1 /* $NetBSD: dp8390.c,v 1.52 2003/01/15 22:20:05 bouyer Exp $ */ 2 3 /* 4 * Device driver for National Semiconductor DS8390/WD83C690 based ethernet 5 * adapters. 6 * 7 * Copyright (c) 1994, 1995 Charles M. Hannum. All rights reserved. 8 * 9 * Copyright (C) 1993, David Greenman. This software may be used, modified, 10 * copied, distributed, and sold, in both source and binary form provided that 11 * the above copyright and these terms are retained. Under no circumstances is 12 * the author responsible for the proper functioning of this software, nor does 13 * the author assume any responsibility for damages incurred with its use. 14 */ 15 16 #include <sys/cdefs.h> 17 __KERNEL_RCSID(0, "$NetBSD: dp8390.c,v 1.52 2003/01/15 22:20:05 bouyer Exp $"); 18 19 #include "opt_ipkdb.h" 20 #include "opt_inet.h" 21 #include "opt_ns.h" 22 #include "bpfilter.h" 23 #include "rnd.h" 24 25 #include <sys/param.h> 26 #include <sys/systm.h> 27 #include <sys/device.h> 28 #include <sys/errno.h> 29 #include <sys/ioctl.h> 30 #include <sys/mbuf.h> 31 #include <sys/socket.h> 32 #include <sys/syslog.h> 33 34 #if NRND > 0 35 #include <sys/rnd.h> 36 #endif 37 38 #include <net/if.h> 39 #include <net/if_dl.h> 40 #include <net/if_types.h> 41 #include <net/if_media.h> 42 #include <net/if_ether.h> 43 44 #ifdef INET 45 #include <netinet/in.h> 46 #include <netinet/in_systm.h> 47 #include <netinet/in_var.h> 48 #include <netinet/ip.h> 49 #include <netinet/if_inarp.h> 50 #endif 51 52 #ifdef NS 53 #include <netns/ns.h> 54 #include <netns/ns_if.h> 55 #endif 56 57 #if NBPFILTER > 0 58 #include <net/bpf.h> 59 #include <net/bpfdesc.h> 60 #endif 61 62 #include <machine/bus.h> 63 64 #ifdef IPKDB_DP8390 65 #include <ipkdb/ipkdb.h> 66 #endif 67 68 #include <dev/ic/dp8390reg.h> 69 #include <dev/ic/dp8390var.h> 70 71 #ifdef DEBUG 72 #define __inline__ /* XXX for debugging porpoises */ 73 int dp8390_debug = 0; 74 #endif 75 76 static __inline__ void dp8390_xmit __P((struct dp8390_softc *)); 77 78 static __inline__ void dp8390_read_hdr __P((struct dp8390_softc *, 79 int, struct dp8390_ring *)); 80 static __inline__ int dp8390_ring_copy __P((struct dp8390_softc *, 81 int, caddr_t, u_short)); 82 static __inline__ int dp8390_write_mbuf __P((struct dp8390_softc *, 83 struct mbuf *, int)); 84 85 static int dp8390_test_mem __P((struct dp8390_softc *)); 86 87 /* 88 * Standard media init routine for the dp8390. 89 */ 90 void 91 dp8390_media_init(struct dp8390_softc *sc) 92 { 93 94 ifmedia_init(&sc->sc_media, 0, dp8390_mediachange, dp8390_mediastatus); 95 ifmedia_add(&sc->sc_media, IFM_ETHER|IFM_MANUAL, 0, NULL); 96 ifmedia_set(&sc->sc_media, IFM_ETHER|IFM_MANUAL); 97 } 98 99 /* 100 * Do bus-independent setup. 101 */ 102 int 103 dp8390_config(sc) 104 struct dp8390_softc *sc; 105 { 106 struct ifnet *ifp = &sc->sc_ec.ec_if; 107 int rv; 108 109 rv = 1; 110 111 if (!sc->test_mem) 112 sc->test_mem = dp8390_test_mem; 113 114 /* Allocate one xmit buffer if < 16k, two buffers otherwise. */ 115 if ((sc->mem_size < 16384) || 116 (sc->sc_flags & DP8390_NO_MULTI_BUFFERING)) 117 sc->txb_cnt = 1; 118 else if (sc->mem_size < 8192 * 3) 119 sc->txb_cnt = 2; 120 else 121 sc->txb_cnt = 3; 122 123 sc->tx_page_start = sc->mem_start >> ED_PAGE_SHIFT; 124 sc->rec_page_start = sc->tx_page_start + sc->txb_cnt * ED_TXBUF_SIZE; 125 sc->rec_page_stop = sc->tx_page_start + (sc->mem_size >> ED_PAGE_SHIFT); 126 sc->mem_ring = sc->mem_start + (sc->rec_page_start << ED_PAGE_SHIFT); 127 sc->mem_end = sc->mem_start + sc->mem_size; 128 129 /* Now zero memory and verify that it is clear. */ 130 if ((*sc->test_mem)(sc)) 131 goto out; 132 133 /* Set interface to stopped condition (reset). */ 134 dp8390_stop(sc); 135 136 /* Initialize ifnet structure. */ 137 strcpy(ifp->if_xname, sc->sc_dev.dv_xname); 138 ifp->if_softc = sc; 139 ifp->if_start = dp8390_start; 140 ifp->if_ioctl = dp8390_ioctl; 141 if (!ifp->if_watchdog) 142 ifp->if_watchdog = dp8390_watchdog; 143 ifp->if_flags = 144 IFF_BROADCAST | IFF_SIMPLEX | IFF_NOTRAILERS | IFF_MULTICAST; 145 IFQ_SET_READY(&ifp->if_snd); 146 147 /* Print additional info when attached. */ 148 printf("%s: Ethernet address %s\n", sc->sc_dev.dv_xname, 149 ether_sprintf(sc->sc_enaddr)); 150 151 /* Initialize media goo. */ 152 (*sc->sc_media_init)(sc); 153 154 /* 155 * We can support 802.1Q VLAN-sized frames. 156 */ 157 sc->sc_ec.ec_capabilities |= ETHERCAP_VLAN_MTU; 158 159 /* Attach the interface. */ 160 if_attach(ifp); 161 ether_ifattach(ifp, sc->sc_enaddr); 162 163 #if NRND > 0 164 rnd_attach_source(&sc->rnd_source, sc->sc_dev.dv_xname, 165 RND_TYPE_NET, 0); 166 #endif 167 168 /* The attach is successful. */ 169 sc->sc_flags |= DP8390_ATTACHED; 170 171 rv = 0; 172 out: 173 return (rv); 174 } 175 176 /* 177 * Media change callback. 178 */ 179 int 180 dp8390_mediachange(ifp) 181 struct ifnet *ifp; 182 { 183 struct dp8390_softc *sc = ifp->if_softc; 184 185 if (sc->sc_mediachange) 186 return ((*sc->sc_mediachange)(sc)); 187 return (0); 188 } 189 190 /* 191 * Media status callback. 192 */ 193 void 194 dp8390_mediastatus(ifp, ifmr) 195 struct ifnet *ifp; 196 struct ifmediareq *ifmr; 197 { 198 struct dp8390_softc *sc = ifp->if_softc; 199 200 if (sc->sc_enabled == 0) { 201 ifmr->ifm_active = IFM_ETHER | IFM_NONE; 202 ifmr->ifm_status = 0; 203 return; 204 } 205 206 if (sc->sc_mediastatus) 207 (*sc->sc_mediastatus)(sc, ifmr); 208 } 209 210 /* 211 * Reset interface. 212 */ 213 void 214 dp8390_reset(sc) 215 struct dp8390_softc *sc; 216 { 217 int s; 218 219 s = splnet(); 220 dp8390_stop(sc); 221 dp8390_init(sc); 222 splx(s); 223 } 224 225 /* 226 * Take interface offline. 