reset directly, otherwise the callout goes 2829 * through slhci_reset_entry. 2830 */ 2831 void 2832 slhci_reset(struct slhci_softc *sc) 2833 { 2834 struct slhci_transfers *t; 2835 uint8_t r, pol, ctrl; 2836 2837 t = &sc->sc_transfers; 2838 SLHCI_MAINLOCKASSERT(sc); 2839 2840 stop_cc_time(&t_delay); 2841 2842 KASSERT(t->flags & F_ACTIVE); 2843 2844 start_cc_time(&t_delay, 0); 2845 stop_cc_time(&t_delay); 2846 2847 slhci_write(sc, SL11_CTRL, 0); 2848 start_cc_time(&t_delay, 3); 2849 DELAY(3); 2850 stop_cc_time(&t_delay); 2851 slhci_write(sc, SL11_ISR, 0xff); 2852 2853 r = slhci_read(sc, SL11_ISR); 2854 2855 if (r & SL11_ISR_INSERT) 2856 slhci_write(sc, SL11_ISR, SL11_ISR_INSERT); 2857 2858 if (r & SL11_ISR_NODEV) { 2859 DLOG(D_MSG, "NC", 0,0,0,0); 2860 /* Normally, the hard interrupt insert routine will issue 2861 * CCONNECT, however we need to do it here if the detach 2862 * happened during reset. */ 2863 if (!(t->flags & F_NODEV)) 2864 t->flags |= F_CCONNECT|F_ROOTINTR|F_NODEV; 2865 slhci_intrchange(sc, SL11_IER_INSERT); 2866 } else { 2867 if (t->flags & F_NODEV) 2868 t->flags |= F_CCONNECT; 2869 t->flags &= ~(F_NODEV|F_LOWSPEED); 2870 if (r & SL11_ISR_DATA) { 2871 DLOG(D_MSG, "FS", 0,0,0,0); 2872 pol = ctrl = 0; 2873 } else { 2874 DLOG(D_MSG, "LS", 0,0,0,0); 2875 pol = SL811_CSOF_POLARITY; 2876 ctrl = SL11_CTRL_LOWSPEED; 2877 t->flags |= F_LOWSPEED; 2878 } 2879 2880 /* Enable SOF auto-generation */ 2881 t->frame = 0; /* write to SL811_CSOF will reset frame */ 2882 slhci_write(sc, SL11_SOFTIME, 0xe0); 2883 slhci_write(sc, SL811_CSOF, pol|SL811_CSOF_MASTER|0x2e); 2884 slhci_write(sc, SL11_CTRL, ctrl|SL11_CTRL_ENABLESOF); 2885 2886 /* According to the app note, ARM must be set 2887 * for SOF generation to work. We initialize all 2888 * USBA registers here for current_tregs. */ 2889 slhci_write(sc, SL11_E0ADDR, SL11_BUFFER_START); 2890 slhci_write(sc, SL11_E0LEN, 0); 2891 slhci_write(sc, SL11_E0PID, SL11_PID_SOF); 2892 slhci_write(sc, SL11_E0DEV, 0); 2893 slhci_write(sc, SL11_E0CTRL, SL11_EPCTRL_ARM); 2894 2895 /* Initialize B registers. This can't be done earlier since 2896 * they are not valid until the SL811_CSOF register is written 2897 * above due to SL11H compatability. */ 2898 slhci_write(sc, SL11_E1ADDR, SL11_BUFFER_END - 8); 2899 slhci_write(sc, SL11_E1LEN, 0); 2900 slhci_write(sc, SL11_E1PID, 0); 2901 slhci_write(sc, SL11_E1DEV, 0); 2902 2903 t->current_tregs[0][ADR] = SL11_BUFFER_START; 2904 t->current_tregs[0][LEN] = 0; 2905 t->current_tregs[0][PID] = SL11_PID_SOF; 2906 t->current_tregs[0][DEV] = 0; 2907 t->current_tregs[1][ADR] = SL11_BUFFER_END - 8; 2908 t->current_tregs[1][LEN] = 0; 2909 t->current_tregs[1][PID] = 0; 2910 t->current_tregs[1][DEV] = 0; 2911 2912 /* SOF start will produce USBA interrupt */ 2913 t->len[A] = 0; 2914 t->flags |= F_AINPROG; 2915 2916 slhci_intrchange(sc, SLHCI_NORMAL_INTERRUPTS); 2917 } 2918 2919 t->flags &= ~(F_UDISABLED|F_RESET); 2920 t->flags |= F_CRESET|F_ROOTINTR; 2921 DLOG(D_MSG, "RESET done flags %#x", t->flags, 0,0,0); 2922 } 2923 2924 /* returns 1 if succeeded, 0 if failed, reserve == 0 is unreserve */ 2925 static int 2926 slhci_reserve_bustime(struct slhci_softc *sc, struct slhci_pipe *spipe, int 2927 reserve) 2928 { 2929 struct slhci_transfers *t; 2930 int bustime, max_packet; 2931 2932 SLHCI_LOCKASSERT(sc, locked, unlocked); 2933 2934 t = &sc->sc_transfers; 2935 max_packet = UGETW(spipe->pipe.endpoint->edesc->wMaxPacketSize); 2936 2937 if (spipe->pflags & PF_LS) 2938 bustime = SLHCI_LS_CONST + SLHCI_LS_DATA_TIME(max_packet); 2939 else 2940 bustime = SLHCI_FS_CONST + SLHCI_FS_DATA_TIME(max_packet); 2941 2942 if (!reserve) { 2943 t->reserved_bustime -= bustime; 2944 #ifdef DIAGNOSTIC 2945 if (t->reserved_bustime < 0) { 2946 printf("%s: reserved_bustime %d < 0!\n", 2947 SC_NAME(sc), t->reserved_bustime); 2948 DDOLOG("%s: reserved_bustime %d < 0!\n", 2949 SC_NAME(sc), t->reserved_bustime, 0,0); 2950 t->reserved_bustime = 0; 2951 } 2952 #endif 2953 return 1; 2954 } 2955 2956 if (t->reserved_bustime + bustime > SLHCI_RESERVED_BUSTIME) { 2957 if (ratecheck(&sc->sc_reserved_warn_rate, 2958 &reserved_warn_rate)) 2959 #ifdef SLHCI_NO_OVERTIME 2960 { 2961 printf("%s: Max reserved bus time exceeded! " 2962 "Erroring request.\n", SC_NAME(sc)); 2963 DDOLOG("%s: Max reserved bus time exceeded! " 2964 "Erroring request.\n", SC_NAME(sc), 0,0,0); 2965 } 2966 return 0; 2967 #else 2968 { 2969 printf("%s: Reserved bus time exceeds %d!\n", 2970 SC_NAME(sc), SLHCI_RESERVED_BUSTIME); 2971 DDOLOG("%s: Reserved bus time exceeds %d!\n", 2972 SC_NAME(sc), SLHCI_RESERVED_BUSTIME, 0,0); 2973 } 2974 #endif 2975 } 2976 2977 t->reserved_bustime += bustime; 2978 return 1; 2979 } 2980 2981 /* Device insertion/removal interrupt */ 2982 static void 2983 slhci_insert(struct slhci_softc *sc) 2984 { 2985 struct slhci_transfers *t; 2986 2987 t = &sc->sc_transfers; 2988 2989 SLHCI_LOCKASSERT(sc, locked, unlocked); 2990 2991 if (t->flags & F_NODEV) 2992 slhci_intrchange(sc, 0); 2993 else { 2994 slhci_drain(sc); 2995 slhci_intrchange(sc, SL11_IER_INSERT); 2996 } 2997 t->flags ^= F_NODEV; 2998 t->flags |= F_ROOTINTR|F_CCONNECT; 2999 DLOG(D_MSG, "INSERT intr: flags after %#x", t->flags, 0,0,0); 3000 } 3001 3002 /* 3003 * Data structures and routines to emulate the root hub. 3004 */ 3005 static const usb_device_descriptor_t slhci_devd = { 3006 USB_DEVICE_DESCRIPTOR_SIZE, 3007 UDESC_DEVICE, /* type */ 3008 {0x01, 0x01}, /* USB version */ 3009 UDCLASS_HUB, /* class */ 3010 UDSUBCLASS_HUB, /* subclass */ 3011 0, /* protocol */ 3012 64, /* max packet */ 3013 {USB_VENDOR_SCANLOGIC & 0xff, /* vendor ID (low) */ 3014 USB_VENDOR_SCANLOGIC >> 8 }, /* vendor ID (high) */ 3015 {0} /* ? */, /* product ID */ 3016 {0}, /* device */ 3017 1, /* index to manufacturer */ 3018 2, /* index to product */ 3019 0, /* index to serial number */ 3020 1 /* number of configurations */ 3021 }; 3022 3023 static const struct slhci_confd_t { 3024 const usb_config_descriptor_t confd; 3025 const usb_interface_descriptor_t ifcd; 3026 const usb_endpoint_descriptor_t endpd; 3027 } UPACKED slhci_confd = { 3028 { /* Configuration */ 3029 USB_CONFIG_DESCRIPTOR_SIZE, 3030 UDESC_CONFIG, 3031 {USB_CONFIG_DESCRIPTOR_SIZE + 3032 USB_INTERFACE_DESCRIPTOR_SIZE + 3033 USB_ENDPOINT_DESCRIPTOR_SIZE}, 3034 1, /* number of interfaces */ 3035 1, /* configuration value */ 3036 0, /* index to configuration */ 3037 UC_SELF_POWERED, /* attributes */ 3038 0 /* max current, filled in later */ 3039 }, { /* Interface */ 3040 USB_INTERFACE_DESCRIPTOR_SIZE, 3041 UDESC_INTERFACE, 3042 0, /* interface number */ 3043 0, /* alternate setting */ 3044 1, /* number of endpoint */ 3045 UICLASS_HUB, /* class */ 3046 UISUBCLASS_HUB, /* subclass */ 3047 0, /* protocol */ 3048 0 /* index to interface */ 3049 }, { /* Endpoint */ 3050 USB_ENDPOINT_DESCRIPTOR_SIZE, 3051 UDESC_ENDPOINT, 3052 UE_DIR_IN | ROOT_INTR_ENDPT, /* endpoint address */ 3053 UE_INTERRUPT, /* attributes */ 3054 {240, 0}, /* max packet size */ 3055 255 /* interval */ 3056 } 3057 }; 3058 3059 static const usb_hub_descriptor_t slhci_hubd = { 3060 USB_HUB_DESCRIPTOR_SIZE, 3061 UDESC_HUB, 3062 1, /* number of ports */ 3063 {UHD_PWR_INDIVIDUAL | UHD_OC_NONE, 0}, /* hub characteristics */ 3064 50, /* 5:power on to power good, units of 2ms */ 3065 0, /* 6:maximum current, filled in later */ 3066 { 0x00 }, /* port is removable */ 3067 { 0x00 } /* port power control mask */ 3068 }; 3069 3070 static usbd_status 3071 slhci_clear_feature(struct slhci_softc *sc, unsigned int what) 3072 { 3073 struct slhci_transfers *t; 3074 usbd_status error; 3075 3076 t = &sc->sc_transfers; 3077 error = USBD_NORMAL_COMPLETION; 3078 3079 SLHCI_LOCKASSERT(sc, locked, unlocked); 3080 3081 if (what == UHF_PORT_POWER) { 3082 DLOG(D_MSG, "POWER_OFF", 0,0,0,0); 3083 t->flags &= ~F_POWER; 3084 if (!(t->flags & F_NODEV)) 3085 t->flags |= F_NODEV|F_CCONNECT|F_ROOTINTR; 3086 /* for x68k Nereid USB controller */ 3087 if (sc->sc_enable_power && (t->flags & F_REALPOWER)) { 3088 t->flags &= ~F_REALPOWER; 3089 sc->sc_enable_power(sc, POWER_OFF); 3090 } 3091 slhci_intrchange(sc, 0); 3092 slhci_drain(sc); 3093 } else if (what == UHF_C_PORT_CONNECTION) { 3094 t->flags &= ~F_CCONNECT; 3095 } else if (what == UHF_C_PORT_RESET) { 3096 t->flags &= ~F_CRESET; 3097 } else if (what == UHF_PORT_ENABLE) { 3098 slhci_drain(sc); 3099 } else if (what != UHF_PORT_SUSPEND) { 3100 DDOLOG("ClrPortFeatERR:value=%#.4x", what, 0,0,0); 3101 error = USBD_IOERROR; 3102 } 3103 3104 return error; 3105 } 3106 3107 static usbd_status 3108 slhci_set_feature(struct slhci_softc *sc, unsigned int what) 3109 { 3110 struct slhci_transfers *t; 3111 uint8_t r; 3112 3113 t = &sc->sc_transfers; 3114 3115 SLHCI_LOCKASSERT(sc, locked, unlocked); 3116 3117 if (what == UHF_PORT_RESET) { 3118 if (!(t->flags & F_ACTIVE)) { 3119 DDOLOG("SET PORT_RESET when not ACTIVE!", 3120 0,0,0,0); 3121 return USBD_INVAL; 3122 } 3123 if (!(t->flags & F_POWER)) { 3124 DDOLOG("SET PORT_RESET without PORT_POWER! flags %p", 3125 t->flags, 0,0,0); 3126 return USBD_INVAL; 3127 } 3128 if (t->flags & F_RESET) 3129 return USBD_NORMAL_COMPLETION; 3130 DLOG(D_MSG, "RESET flags %#x", t->flags, 0,0,0); 3131 slhci_intrchange(sc, 0); 3132 slhci_drain(sc); 3133 slhci_write(sc, SL11_CTRL, SL11_CTRL_RESETENGINE); 3134 /* usb spec says delay >= 10ms, app note 50ms */ 3135 start_cc_time(&t_delay, 50000); 3136 if (sc->sc_bus.use_polling) { 3137 DELAY(50000); 3138 slhci_reset(sc); 3139 } else { 3140 t->flags |= F_RESET; 3141 callout_schedule(&sc->sc_timer, max(mstohz(50), 2)); 3142 } 3143 } else if (what == UHF_PORT_SUSPEND) { 3144 printf("%s: USB Suspend not implemented!\n", SC_NAME(sc)); 3145 DDOLOG("%s: USB Suspend not implemented!\n", SC_NAME(sc), 3146 0,0,0); 3147 } else if (what == UHF_PORT_POWER) { 3148 DLOG(D_MSG, "PORT_POWER", 0,0,0,0); 3149 /* for x68k Nereid USB controller */ 3150 if (!(t->flags & F_ACTIVE)) 3151 return USBD_INVAL; 3152 if (t->flags & F_POWER) 3153 return USBD_NORMAL_COMPLETION; 3154 if (!