227 */ 228 void 229 dp8390_stop(sc) 230 struct dp8390_softc *sc; 231 { 232 bus_space_tag_t regt = sc->sc_regt; 233 bus_space_handle_t regh = sc->sc_regh; 234 int n = 5000; 235 236 /* Stop everything on the interface, and select page 0 registers. */ 237 NIC_BARRIER(regt, regh); 238 NIC_PUT(regt, regh, ED_P0_CR, 239 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); 240 NIC_BARRIER(regt, regh); 241 242 /* 243 * Wait for interface to enter stopped state, but limit # of checks to 244 * 'n' (about 5ms). It shouldn't even take 5us on modern DS8390's, but 245 * just in case it's an old one. 246 */ 247 while (((NIC_GET(regt, regh, 248 ED_P0_ISR) & ED_ISR_RST) == 0) && --n) 249 DELAY(1); 250 251 if (sc->stop_card != NULL) 252 (*sc->stop_card)(sc); 253 } 254 255 /* 256 * Device timeout/watchdog routine. Entered if the device neglects to generate 257 * an interrupt after a transmit has been started on it. 258 */ 259 260 void 261 dp8390_watchdog(ifp) 262 struct ifnet *ifp; 263 { 264 struct dp8390_softc *sc = ifp->if_softc; 265 266 log(LOG_ERR, "%s: device timeout\n", sc->sc_dev.dv_xname); 267 ++sc->sc_ec.ec_if.if_oerrors; 268 269 dp8390_reset(sc); 270 } 271 272 /* 273 * Initialize device. 274 */ 275 void 276 dp8390_init(sc) 277 struct dp8390_softc *sc; 278 { 279 bus_space_tag_t regt = sc->sc_regt; 280 bus_space_handle_t regh = sc->sc_regh; 281 struct ifnet *ifp = &sc->sc_ec.ec_if; 282 u_int8_t mcaf[8]; 283 int i; 284 285 /* 286 * Initialize the NIC in the exact order outlined in the NS manual. 287 * This init procedure is "mandatory"...don't change what or when 288 * things happen. 289 */ 290 291 /* Reset transmitter flags. */ 292 ifp->if_timer = 0; 293 294 sc->txb_inuse = 0; 295 sc->txb_new = 0; 296 sc->txb_next_tx = 0; 297 298 /* Set interface for page 0, remote DMA complete, stopped. */ 299 NIC_BARRIER(regt, regh); 300 NIC_PUT(regt, regh, ED_P0_CR, 301 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); 302 NIC_BARRIER(regt, regh); 303 304 if (sc->dcr_reg & ED_DCR_LS) { 305 NIC_PUT(regt, regh, ED_P0_DCR, sc->dcr_reg); 306 } else { 307 /* 308 * Set FIFO threshold to 8, No auto-init Remote DMA, byte 309 * order=80x86, byte-wide DMA xfers, 310 */ 311 NIC_PUT(regt, regh, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_LS); 312 } 313 314 /* Clear remote byte count registers. */ 315 NIC_PUT(regt, regh, ED_P0_RBCR0, 0); 316 NIC_PUT(regt, regh, ED_P0_RBCR1, 0); 317 318 /* Tell RCR to do nothing for now. */ 319 NIC_PUT(regt, regh, ED_P0_RCR, ED_RCR_MON | sc->rcr_proto); 320 321 /* Place NIC in internal loopback mode. */ 322 NIC_PUT(regt, regh, ED_P0_TCR, ED_TCR_LB0); 323 324 /* Set lower bits of byte addressable framing to 0. */ 325 if (sc->is790) 326 NIC_PUT(regt, regh, 0x09, 0); 327 328 /* Initialize receive buffer ring. */ 329 NIC_PUT(regt, regh, ED_P0_BNRY, sc->rec_page_start); 330 NIC_PUT(regt, regh, ED_P0_PSTART, sc->rec_page_start); 331 NIC_PUT(regt, regh, ED_P0_PSTOP, sc->rec_page_stop); 332 333 /* 334 * Enable the following interrupts: receive/transmit complete, 335 * receive/transmit error, and Receiver OverWrite. 336 * 337 * Counter overflow and Remote DMA complete are *not* enabled. 338 */ 339 NIC_PUT(regt, regh, ED_P0_IMR, 340 ED_IMR_PRXE | ED_IMR_PTXE | ED_IMR_RXEE | ED_IMR_TXEE | 341 ED_IMR_OVWE); 342 343 /* 344 * Clear all interrupts. A '1' in each bit position clears the 345 * corresponding flag. 346 */ 347 NIC_PUT(regt, regh, ED_P0_ISR, 0xff); 348 349 /* Program command register for page 1. */ 350 NIC_BARRIER(regt, regh); 351 NIC_PUT(regt, regh, ED_P0_CR, 352 sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STP); 353 NIC_BARRIER(regt, regh); 354 355 /* Copy out our station address. */ 356 for (i = 0; i < ETHER_ADDR_LEN; ++i) 357 NIC_PUT(regt, regh, ED_P1_PAR0 + i, 358 LLADDR(ifp->if_sadl)[i]); 359 360 /* Set multicast filter on chip. */ 361 dp8390_getmcaf(&sc->sc_ec, mcaf); 362 for (i = 0; i < 8; i++) 363 NIC_PUT(regt, regh, ED_P1_MAR0 + i, mcaf[i]); 364 365 /* 366 * Set current page pointer to one page after the boundary pointer, as 367 * recommended in the National manual. 368 */ 369 sc->next_packet = sc->rec_page_start + 1; 370 NIC_PUT(regt, regh, ED_P1_CURR, sc->next_packet); 371 372 /* Program command register for page 0. */ 373 NIC_BARRIER(regt, regh); 374 NIC_PUT(regt, regh, ED_P1_CR, 375 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); 376 NIC_BARRIER(regt, regh); 377 378 /* Accept broadcast and multicast packets by default. */ 379 i = ED_RCR_AB | ED_RCR_AM | sc->rcr_proto; 380 if (ifp->if_flags & IFF_PROMISC) { 381 /* 382 * Set promiscuous mode. Multicast filter was set earlier so 383 * that we should receive all multicast packets. 384 */ 385 i |= ED_RCR_PRO | ED_RCR_AR | ED_RCR_SEP; 386 } 387 NIC_PUT(regt, regh, ED_P0_RCR, i); 388 389 /* Take interface out of loopback. */ 390 NIC_PUT(regt, regh, ED_P0_TCR, 0); 391 392 /* Do any card-specific initialization, if applicable. */ 393 if (sc->init_card) 394 (*sc->init_card)(sc); 395 396 /* Fire up the interface. */ 397 NIC_BARRIER(regt, regh); 398 NIC_PUT(regt, regh, ED_P0_CR, 399 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 400 401 /* Set 'running' flag, and clear output active flag. */ 402 ifp->if_flags |= IFF_RUNNING; 403 ifp->if_flags &= ~IFF_OACTIVE; 404 405 /* ...and attempt to start output. */ 406 dp8390_start(ifp); 407 } 408 409 /* 410 * This routine actually starts the transmission on the interface. 411 */ 412 static __inline__ void 413 dp8390_xmit(sc) 414 struct dp8390_softc *sc; 415 { 416 bus_space_tag_t regt = sc->sc_regt; 417 bus_space_handle_t regh = sc->sc_regh; 418 struct ifnet *ifp = &sc->sc_ec.ec_if; 419 u_short len; 420 421 #ifdef DIAGNOSTIC 422 if ((sc->txb_next_tx + sc->txb_inuse) % sc->txb_cnt != sc->txb_new) 423 panic("dp8390_xmit: desync, next_tx=%d inuse=%d cnt=%d new=%d", 424 sc->txb_next_tx, sc->txb_inuse, sc->txb_cnt, sc->txb_new); 425 426 if (sc->txb_inuse == 0) 427 panic("dp8390_xmit: no packets to xmit"); 428 #endif 429 430 len = sc->txb_len[sc->txb_next_tx]; 431 432 /* Set NIC for page 0 register access. */ 433 NIC_BARRIER(regt, regh); 434 NIC_PUT(regt, regh, ED_P0_CR, 435 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 436 NIC_BARRIER(regt, regh); 437 438 /* Set TX buffer start page. */ 439 NIC_PUT(regt, regh, ED_P0_TPSR, sc->tx_page_start + 440 sc->txb_next_tx * ED_TXBUF_SIZE); 441 442 /* Set TX length. */ 443 NIC_PUT(regt, regh, ED_P0_TBCR0, len); 444 NIC_PUT(regt, regh, ED_P0_TBCR1, len >> 8); 445 446 /* Set page 0, remote DMA complete, transmit packet, and *start*. */ 447 NIC_BARRIER(regt, regh); 448 NIC_PUT(regt, regh, ED_P0_CR, 449 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_TXP | ED_CR_STA); 450 451 /* Point to next transmit buffer slot and wrap if necessary. */ 452 if (++sc->txb_next_tx == sc->txb_cnt) 453 sc->txb_next_tx = 0; 454 455 /* Set a timer just in case we never hear from the board again. */ 456 ifp->if_timer = 2; 457 } 458 459 /* 460 * Start output on interface. 461 * We make two assumptions here: 462 * 1) that the current priority is set to splnet _before_ this code 463 * is called *and* is returned to the appropriate priority after 464 * return 465 * 2) that the IFF_OACTIVE flag is checked before this code is called 466 * (i.e. that the output part of the interface is idle) 467 */ 468 void 469 dp8390_start(ifp) 470 struct ifnet *ifp; 471 { 472 struct dp8390_softc *sc = ifp->if_softc; 473 struct mbuf *m0; 474 int buffer; 475 int len; 476 477 if ((ifp->if_flags & (IFF_RUNNING | IFF_OACTIVE)) != IFF_RUNNING) 478 return; 479 480 outloop: 481 /* See if there is room to put another packet in the buffer. */ 482 if (sc->txb_inuse == sc->txb_cnt) { 483 /* No room. Indicate this to the outside world and exit. */ 484 ifp->if_flags |= IFF_OACTIVE; 485 return; 486 } 487 IFQ_DEQUEUE(&ifp->if_snd, m0); 488 if (m0 == 0) 489 return; 490 491 /* We need to use m->m_pkthdr.len, so require the header */ 492 if ((m0->m_flags & M_PKTHDR) == 0) 493 panic("dp8390_start: no header mbuf"); 494 495 #if NBPFILTER > 0 496 /* Tap off here if there is a BPF listener. */ 497 if (ifp->if_bpf) 498 bpf_mtap(ifp->if_bpf, m0); 499 #endif 500 501 /* txb_new points to next open buffer slot. */ 502 buffer = sc->mem_start + 503 ((sc->txb_new * ED_TXBUF_SIZE) << ED_PAGE_SHIFT); 504 505 if (sc->write_mbuf) 506 len = (*sc->write_mbuf)(sc, m0, buffer); 507 else 508 len = dp8390_write_mbuf(sc, m0, buffer); 509 510 m_freem(m0); 511 sc->txb_len[sc->txb_new] = len; 512 513 /* Point to next buffer slot and wrap if necessary. */ 514 if (++sc->txb_new == sc->txb_cnt) 515 sc->txb_new = 0; 516 517 /* Start the first packet transmitting. */ 518 if (sc->txb_inuse++ == 0) 519 dp8390_xmit(sc); 520 521 /* Loop back to the top to possibly buffer more packets. */ 522 goto outloop; 523 } 524 525 /* 526 * Ethernet interface receiver interrupt. 527 */ 528 void 529 dp8390_rint(sc) 530 struct dp8390_softc *sc; 531 { 532 bus_space_tag_t regt = sc->sc_regt; 533 bus_space_handle_t regh = sc->sc_regh; 534 struct dp8390_ring packet_hdr; 535 int packet_ptr; 536 u_short len; 537 u_char boundary, current; 538 u_char nlen; 539 540 loop: 541 /* Set NIC to page 1 registers to get 'current' pointer. */ 542 NIC_BARRIER(regt, regh); 543 NIC_PUT(regt, regh, ED_P0_CR, 544 sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STA); 545 NIC_BARRIER(regt, regh); 546 547 /* 548 * 'sc->next_packet' is the logical beginning of the ring-buffer - i.e. 549 * it points to where new data has been buffered. The 'CURR' (current) 550 * register points to the logical end of the ring-buffer - i.e. it 551 * points to where additional new data will be added. We loop here 552 * until the logical beginning equals the logical end (or in other 553 * words, until the ring-buffer is empty). 554 */ 555 current = NIC_GET(regt, regh, ED_P1_CURR); 556 if (sc->next_packet == current) 557 return; 558 559 /* Set NIC to page 0 registers to update boundary register. */ 560 NIC_BARRIER(regt, regh); 561 NIC_PUT(regt, regh, ED_P1_CR, 562 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 563 NIC_BARRIER(regt, regh); 564 565 do { 566 /* Get pointer to this buffer's header structure. */ 567 packet_ptr = sc->mem_ring + 568 ((sc->next_packet - sc->rec_page_start) << ED_PAGE_SHIFT); 569 570 if (sc->read_hdr) 571 (*sc->read_hdr)(sc, packet_ptr, &packet_hdr); 572 else 573 dp8390_read_hdr(sc, packet_ptr, &packet_hdr); 574 len = packet_hdr.count; 575 576 /* 577 * Try do deal with old, buggy chips that sometimes duplicate 578 * the low byte of the length into the high byte. We do this 579 * by simply ignoring the high byte of the length and always 580 * recalculating it. 581 * 582 * NOTE: sc->next_packet is pointing at the current packet. 