(t->flags & F_REALPOWER)) { 3155 if (sc->sc_enable_power) 3156 sc->sc_enable_power(sc, POWER_ON); 3157 t->flags |= F_REALPOWER; 3158 } 3159 t->flags |= F_POWER; 3160 r = slhci_read(sc, SL11_ISR); 3161 if (r & SL11_ISR_INSERT) 3162 slhci_write(sc, SL11_ISR, SL11_ISR_INSERT); 3163 if (r & SL11_ISR_NODEV) { 3164 slhci_intrchange(sc, SL11_IER_INSERT); 3165 t->flags |= F_NODEV; 3166 } else { 3167 t->flags &= ~F_NODEV; 3168 t->flags |= F_CCONNECT|F_ROOTINTR; 3169 } 3170 } else { 3171 DDOLOG("SetPortFeatERR=%#.8x", what, 0,0,0); 3172 return USBD_IOERROR; 3173 } 3174 3175 return USBD_NORMAL_COMPLETION; 3176 } 3177 3178 static void 3179 slhci_get_status(struct slhci_softc *sc, usb_port_status_t *ps) 3180 { 3181 struct slhci_transfers *t; 3182 unsigned int status, change; 3183 3184 t = &sc->sc_transfers; 3185 3186 SLHCI_LOCKASSERT(sc, locked, unlocked); 3187 3188 /* We do not have a way to detect over current or bable and 3189 * suspend is currently not implemented, so connect and reset 3190 * are the only changes that need to be reported. */ 3191 change = 0; 3192 if (t->flags & F_CCONNECT) 3193 change |= UPS_C_CONNECT_STATUS; 3194 if (t->flags & F_CRESET) 3195 change |= UPS_C_PORT_RESET; 3196 3197 status = 0; 3198 if (!(t->flags & F_NODEV)) 3199 status |= UPS_CURRENT_CONNECT_STATUS; 3200 if (!(t->flags & F_UDISABLED)) 3201 status |= UPS_PORT_ENABLED; 3202 if (t->flags & F_RESET) 3203 status |= UPS_RESET; 3204 if (t->flags & F_POWER) 3205 status |= UPS_PORT_POWER; 3206 if (t->flags & F_LOWSPEED) 3207 status |= UPS_LOW_SPEED; 3208 USETW(ps->wPortStatus, status); 3209 USETW(ps->wPortChange, change); 3210 DLOG(D_ROOT, "status=%#.4x, change=%#.4x", status, change, 0,0); 3211 } 3212 3213 static usbd_status 3214 slhci_root(struct slhci_softc *sc, struct slhci_pipe *spipe, struct usbd_xfer 3215 *xfer) 3216 { 3217 struct slhci_transfers *t; 3218 usb_device_request_t *req; 3219 unsigned int len, value, index, actlen, type; 3220 uint8_t *buf; 3221 usbd_status error; 3222 3223 t = &sc->sc_transfers; 3224 buf = NULL; 3225 3226 LK_SLASSERT(spipe != NULL && xfer != NULL, sc, spipe, xfer, return 3227 USBD_CANCELLED); 3228 3229 DLOG(D_TRACE, "%s start", pnames(SLHCI_XFER_TYPE(xfer)), 0,0,0); 3230 SLHCI_LOCKASSERT(sc, locked, unlocked); 3231 3232 if (spipe->ptype == PT_ROOT_INTR) { 3233 LK_SLASSERT(t->rootintr == NULL, sc, spipe, xfer, return 3234 USBD_CANCELLED); 3235 t->rootintr = xfer; 3236 if (t->flags & F_CHANGE) 3237 t->flags |= F_ROOTINTR; 3238 return USBD_IN_PROGRESS; 3239 } 3240 3241 error = USBD_IOERROR; /* XXX should be STALL */ 3242 actlen = 0; 3243 req = &xfer->request; 3244 3245 len = UGETW(req->wLength); 3246 value = UGETW(req->wValue); 3247 index = UGETW(req->wIndex); 3248 3249 type = req->bmRequestType; 3250 3251 if (len) 3252 buf = KERNADDR(&xfer->dmabuf, 0); 3253 3254 SLHCI_DEXEC(D_TRACE, slhci_log_req_hub(req)); 3255 3256 /* 3257 * USB requests for hubs have two basic types, standard and class. 3258 * Each could potentially have recipients of device, interface, 3259 * endpoint, or other. For the hub class, CLASS_OTHER means the port 3260 * and CLASS_DEVICE means the hub. For standard requests, OTHER 3261 * is not used. Standard request are described in section 9.4 of the 3262 * standard, hub class requests in 11.16. Each request is either read 3263 * or write. 