583 */ 584 if (packet_hdr.next_packet >= sc->next_packet) 585 nlen = (packet_hdr.next_packet - sc->next_packet); 586 else 587 nlen = ((packet_hdr.next_packet - sc->rec_page_start) + 588 (sc->rec_page_stop - sc->next_packet)); 589 --nlen; 590 if ((len & ED_PAGE_MASK) + sizeof(packet_hdr) > ED_PAGE_SIZE) 591 --nlen; 592 len = (len & ED_PAGE_MASK) | (nlen << ED_PAGE_SHIFT); 593 #ifdef DIAGNOSTIC 594 if (len != packet_hdr.count) { 595 printf("%s: length does not match " 596 "next packet pointer\n", sc->sc_dev.dv_xname); 597 printf("%s: len %04x nlen %04x start %02x " 598 "first %02x curr %02x next %02x stop %02x\n", 599 sc->sc_dev.dv_xname, packet_hdr.count, len, 600 sc->rec_page_start, sc->next_packet, current, 601 packet_hdr.next_packet, sc->rec_page_stop); 602 } 603 #endif 604 605 /* 606 * Be fairly liberal about what we allow as a "reasonable" 607 * length so that a [crufty] packet will make it to BPF (and 608 * can thus be analyzed). Note that all that is really 609 * important is that we have a length that will fit into one 610 * mbuf cluster or less; the upper layer protocols can then 611 * figure out the length from their own length field(s). 612 */ 613 if (len <= MCLBYTES && 614 packet_hdr.next_packet >= sc->rec_page_start && 615 packet_hdr.next_packet < sc->rec_page_stop) { 616 /* Go get packet. */ 617 dp8390_read(sc, 618 packet_ptr + sizeof(struct dp8390_ring), 619 len - sizeof(struct dp8390_ring)); 620 ++sc->sc_ec.ec_if.if_ipackets; 621 } else { 622 /* Really BAD. The ring pointers are corrupted. */ 623 log(LOG_ERR, "%s: NIC memory corrupt - " 624 "invalid packet length %d\n", 625 sc->sc_dev.dv_xname, len); 626 ++sc->sc_ec.ec_if.if_ierrors; 627 dp8390_reset(sc); 628 return; 629 } 630 631 /* Update next packet pointer. */ 632 sc->next_packet = packet_hdr.next_packet; 633 634 /* 635 * Update NIC boundary pointer - being careful to keep it one 636 * buffer behind (as recommended by NS databook). 637 */ 638 boundary = sc->next_packet - 1; 639 if (boundary < sc->rec_page_start) 640 boundary = sc->rec_page_stop - 1; 641 NIC_PUT(regt, regh, ED_P0_BNRY, boundary); 642 } while (sc->next_packet != current); 643 644 goto loop; 645 } 646 647 /* Ethernet interface interrupt processor. */ 648 int 649 dp8390_intr(arg) 650 void *arg; 651 { 652 struct dp8390_softc *sc = (struct dp8390_softc *)arg; 653 bus_space_tag_t regt = sc->sc_regt; 654 bus_space_handle_t regh = sc->sc_regh; 655 struct ifnet *ifp = &sc->sc_ec.ec_if; 656 u_char isr; 657 #if NRND > 0 658 u_char rndisr; 659 #endif 660 661 if (sc->sc_enabled == 0 || 662 (sc->sc_dev.dv_flags & DVF_ACTIVE) == 0) 663 return (0); 664 665 /* Set NIC to page 0 registers. */ 666 NIC_BARRIER(regt, regh); 667 NIC_PUT(regt, regh, ED_P0_CR, 668 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 669 NIC_BARRIER(regt, regh); 670 671 isr = NIC_GET(regt, regh, ED_P0_ISR); 672 if (!isr) 673 return (0); 674 675 #if NRND > 0 676 rndisr = isr; 677 #endif 678 679 /* Loop until there are no more new interrupts. */ 680 for (;;) { 681 /* 682 * Reset all the bits that we are 'acknowledging' by writing a 683 * '1' to each bit position that was set. 684 * (Writing a '1' *clears* the bit.) 685 */ 686 NIC_PUT(regt, regh, ED_P0_ISR, isr); 687 688 /* Work around for AX88190 bug */ 689 if ((sc->sc_flags & DP8390_DO_AX88190_WORKAROUND) != 0) 690 while ((NIC_GET(regt, regh, ED_P0_ISR) & isr) != 0) { 691 NIC_PUT(regt, regh, ED_P0_ISR, 0); 692 NIC_PUT(regt, regh, ED_P0_ISR, isr); 693 } 694 695 /* 696 * Handle transmitter interrupts. Handle these first because 697 * the receiver will reset the board under some conditions. 698 * 699 * If the chip was reset while a packet was transmitting, it 700 * may still deliver a TX interrupt. In this case, just ignore 701 * the interrupt. 702 */ 703 if (isr & (ED_ISR_PTX | ED_ISR_TXE) && 704 sc->txb_inuse != 0) { 705 u_char collisions = 706 NIC_GET(regt, regh, ED_P0_NCR) & 0x0f; 707 708 /* 709 * Check for transmit error. If a TX completed with an 710 * error, we end up throwing the packet away. Really 711 * the only error that is possible is excessive 712 * collisions, and in this case it is best to allow the 713 * automatic mechanisms of TCP to backoff the flow. Of 714 * course, with UDP we're screwed, but this is expected 715 * when a network is heavily loaded. 716 */ 717 if (isr & ED_ISR_TXE) { 718 /* 719 * Excessive collisions (16). 720 */ 721 if ((NIC_GET(regt, regh, ED_P0_TSR) 722 & ED_TSR_ABT) && (collisions == 0)) { 723 /* 724 * When collisions total 16, the P0_NCR 725 * will indicate 0, and the TSR_ABT is 726 * set. 727 */ 728 collisions = 16; 729 } 730 731 /* Update output errors counter. */ 732 ++ifp->if_oerrors; 733 } else { 734 /* 735 * Throw away the non-error status bits. 736 * 737 * XXX 738 * It may be useful to detect loss of carrier 739 * and late collisions here. 740 */ 741 (void)NIC_GET(regt, regh, ED_P0_TSR); 742 743 /* 744 * Update total number of successfully 745 * transmitted packets. 746 */ 747 ++ifp->if_opackets; 748 } 749 750 /* Clear watchdog timer. */ 751 ifp->if_timer = 0; 752 ifp->if_flags &= ~IFF_OACTIVE; 753 754 /* 755 * Add in total number of collisions on last 756 * transmission. 757 */ 758 ifp->if_collisions += collisions; 759 760 /* 761 * Decrement buffer in-use count if not zero (can only 762 * be zero if a transmitter interrupt occurred while not 763 * actually transmitting). 764 * If data is ready to transmit, start it transmitting, 765 * otherwise defer until after handling receiver. 766 */ 767 if (--sc->txb_inuse != 0) 768 dp8390_xmit(sc); 769 } 770 771 /* Handle receiver interrupts. */ 772 if (isr & (ED_ISR_PRX | ED_ISR_RXE | ED_ISR_OVW)) { 773 /* 774 * Overwrite warning. In order to make sure that a 775 * lockup of the local DMA hasn't occurred, we reset 776 * and re-init the NIC. The NSC manual suggests only a 777 * partial reset/re-init is necessary - but some chips 778 * seem to want more. The DMA lockup has been seen 779 * only with early rev chips - Methinks this bug was 780 * fixed in later revs. -DG 781 */ 782 if (isr & ED_ISR_OVW) { 783 ++ifp->if_ierrors; 784 #ifdef DIAGNOSTIC 785 log(LOG_WARNING, "%s: warning - receiver " 786 "ring buffer overrun\n", 787 sc->sc_dev.dv_xname); 788 #endif 789 /* Stop/reset/re-init NIC. */ 790 dp8390_reset(sc); 791 } else { 792 /* 793 * Receiver Error. One or more of: CRC error, 794 * frame alignment error FIFO overrun, or 795 * missed packet. 796 */ 797 if (isr & ED_ISR_RXE) { 798 ++ifp->if_ierrors; 799 #ifdef DEBUG 800 if (dp8390_debug) { 801 printf("%s: receive error %x\n", 802 sc->sc_dev.dv_xname, 803 NIC_GET(regt, regh, 804 ED_P0_RSR)); 805 } 806 #endif 807 } 808 809 /* 810 * Go get the packet(s) 811 * XXX - Doing this on an error is dubious 812 * because there shouldn't be any data to get 813 * (we've configured the interface to not 814 * accept packets with errors). 815 */ 816 if (sc->recv_int) 817 (*sc->recv_int)(sc); 818 else 819 dp8390_rint(sc); 820 } 821 } 822 823 /* 824 * If it looks like the transmitter can take more data, attempt 825 * to start output on the interface. This is done after 826 * handling the receiver to give the receiver priority. 827 */ 828 dp8390_start(ifp); 829 830 /* 831 * Return NIC CR to standard state: page 0, remote DMA 832 * complete, start (toggling the TXP bit off, even if was just 833 * set in the transmit routine, is *okay* - it is 'edge' 834 * triggered from low to high). 835 */ 836 NIC_BARRIER(regt, regh); 837 NIC_PUT(regt, regh, ED_P0_CR, 838 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 839 NIC_BARRIER(regt, regh); 840 841 /* 842 * If the Network Talley Counters overflow, read them to reset 843 * them. It appears that old 8390's won't clear the ISR flag 844 * otherwise - resulting in an infinite loop. 845 */ 846 if (isr & ED_ISR_CNT) { 847 (void)NIC_GET(regt, regh, ED_P0_CNTR0); 848 (void)NIC_GET(regt, regh, ED_P0_CNTR1); 849 (void)NIC_GET(regt, regh, ED_P0_CNTR2); 850 } 851 852 isr = NIC_GET(regt, regh, ED_P0_ISR); 853 if (!isr) 854 goto out; 855 } 856 857 out: 858 #if NRND > 0 859 rnd_add_uint32(&sc->rnd_source, rndisr); 860 #endif 861 return (1); 862 } 863 864 /* 865 * Process an ioctl request. This code needs some work - it looks pretty ugly. 866 */ 867 int 868 dp8390_ioctl(ifp, cmd, data) 869 struct ifnet *ifp; 870 u_long cmd; 871 caddr_t data; 872 { 873 struct dp8390_softc *sc = ifp->if_softc; 874 struct ifaddr *ifa = (struct ifaddr *) data; 875 struct ifreq *ifr = (struct ifreq *) data; 876 int s, error = 0; 877 878 s = splnet(); 879 880 switch (cmd) { 881 882 case SIOCSIFADDR: 883 if ((error = dp8390_enable(sc)) != 0) 884 break; 885 ifp->if_flags |= IFF_UP; 886 887 switch (ifa->ifa_addr->sa_family) { 888 #ifdef INET 889 case AF_INET: 890 dp8390_init(sc); 891 arp_ifinit(ifp, ifa); 892 break; 893 #endif 894 #ifdef NS 895 /* XXX - This code is probably wrong. */ 896 case AF_NS: 897 { 898 struct ns_addr *ina = &IA_SNS(ifa)->sns_addr; 899 900 if (ns_nullhost(*ina)) 901 ina->x_host = 902 *(union ns_host *)LLADDR(ifp->if_sadl); 903 else 904 memcpy(LLADDR(ifp->if_sadl), 905 ina->x_host.c_host, ETHER_ADDR_LEN); 906 /* Set new address. */ 907 dp8390_init(sc); 908 break; 909 } 910 #endif 911 default: 912 dp8390_init(sc); 913 break; 914 } 915 break; 916 917 case SIOCSIFFLAGS: 918 if ((ifp->if_flags & IFF_UP) == 0 && 919 (ifp->if_flags & IFF_RUNNING) != 0) { 920 /* 921 * If interface is marked down and it is running, then 922 * stop it. 923 */ 924 dp8390_stop(sc); 925 ifp->if_flags &= ~IFF_RUNNING; 926 dp8390_disable(sc); 927 } else if ((ifp->if_flags & IFF_UP) != 0 && 928 (ifp->if_flags & IFF_RUNNING) == 0) { 929 /* 930 * If interface is marked up and it is stopped, then 931 * start it. 932 */ 933 if ((error = dp8390_enable(sc)) != 0) 934 break; 935 dp8390_init(sc); 936 } else if ((ifp->if_flags & IFF_UP) != 0) { 937 /* 938 * Reset the interface to pick up changes in any other 939 * flags that affect hardware registers. 940 */ 941 dp8390_stop(sc); 942 dp8390_init(sc); 943 } 944 break; 945 946 case SIOCADDMULTI: 947 case SIOCDELMULTI: 948 if (sc->sc_enabled == 0) { 949 error = EIO; 950 break; 951 } 952 953 /* Update our multicast list. */ 954 error = (cmd == SIOCADDMULTI) ? 955 ether_addmulti(ifr, &sc->sc_ec) : 956 ether_delmulti(ifr, &sc->sc_ec); 957 958 if (error == ENETRESET) { 959 /* 960 * Multicast list has changed; set the hardware filter 961 * accordingly. 962 */ 963 dp8390_stop(sc); /* XXX for ds_setmcaf? */ 964 dp8390_init(sc); 965 error = 0; 966 } 967 break; 968 969 case SIOCGIFMEDIA: 970 case SIOCSIFMEDIA: 971 error = ifmedia_ioctl(ifp, ifr, &sc->sc_media, cmd); 972 break; 973 974 default: 975 error = EINVAL; 976 break; 977 } 978 979 splx(s); 980 return (error); 981 } 982 983 /* 984 * Retrieve packet from buffer memory and send to the next level up via 985 * ether_input(). If there is a BPF listener, give a copy to BPF, too. 986 */ 987 void 988 dp8390_read(sc, buf, len) 989 struct dp8390_softc *sc; 990 int buf; 991 u_short len; 992 { 993 struct ifnet *ifp = &sc->sc_ec.ec_if; 994 struct mbuf *m; 995 996 /* Pull packet off interface. */ 997 m = dp8390_get(sc, buf, len); 998 if (m == 0) { 999 ifp->if_ierrors++; 1000 return; 1001 } 1002 1003 ifp->if_ipackets++; 1004 1005 #if NBPFILTER > 0 1006 /* 1007 * Check if there's a BPF listener on this interface. 