3264 * 3265 * Clear Feature, Set Feature, and Status are defined for each of the 3266 * used recipients. Get Descriptor and Set Descriptor are defined for 3267 * both standard and hub class types with different descriptors. 3268 * Other requests have only one defined recipient and type. These 3269 * include: Get/Set Address, Get/Set Configuration, Get/Set Interface, 3270 * and Synch Frame for standard requests and Get Bus State for hub 3271 * class. 3272 * 3273 * When a device is first powered up it has address 0 until the 3274 * address is set. 3275 * 3276 * Hubs are only allowed to support one interface and may not have 3277 * isochronous endpoints. The results of the related requests are 3278 * undefined. 3279 * 3280 * The standard requires invalid or unsupported requests to return 3281 * STALL in the data stage, however this does not work well with 3282 * current error handling. XXX 3283 * 3284 * Some unsupported fields: 3285 * Clear Hub Feature is for C_HUB_LOCAL_POWER and C_HUB_OVER_CURRENT 3286 * Set Device Features is for ENDPOINT_HALT and DEVICE_REMOTE_WAKEUP 3287 * Get Bus State is optional sample of D- and D+ at EOF2 3288 */ 3289 3290 switch (req->bRequest) { 3291 /* Write Requests */ 3292 case UR_CLEAR_FEATURE: 3293 if (type == UT_WRITE_CLASS_OTHER) { 3294 if (index == 1 /* Port */) 3295 error = slhci_clear_feature(sc, value); 3296 else 3297 DLOG(D_ROOT, "Clear Port Feature " 3298 "index = %#.4x", index, 0,0,0); 3299 } 3300 break; 3301 case UR_SET_FEATURE: 3302 if (type == UT_WRITE_CLASS_OTHER) { 3303 if (index == 1 /* Port */) 3304 error = slhci_set_feature(sc, value); 3305 else 3306 DLOG(D_ROOT, "Set Port Feature " 3307 "index = %#.4x", index, 0,0,0); 3308 } else if (type != UT_WRITE_CLASS_DEVICE) 3309 DLOG(D_ROOT, "Set Device Feature " 3310 "ENDPOINT_HALT or DEVICE_REMOTE_WAKEUP " 3311 "not supported", 0,0,0,0); 3312 break; 3313 case UR_SET_ADDRESS: 3314 if (type == UT_WRITE_DEVICE) { 3315 DLOG(D_ROOT, "Set Address %#.4x", value, 0,0,0); 3316 if (value < USB_MAX_DEVICES) { 3317 t->rootaddr = value; 3318 error = USBD_NORMAL_COMPLETION; 3319 } 3320 } 3321 break; 3322 case UR_SET_CONFIG: 3323 if (type == UT_WRITE_DEVICE) { 3324 DLOG(D_ROOT, "Set Config %#.4x", value, 0,0,0); 3325 if (value == 0 || value == 1) { 3326 t->rootconf = value; 3327 error = USBD_NORMAL_COMPLETION; 3328 } 3329 } 3330 break; 3331 /* Read Requests */ 3332 case UR_GET_STATUS: 3333 if (type == UT_READ_CLASS_OTHER) { 3334 if (index == 1 /* Port */ && len == /* XXX >=? */ 3335 sizeof(usb_port_status_t)) { 3336 slhci_get_status(sc, (usb_port_status_t *) 3337 buf); 3338 actlen = sizeof(usb_port_status_t); 3339 error = USBD_NORMAL_COMPLETION; 3340 } else 3341 DLOG(D_ROOT, "Get Port Status index = %#.4x " 3342 "len = %#.4x", index, len, 0,0); 3343 } else if (type == UT_READ_CLASS_DEVICE) { /* XXX index? */ 3344 if (len == sizeof(usb_hub_status_t)) { 3345 DLOG(D_ROOT, "Get Hub Status", 3346 0,0,0,0); 3347 actlen = sizeof(usb_hub_status_t); 3348 memset(buf, 0, actlen); 3349 error = USBD_NORMAL_COMPLETION; 3350 } else 3351 DLOG(D_ROOT, "Get Hub Status bad len %#.4x", 3352 len, 0,0,0); 3353 } else if (type == UT_READ_DEVICE) { 3354 if (len >= 2) { 3355 USETW(((usb_status_t *)buf)->wStatus, UDS_SELF_POWERED); 3356 actlen = 2; 3357 error = USBD_NORMAL_COMPLETION; 