1008 * If so, hand off the raw packet to bpf. 1009 */ 1010 if (ifp->if_bpf) 1011 bpf_mtap(ifp->if_bpf, m); 1012 #endif 1013 1014 (*ifp->if_input)(ifp, m); 1015 } 1016 1017 1018 /* 1019 * Supporting routines. 1020 */ 1021 1022 /* 1023 * Compute the multicast address filter from the list of multicast addresses we 1024 * need to listen to. 1025 */ 1026 void 1027 dp8390_getmcaf(ec, af) 1028 struct ethercom *ec; 1029 u_int8_t *af; 1030 { 1031 struct ifnet *ifp = &ec->ec_if; 1032 struct ether_multi *enm; 1033 u_int32_t crc; 1034 int i; 1035 struct ether_multistep step; 1036 1037 /* 1038 * Set up multicast address filter by passing all multicast addresses 1039 * through a crc generator, and then using the high order 6 bits as an 1040 * index into the 64 bit logical address filter. The high order bit 1041 * selects the word, while the rest of the bits select the bit within 1042 * the word. 1043 */ 1044 1045 if (ifp->if_flags & IFF_PROMISC) { 1046 ifp->if_flags |= IFF_ALLMULTI; 1047 for (i = 0; i < 8; i++) 1048 af[i] = 0xff; 1049 return; 1050 } 1051 for (i = 0; i < 8; i++) 1052 af[i] = 0; 1053 ETHER_FIRST_MULTI(step, ec, enm); 1054 while (enm != NULL) { 1055 if (memcmp(enm->enm_addrlo, enm->enm_addrhi, 1056 sizeof(enm->enm_addrlo)) != 0) { 1057 /* 1058 * We must listen to a range of multicast addresses. 1059 * For now, just accept all multicasts, rather than 1060 * trying to set only those filter bits needed to match 1061 * the range. (At this time, the only use of address 1062 * ranges is for IP multicast routing, for which the 1063 * range is big enough to require all bits set.) 1064 */ 1065 ifp->if_flags |= IFF_ALLMULTI; 1066 for (i = 0; i < 8; i++) 1067 af[i] = 0xff; 1068 return; 1069 } 1070 1071 crc = ether_crc32_be(enm->enm_addrlo, ETHER_ADDR_LEN); 1072 1073 /* Just want the 6 most significant bits. */ 1074 crc >>= 26; 1075 1076 /* Turn on the corresponding bit in the filter. */ 1077 af[crc >> 3] |= 1 << (crc & 0x7); 1078 1079 ETHER_NEXT_MULTI(step, enm); 1080 } 1081 ifp->if_flags &= ~IFF_ALLMULTI; 1082 } 1083 1084 /* 1085 * Copy data from receive buffer to a new mbuf chain allocating mbufs 1086 * as needed. Return pointer to first mbuf in chain. 1087 * sc = dp8390 info (softc) 1088 * src = pointer in dp8390 ring buffer 1089 * total_len = amount of data to copy 1090 */ 1091 struct mbuf * 1092 dp8390_get(sc, src, total_len) 1093 struct dp8390_softc *sc; 1094 int src; 1095 u_short total_len; 1096 { 1097 struct ifnet *ifp = &sc->sc_ec.ec_if; 1098 struct mbuf *m, *m0, *newm; 1099 u_short len; 1100 1101 MGETHDR(m0, M_DONTWAIT, MT_DATA); 1102 if (m0 == 0) 1103 return (0); 1104 m0->m_pkthdr.rcvif = ifp; 1105 m0->m_pkthdr.len = total_len; 1106 len = MHLEN; 1107 m = m0; 1108 1109 while (total_len > 0) { 1110 if (total_len >= MINCLSIZE) { 1111 MCLGET(m, M_DONTWAIT); 1112 if ((m->m_flags & M_EXT) == 0) 1113 goto bad; 1114 len = MCLBYTES; 1115 } 1116 1117 /* 1118 * Make sure the data after the Ethernet header is aligned. 1119 */ 1120 if (m == m0) { 1121 caddr_t newdata = (caddr_t) 1122 ALIGN(m->m_data + sizeof(struct ether_header)) - 1123 sizeof(struct ether_header); 1124 len -= newdata - m->m_data; 1125 m->m_data = newdata; 1126 } 1127 1128 m->m_len = len = min(total_len, len); 1129 if (sc->ring_copy) 1130 src = (*sc->ring_copy)(sc, src, mtod(m, caddr_t), len); 1131 else 1132 src = dp8390_ring_copy(sc, src, mtod(m, caddr_t), len); 1133 1134 total_len -= len; 1135 if (total_len > 0) { 1136 MGET(newm, M_DONTWAIT, MT_DATA); 1137 if (newm == 0) 1138 goto bad; 1139 len = MLEN; 1140 m = m->m_next = newm; 1141 } 1142 } 1143 1144 return (m0); 1145 1146 bad: 1147 m_freem(m0); 1148 return (0); 1149 } 1150 1151 1152 /* 1153 * Default driver support functions. 1154 * 1155 * NOTE: all support functions assume 8-bit shared memory. 1156 */ 1157 /* 1158 * Zero NIC buffer memory and verify that it is clear. 1159 */ 1160 static int 1161 dp8390_test_mem(sc) 1162 struct dp8390_softc *sc; 1163 { 1164 bus_space_tag_t buft = sc->sc_buft; 1165 bus_space_handle_t bufh = sc->sc_bufh; 1166 int i; 1167 1168 bus_space_set_region_1(buft, bufh, sc->mem_start, 0, sc->mem_size); 1169 1170 for (i = 0; i < sc->mem_size; ++i) { 1171 if (bus_space_read_1(buft, bufh, sc->mem_start + i)) { 1172 printf(": failed to clear NIC buffer at offset %x - " 1173 "check configuration\n", (sc->mem_start + i)); 1174 return 1; 1175 } 1176 } 1177 1178 return 0; 1179 } 1180 1181 /* 1182 * Read a packet header from the ring, given the source offset. 1183 */ 1184 static __inline__ void 1185 dp8390_read_hdr(sc, src, hdrp) 1186 struct dp8390_softc *sc; 1187 int src; 1188 struct dp8390_ring *hdrp; 1189 { 1190 bus_space_tag_t buft = sc->sc_buft; 1191 bus_space_handle_t bufh = sc->sc_bufh; 1192 1193 /* 1194 * The byte count includes a 4 byte header that was added by 1195 * the NIC. 1196 */ 1197 hdrp->rsr = bus_space_read_1(buft, bufh, src); 1198 hdrp->next_packet = bus_space_read_1(buft, bufh, src + 1); 1199 hdrp->count = bus_space_read_1(buft, bufh, src + 2) | 1200 (bus_space_read_1(buft, bufh, src + 3) << 8); 1201 } 1202 1203 /* 1204 * Copy `amount' bytes from a packet in the ring buffer to a linear 1205 * destination buffer, given a source offset and destination address. 