3358 } 3359 } else if (type == (UT_READ_INTERFACE|UT_READ_ENDPOINT)) { 3360 if (len >= 2) { 3361 USETW(((usb_status_t *)buf)->wStatus, 0); 3362 actlen = 2; 3363 error = USBD_NORMAL_COMPLETION; 3364 } 3365 } 3366 break; 3367 case UR_GET_CONFIG: 3368 if (type == UT_READ_DEVICE) { 3369 DLOG(D_ROOT, "Get Config", 0,0,0,0); 3370 if (len > 0) { 3371 *buf = t->rootconf; 3372 actlen = 1; 3373 error = USBD_NORMAL_COMPLETION; 3374 } 3375 } 3376 break; 3377 case UR_GET_INTERFACE: 3378 if (type == UT_READ_INTERFACE) { 3379 if (len > 0) { 3380 *buf = 0; 3381 actlen = 1; 3382 error = USBD_NORMAL_COMPLETION; 3383 } 3384 } 3385 break; 3386 case UR_GET_DESCRIPTOR: 3387 if (type == UT_READ_DEVICE) { 3388 /* value is type (&0xff00) and index (0xff) */ 3389 if (value == (UDESC_DEVICE<<8)) { 3390 actlen = min(len, sizeof(slhci_devd)); 3391 memcpy(buf, &slhci_devd, actlen); 3392 error = USBD_NORMAL_COMPLETION; 3393 } else if (value == (UDESC_CONFIG<<8)) { 3394 actlen = min(len, sizeof(slhci_confd)); 3395 memcpy(buf, &slhci_confd, actlen); 3396 if (actlen > offsetof(usb_config_descriptor_t, 3397 bMaxPower)) 3398 ((usb_config_descriptor_t *) 3399 buf)->bMaxPower = t->max_current; 3400 /* 2 mA units */ 3401 error = USBD_NORMAL_COMPLETION; 3402 } else if (value == (UDESC_STRING<<8)) { 3403 /* language table XXX */ 3404 } else if (value == ((UDESC_STRING<<8)|1)) { 3405 /* Vendor */ 3406 actlen = usb_makestrdesc((usb_string_descriptor_t *) 3407 buf, len, "ScanLogic/Cypress"); 3408 error = USBD_NORMAL_COMPLETION; 3409 } else if (value == ((UDESC_STRING<<8)|2)) { 3410 /* Product */ 3411 actlen = usb_makestrdesc((usb_string_descriptor_t *) 3412 buf, len, "SL811HS/T root hub"); 3413 error = USBD_NORMAL_COMPLETION; 3414 } else 3415 DDOLOG("Unknown Get Descriptor %#.4x", 3416 value, 0,0,0); 3417 } else if (type == UT_READ_CLASS_DEVICE) { 3418 /* Descriptor number is 0 */ 3419 if (value == (UDESC_HUB<<8)) { 3420 actlen = min(len, sizeof(slhci_hubd)); 3421 memcpy(buf, &slhci_hubd, actlen); 3422 if (actlen > offsetof(usb_config_descriptor_t, 3423 bMaxPower)) 3424 ((usb_hub_descriptor_t *) 3425 buf)->bHubContrCurrent = 500 - 3426 t->max_current; 3427 error = USBD_NORMAL_COMPLETION; 3428 } else 3429 DDOLOG("Unknown Get Hub Descriptor %#.4x", 3430 value, 0,0,0); 3431 } 3432 break; 3433 } 3434 3435 if (error == USBD_NORMAL_COMPLETION) 3436 xfer->actlen = actlen; 3437 xfer->status = error; 3438 KASSERT(spipe->xfer == NULL); 3439 spipe->xfer = xfer; 3440 enter_callback(t, spipe); 3441 3442 return USBD_IN_PROGRESS; 3443 } 3444 3445 /* End in lock functions. Start debug functions. */ 3446 3447 #ifdef SLHCI_DEBUG 3448 void 3449 slhci_log_buffer(struct usbd_xfer *xfer) 3450 { 3451 u_char *buf; 3452 3453 if(xfer->length > 0 && 3454 UE_GET_DIR(xfer->pipe->endpoint->edesc->bEndpointAddress) == 3455 UE_DIR_IN) { 3456 buf = KERNADDR(&xfer->dmabuf, 0); 3457 DDOLOGBUF(buf, xfer->actlen); 3458 DDOLOG("len %d actlen %d short %d", xfer->length, 3459 xfer->actlen, xfer->length - xfer->actlen, 0); 3460 } 3461 } 3462 3463 void 3464 slhci_log_req(usb_device_request_t *r) 3465 { 3466 static const char *xmes[]={ 3467 "GETSTAT", 3468 "CLRFEAT", 3469 "res", 3470 "SETFEAT", 3471 "res", 3472 "SETADDR", 3473 "GETDESC", 3474 "SETDESC", 3475 "GETCONF", 3476 "SETCONF", 3477 "GETIN/F", 3478 "SETIN/F", 3479 "SYNC_FR", 3480 "UNKNOWN" 3481 }; 3482 int req, mreq, type, value, index, len; 3483 3484 req = r->bRequest; 3485 mreq = (req > 13) ? 