1206 * Takes into account ring-wrap. 1207 */ 1208 static __inline__ int 1209 dp8390_ring_copy(sc, src, dst, amount) 1210 struct dp8390_softc *sc; 1211 int src; 1212 caddr_t dst; 1213 u_short amount; 1214 { 1215 bus_space_tag_t buft = sc->sc_buft; 1216 bus_space_handle_t bufh = sc->sc_bufh; 1217 u_short tmp_amount; 1218 1219 /* Does copy wrap to lower addr in ring buffer? */ 1220 if (src + amount > sc->mem_end) { 1221 tmp_amount = sc->mem_end - src; 1222 1223 /* Copy amount up to end of NIC memory. */ 1224 bus_space_read_region_1(buft, bufh, src, dst, tmp_amount); 1225 1226 amount -= tmp_amount; 1227 src = sc->mem_ring; 1228 dst += tmp_amount; 1229 } 1230 bus_space_read_region_1(buft, bufh, src, dst, amount); 1231 1232 return (src + amount); 1233 } 1234 1235 /* 1236 * Copy a packet from an mbuf to the transmit buffer on the card. 1237 * 1238 * Currently uses an extra buffer/extra memory copy, unless the whole 1239 * packet fits in one mbuf. 1240 */ 1241 static __inline__ int 1242 dp8390_write_mbuf(sc, m, buf) 1243 struct dp8390_softc *sc; 1244 struct mbuf *m; 1245 int buf; 1246 { 1247 bus_space_tag_t buft = sc->sc_buft; 1248 bus_space_handle_t bufh = sc->sc_bufh; 1249 u_char *data; 1250 int len, totlen = 0; 1251 1252 for (; m ; m = m->m_next) { 1253 data = mtod(m, u_char *); 1254 len = m->m_len; 1255 if (len > 0) { 1256 bus_space_write_region_1(buft, bufh, buf, data, len); 1257 totlen += len; 1258 buf += len; 1259 } 1260 } 1261 if (totlen < ETHER_MIN_LEN - ETHER_CRC_LEN) { 1262 bus_space_set_region_1(buft, bufh, buf, 0, 1263 ETHER_MIN_LEN - ETHER_CRC_LEN - totlen); 1264 totlen = ETHER_MIN_LEN - ETHER_CRC_LEN; 1265 } 1266 return (totlen); 1267 } 1268 1269 /* 1270 * Enable power on the interface. 1271 */ 1272 int 1273 dp8390_enable(sc) 1274 struct dp8390_softc *sc; 1275 { 1276 1277 if (sc->sc_enabled == 0 && sc->sc_enable != NULL) { 1278 if ((*sc->sc_enable)(sc) != 0) { 1279 printf("%s: device enable failed\n", 1280 sc->sc_dev.dv_xname); 1281 return (EIO); 1282 } 1283 } 1284 1285 sc->sc_enabled = 1; 1286 return (0); 1287 } 1288 1289 /* 1290 * Disable power on the interface. 1291 */ 1292 void 1293 dp8390_disable(sc) 1294 struct dp8390_softc *sc; 1295 { 1296 1297 if (sc->sc_enabled != 0 && sc->sc_disable != NULL) { 1298 (*sc->sc_disable)(sc); 1299 sc->sc_enabled = 0; 1300 } 1301 } 1302 1303 int 1304 dp8390_activate(self, act) 1305 struct device *self; 1306 enum devact act; 1307 { 1308 struct dp8390_softc *sc = (struct dp8390_softc *)self; 1309 int rv = 0, s; 1310 1311 s = splnet(); 1312 switch (act) { 1313 case DVACT_ACTIVATE: 1314 rv = EOPNOTSUPP; 1315 break; 1316 1317 case DVACT_DEACTIVATE: 1318 if_deactivate(&sc->sc_ec.ec_if); 1319 break; 1320 } 1321 splx(s); 1322 return (rv); 1323 } 1324 1325 int 1326 dp8390_detach(sc, flags) 1327 struct dp8390_softc *sc; 1328 int flags; 1329 { 1330 struct ifnet *ifp = &sc->sc_ec.ec_if; 1331 1332 /* Succeed now if there's no work to do. */ 1333 if ((sc->sc_flags & DP8390_ATTACHED) == 0) 1334 return (0); 1335 1336 /* dp8390_disable() checks sc->sc_enabled */ 1337 dp8390_disable(sc); 1338 1339 if (sc->sc_media_fini != NULL) 1340 (*sc->sc_media_fini)(sc); 1341 1342 /* Delete all remaining media. */ 1343 ifmedia_delete_instance(&sc->sc_media, IFM_INST_ANY); 1344 1345 #if NRND > 0 1346 rnd_detach_source(&sc->rnd_source); 1347 #endif 1348 ether_ifdetach(ifp); 1349 if_detach(ifp); 1350 1351 return (0); 1352 } 1353 1354 #ifdef IPKDB_DP8390 1355 static void dp8390_ipkdb_hwinit __P((struct ipkdb_if *)); 1356 static void dp8390_ipkdb_init __P((struct ipkdb_if *)); 1357 static void dp8390_ipkdb_leave __P((struct ipkdb_if *)); 1358 static int dp8390_ipkdb_rcv __P((struct ipkdb_if *, u_char *, int)); 1359 static void dp8390_ipkdb_send __P((struct ipkdb_if *, u_char *, int)); 1360 1361 /* 1362 * This is essentially similar to dp8390_config above. 1363 */ 1364 int 1365 dp8390_ipkdb_attach(kip) 1366 struct ipkdb_if *kip; 1367 { 1368 struct dp8390_softc *sc = kip->port; 1369 1370 if (sc->mem_size < 8192 * 2) 1371 sc->txb_cnt = 1; 1372 else if (sc->mem_size < 8192 * 3) 1373 sc->txb_cnt = 2; 1374 else 1375 sc->txb_cnt = 3; 1376 1377 sc->tx_page_start = sc->mem_start >> ED_PAGE_SHIFT; 1378 sc->rec_page_start = sc->tx_page_start + sc->txb_cnt * ED_TXBUF_SIZE; 1379 sc->rec_page_stop = sc->tx_page_start + (sc->mem_size >> ED_PAGE_SHIFT); 1380 sc->mem_ring = sc->mem_start + (sc->rec_page_start << ED_PAGE_SHIFT); 1381 sc->mem_end = sc->mem_start + sc->mem_size; 1382 1383 dp8390_stop(sc); 1384 1385 kip->start = dp8390_ipkdb_init; 1386 kip->leave = dp8390_ipkdb_leave; 1387 kip->receive = dp8390_ipkdb_rcv; 1388 kip->send = dp8390_ipkdb_send; 1389 1390 return 0; 1391 } 1392 1393 /* 1394 * Similar to dp8390_init above. 1395 */ 1396 static void 1397 dp8390_ipkdb_hwinit(kip) 1398 struct ipkdb_if *kip; 1399 { 1400 struct dp8390_softc *sc = kip->port; 1401 struct ifnet *ifp = &sc->sc_ec.ec_if; 1402 bus_space_tag_t regt = sc->sc_regt; 1403 bus_space_handle_t regh = sc->sc_regh; 1404 int i; 1405 1406 sc->txb_inuse = 0; 1407 sc->txb_new = 0; 1408 sc->txb_next_tx = 0; 1409 dp8390_stop(sc); 1410 1411 if (sc->dcr_reg & ED_DCR_LS) 1412 NIC_PUT(regt, regh, ED_P0_DCR, sc->dcr_reg); 1413 else 1414 NIC_PUT(regt, regh, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_LS); 1415 NIC_PUT(regt, regh, ED_P0_RBCR0, 0); 1416 NIC_PUT(regt, regh, ED_P0_RBCR1, 0); 1417 NIC_PUT(regt, regh, ED_P0_RCR, ED_RCR_MON | sc->rcr_proto); 1418 NIC_PUT(regt, regh, ED_P0_TCR, ED_TCR_LB0); 1419 if (sc->is790) 1420 NIC_PUT(regt, regh, 0x09, 0); 1421 NIC_PUT(regt, regh, ED_P0_BNRY, sc->rec_page_start); 1422 NIC_PUT(regt, regh, ED_P0_PSTART, sc->rec_page_start); 1423 NIC_PUT(regt, regh, ED_P0_PSTOP, sc->rec_page_stop); 1424 NIC_PUT(regt, regh, ED_P0_IMR, 0); 1425 NIC_BARRIER(regt, regh); 