13 : req; 3486 type = r->bmRequestType; 3487 value = UGETW(r->wValue); 3488 index = UGETW(r->wIndex); 3489 len = UGETW(r->wLength); 3490 3491 DDOLOG("request: %s %#x", xmes[mreq], type, 0,0); 3492 DDOLOG("request: r=%d,v=%d,i=%d,l=%d ", req, value, index, len); 3493 } 3494 3495 void 3496 slhci_log_req_hub(usb_device_request_t *r) 3497 { 3498 static const struct { 3499 int req; 3500 int type; 3501 const char *str; 3502 } conf[] = { 3503 { 1, 0x20, "ClrHubFeat" }, 3504 { 1, 0x23, "ClrPortFeat" }, 3505 { 2, 0xa3, "GetBusState" }, 3506 { 6, 0xa0, "GetHubDesc" }, 3507 { 0, 0xa0, "GetHubStat" }, 3508 { 0, 0xa3, "GetPortStat" }, 3509 { 7, 0x20, "SetHubDesc" }, 3510 { 3, 0x20, "SetHubFeat" }, 3511 { 3, 0x23, "SetPortFeat" }, 3512 {-1, 0, NULL}, 3513 }; 3514 int i; 3515 int value, index, len; 3516 const char *str; 3517 3518 value = UGETW(r->wValue); 3519 index = UGETW(r->wIndex); 3520 len = UGETW(r->wLength); 3521 for (i = 0; ; i++) { 3522 if (conf[i].req == -1 ) { 3523 slhci_log_req(r); 3524 return; 3525 } 3526 if (r->bmRequestType == conf[i].type && r->bRequest == conf[i].req) { 3527 str = conf[i].str; 3528 break; 3529 } 3530 } 3531 DDOLOG("hub request: %s v=%d,i=%d,l=%d ", str, value, index, len); 3532 } 3533 3534 void 3535 slhci_log_dumpreg(void) 3536 { 3537 uint8_t r; 3538 unsigned int aaddr, alen, baddr, blen; 3539 static u_char buf[240]; 3540 3541 r = slhci_read(ssc, SL11_E0CTRL); 3542 DDOLOG("USB A Host Control = %#.2x", r, 0,0,0); 3543 DDOLOGFLAG8("E0CTRL=", r, "Preamble", "Data Toggle", "SOF Sync", 3544 "ISOC", "res", "Out", "Enable", "Arm"); 3545 aaddr = slhci_read(ssc, SL11_E0ADDR); 3546 DDOLOG("USB A Base Address = %u", aaddr, 0,0,0); 3547 alen = slhci_read(ssc, SL11_E0LEN); 3548 DDOLOG("USB A Length = %u", alen, 0,0,0); 3549 r = slhci_read(ssc, SL11_E0STAT); 3550 DDOLOG("USB A Status = %#.2x", r, 0,0,0); 3551 DDOLOGFLAG8("E0STAT=", r, "STALL", "NAK", "Overflow", "Setup", 3552 "Data Toggle", "Timeout", "Error", "ACK"); 3553 r = slhci_read(ssc, SL11_E0CONT); 3554 DDOLOG("USB A Remaining or Overflow Length = %u", r, 0,0,0); 3555 r = slhci_read(ssc, SL11_E1CTRL); 3556 DDOLOG("USB B Host Control = %#.2x", r, 0,0,0); 3557 DDOLOGFLAG8("E1CTRL=", r, "Preamble", "Data Toggle", "SOF Sync", 3558 "ISOC", "res", "Out", "Enable", "Arm"); 3559 baddr = slhci_read(ssc, SL11_E1ADDR); 3560 DDOLOG("USB B Base Address = %u", baddr, 0,0,0); 3561 blen = slhci_read(ssc, SL11_E1LEN); 3562 DDOLOG("USB B Length = %u", blen, 0,0,0); 3563 r = slhci_read(ssc, SL11_E1STAT); 3564 DDOLOG("USB B Status = %#.2x", r, 0,0,0); 3565 DDOLOGFLAG8("E1STAT=", r, "STALL", "NAK", "Overflow", "Setup", 3566 "Data Toggle", "Timeout", "Error", "ACK"); 3567 r = slhci_read(ssc, SL11_E1CONT); 3568 DDOLOG("USB B Remaining or Overflow Length = %u", r, 0,0,0); 3569 3570 r = slhci_read(ssc, SL11_CTRL); 3571 DDOLOG("Control = %#.2x", r, 0,0,0); 3572 DDOLOGFLAG8("CTRL=", r, "res", "Suspend", "LOW Speed", 3573 "J-K State Force", "Reset", "res", "res", "SOF"); 3574 r = slhci_read(ssc, SL11_IER); 3575 DDOLOG("Interrupt Enable = %#.2x", r, 0,0,0); 3576 DDOLOGFLAG8("IER=", r, "D+ **IER!