1426 NIC_PUT(regt, regh, ED_P0_ISR, 0xff); 1427 1428 NIC_BARRIER(regt, regh); 1429 NIC_PUT(regt, regh, ED_P0_CR, 1430 sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STP); 1431 NIC_BARRIER(regt, regh); 1432 1433 for (i = 0; i < sizeof kip->myenetaddr; i++) 1434 NIC_PUT(regt, regh, ED_P1_PAR0 + i, kip->myenetaddr[i]); 1435 /* multicast filter? */ 1436 1437 sc->next_packet = sc->rec_page_start + 1; 1438 NIC_PUT(regt, regh, ED_P1_CURR, sc->next_packet); 1439 1440 NIC_BARRIER(regt, regh); 1441 NIC_PUT(regt, regh, ED_P1_CR, 1442 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); 1443 NIC_BARRIER(regt, regh); 1444 1445 /* promiscuous mode? */ 1446 NIC_PUT(regt, regh, ED_P0_RCR, ED_RCR_AB | ED_RCR_AM | sc->rcr_proto); 1447 NIC_PUT(regt, regh, ED_P0_TCR, 0); 1448 1449 /* card-specific initialization? */ 1450 1451 NIC_BARRIER(regt, regh); 1452 NIC_PUT(regt, regh, ED_P0_CR, 1453 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 1454 1455 ifp->if_flags &= ~IFF_OACTIVE; 1456 } 1457 1458 static void 1459 dp8390_ipkdb_init(kip) 1460 struct ipkdb_if *kip; 1461 { 1462 struct dp8390_softc *sc = kip->port; 1463 bus_space_tag_t regt = sc->sc_regt; 1464 bus_space_handle_t regh = sc->sc_regh; 1465 u_char cmd; 1466 1467 cmd = NIC_GET(regt, regh, ED_P0_CR) & ~(ED_CR_PAGE_3 | ED_CR_STA); 1468 1469 /* Select page 0 */ 1470 NIC_BARRIER(regt, regh); 1471 NIC_PUT(regt, regh, ED_P0_CR, cmd | ED_CR_PAGE_0 | ED_CR_STP); 1472 NIC_BARRIER(regt, regh); 1473 1474 /* If not started, init chip */ 1475 if (cmd & ED_CR_STP) 1476 dp8390_ipkdb_hwinit(kip); 1477 1478 /* If output active, wait for packets to drain */ 1479 while (sc->txb_inuse) { 1480 while (!(cmd = (NIC_GET(regt, regh, ED_P0_ISR) 1481 & (ED_ISR_PTX | ED_ISR_TXE)))) 1482 DELAY(1); 1483 NIC_PUT(regt, regh, ED_P0_ISR, cmd); 1484 if (--sc->txb_inuse) 1485 dp8390_xmit(sc); 1486 } 1487 } 1488 1489 static void 1490 dp8390_ipkdb_leave(kip) 1491 struct ipkdb_if *kip; 1492 { 1493 struct dp8390_softc *sc = kip->port; 1494 struct ifnet *ifp = &sc->sc_ec.ec_if; 1495 1496 ifp->if_timer = 0; 1497 } 1498 1499 /* 1500 * Similar to dp8390_intr above. 1501 */ 1502 static int 1503 dp8390_ipkdb_rcv(kip, buf, poll) 1504 struct ipkdb_if *kip; 1505 u_char *buf; 1506 int poll; 1507 { 1508 struct dp8390_softc *sc = kip->port; 1509 bus_space_tag_t regt = sc->sc_regt; 1510 bus_space_handle_t regh = sc->sc_regh; 1511 u_char bnry, current, isr; 1512 int len, nlen, packet_ptr; 1513 struct dp8390_ring packet_hdr; 1514 1515 /* Switch to page 0. */ 1516 NIC_BARRIER(regt, regh); 1517 NIC_PUT(regt, regh, ED_P0_CR, 1518 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 1519 NIC_BARRIER(regt, regh); 1520 1521 while (1) { 1522 isr = NIC_GET(regt, regh, ED_P0_ISR); 1523 NIC_PUT(regt, regh, ED_P0_ISR, isr); 1524 1525 if (isr & (ED_ISR_PRX | ED_ISR_TXE)) { 1526 NIC_GET(regt, regh, ED_P0_NCR); 1527 NIC_GET(regt, regh, ED_P0_TSR); 1528 } 1529 1530 if (isr & ED_ISR_OVW) { 1531 dp8390_ipkdb_hwinit(kip); 1532 continue; 1533 } 1534 1535 if (isr & ED_ISR_CNT) { 1536 NIC_GET(regt, regh, ED_P0_CNTR0); 1537 NIC_GET(regt, regh, ED_P0_CNTR1); 1538 NIC_GET(regt, regh, ED_P0_CNTR2); 1539 } 1540 1541 /* Similar to dp8390_rint above. */ 1542 NIC_BARRIER(regt, regh); 1543 NIC_PUT(regt, regh, ED_P0_CR, 1544 sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STA); 1545 NIC_BARRIER(regt, regh); 1546 1547 current = NIC_GET(regt, regh, ED_P1_CURR); 1548 1549 NIC_BARRIER(regt, regh); 1550 NIC_PUT(regt, regh, ED_P1_CR, 1551 sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); 1552 NIC_BARRIER(regt, regh); 1553 1554 if (sc->next_packet == current) { 1555 if (poll) 1556 return 0; 1557 continue; 1558 } 1559 1560 packet_ptr = sc->mem_ring 1561 + ((sc->next_packet - sc->rec_page_start) << ED_PAGE_SHIFT); 1562 sc->read_hdr(sc, packet_ptr, &packet_hdr); 1563 len = packet_hdr.count; 1564 nlen = packet_hdr.next_packet - sc->next_packet; 1565 if (nlen < 0) 1566 nlen += sc->rec_page_stop - sc->rec_page_start; 1567 nlen--; 1568 if ((len & ED_PAGE_MASK) + sizeof(packet_hdr) > ED_PAGE_SIZE) 1569 nlen--; 1570 len = (len & ED_PAGE_MASK) | (nlen << ED_PAGE_SHIFT); 1571 len -= sizeof(packet_hdr); 1572 1573 if (len <= ETHERMTU 1574 && packet_hdr.next_packet >= sc->rec_page_start 1575 && packet_hdr.next_packet < sc->rec_page_stop) { 1576 sc->ring_copy(sc, packet_ptr + sizeof(packet_hdr), 1577 buf, len); 1578 sc->next_packet = packet_hdr.next_packet; 1579 bnry = sc->next_packet - 1; 1580 if (bnry < sc->rec_page_start) 1581 bnry = sc->rec_page_stop - 1; 1582 NIC_PUT(regt, regh, ED_P0_BNRY, bnry); 1583 return len; 1584 } 1585 1586 dp8390_ipkdb_hwinit(kip); 1587 } 1588 } 1589 1590 static void 1591 dp8390_ipkdb_send(kip, buf, l) 1592 struct ipkdb_if *kip; 1593 u_char *buf; 1594 int l; 1595 { 1596 struct dp8390_softc *sc = kip->port; 1597 bus_space_tag_t regt = sc->sc_regt; 1598 bus_space_handle_t regh = sc->sc_regh; 1599 struct mbuf mb; 1600 1601 mb.m_next = NULL; 1602 mb.m_pkthdr.len = mb.m_len = l; 1603 mtod(&mb, u_char *) = buf; 1604 mb.m_flags = M_EXT | M_PKTHDR; 1605 mb.m_type = MT_DATA; 1606 1607 l = sc->write_mbuf(sc, &mb, 1608 sc->mem_start + ((sc->txb_new * ED_TXBUF_SIZE) << ED_PAGE_SHIFT)); 1609 sc->txb_len[sc->txb_new] = max(l, ETHER_MIN_LEN - ETHER_CRC_LEN); 1610 1611 if (++sc->txb_new == sc->txb_cnt) 1612 sc->txb_new = 0; 1613 1614 sc->txb_inuse++; 1615 dp8390_xmit(sc); 1616 1617 while (!(NIC_GET(regt, regh, ED_P0_ISR) & (ED_ISR_PTX | ED_ISR_TXE))) 1618 DELAY(1); 1619 1620 sc->txb_inuse--; 1621 } 1622 #endif 1623