**", "Device Detect/Resume", 3577 "Insert/Remove", "SOF", "res", "res", "USBB", "USBA"); 3578 r = slhci_read(ssc, SL11_ISR); 3579 DDOLOG("Interrupt Status = %#.2x", r, 0,0,0); 3580 DDOLOGFLAG8("ISR=", r, "D+", "Device Detect/Resume", 3581 "Insert/Remove", "SOF", "res", "res", "USBB", "USBA"); 3582 r = slhci_read(ssc, SL11_REV); 3583 DDOLOG("Revision = %#.2x", r, 0,0,0); 3584 r = slhci_read(ssc, SL811_CSOF); 3585 DDOLOG("SOF Counter = %#.2x", r, 0,0,0); 3586 3587 if (alen && aaddr >= SL11_BUFFER_START && aaddr < SL11_BUFFER_END && 3588 alen <= SL11_MAX_PACKET_SIZE && aaddr + alen <= SL11_BUFFER_END) { 3589 slhci_read_multi(ssc, aaddr, buf, alen); 3590 DDOLOG("USBA Buffer: start %u len %u", aaddr, alen, 0,0); 3591 DDOLOGBUF(buf, alen); 3592 } else if (alen) 3593 DDOLOG("USBA Buffer Invalid", 0,0,0,0); 3594 3595 if (blen && baddr >= SL11_BUFFER_START && baddr < SL11_BUFFER_END && 3596 blen <= SL11_MAX_PACKET_SIZE && baddr + blen <= SL11_BUFFER_END) { 3597 slhci_read_multi(ssc, baddr, buf, blen); 3598 DDOLOG("USBB Buffer: start %u len %u", baddr, blen, 0,0); 3599 DDOLOGBUF(buf, blen); 3600 } else if (blen) 3601 DDOLOG("USBB Buffer Invalid", 0,0,0,0); 3602 } 3603 3604 void 3605 slhci_log_xfer(struct usbd_xfer *xfer) 3606 { 3607 DDOLOG("xfer: length=%u, actlen=%u, flags=%#x, timeout=%u,", 3608 xfer->length, xfer->actlen, xfer->flags, xfer->timeout); 3609 if (xfer->dmabuf.block) 3610 DDOLOG("buffer=%p", KERNADDR(&xfer->dmabuf, 0), 0,0,0); 3611 slhci_log_req_hub(&xfer->request); 3612 } 3613 3614 void 3615 slhci_log_spipe(struct slhci_pipe *spipe) 3616 { 3617 DDOLOG("spipe %p onlists: %s %s %s", spipe, gcq_onlist(&spipe->ap) ? 3618 "AP" : "", gcq_onlist(&spipe->to) ? "TO" : "", 3619 gcq_onlist(&spipe->xq) ? "XQ" : ""); 3620 DDOLOG("spipe: xfer %p buffer %p pflags %#x ptype %s", 3621 spipe->xfer, spipe->buffer, spipe->pflags, pnames(spipe->ptype)); 3622 } 3623 3624 void 3625 slhci_print_intr(void) 3626 { 3627 unsigned int ier, isr; 3628 ier = slhci_read(ssc, SL11_IER); 3629 isr = slhci_read(ssc, SL11_ISR); 3630 printf("IER: %#x ISR: %#x \n", ier, isr); 3631 } 3632 3633 #if 0 3634 void 3635 slhci_log_sc(void) 3636 { 3637 struct slhci_transfers *t; 3638 int i; 3639 3640 t = &ssc->sc_transfers; 3641 3642 DDOLOG("Flags=%#x", t->flags, 0,0,0); 3643 DDOLOG("a = %p Alen=%d b = %p Blen=%d", t->spipe[0], t->len[0], 3644 t->spipe[1], t->len[1]); 3645 3646 for (i=0; i<=Q_MAX; i++) 3647 DDOLOG("Q %d: %p", i, gcq_first(&t->q[i]), 0,0); 3648 3649 DDOLOG("TIMED: %p", GCQ_ITEM(gcq_first(&t->to), 3650 struct slhci_pipe, to), 0,0,0); 3651 3652 DDOLOG("frame=%d rootintr=%p", t->frame, t->rootintr, 0,0); 3653 3654 DDOLOG("use_polling=%d intr_context=%d", ssc->sc_bus.use_polling, 3655 ssc->sc_bus.intr_context, 0,0); 3656 } 3657 3658 void 3659 slhci_log_slreq(struct slhci_pipe *r) 3660 { 3661 DDOLOG("next: %p", r->q.next.sqe_next, 0,0,0); 3662 DDOLOG("xfer: %p", r->xfer, 0,0,0); 3663 DDOLOG("buffer: %p", r->buffer, 0,0,0); 3664 DDOLOG("bustime: %u", r->bustime, 0,0,0); 3665 DDOLOG("control: %#x", r->control, 0,0,0); 3666 DDOLOGFLAG8("control=", r->control, "Preamble", "Data Toggle", 3667 "SOF Sync", "ISOC", "res", "Out", "Enable", "Arm"); 3668 DDOLOG("pid: %#x", r->tregs[PID], 0,0,0); 3669 DDOLOG("dev: %u", r->tregs[DEV], 0,0,0); 3670 DDOLOG("len: %u", r->tregs[LEN], 0,0,0); 3671 3672 if (r->xfer) 3673 slhci_log_xfer(r->xfer); 3674 } 3675 #endif 3676 #endif /* SLHCI_DEBUG */ 3677 /* End debug functions. */ 3678