1# $NetBSD: TADPOLE3GX,v 1.60 2013/06/30 21:38:58 rmind Exp $ 2 3include "arch/sparc/conf/std.sparc" 4 5#options INCLUDE_CONFIG_FILE # embed config file in kernel binary 6 7# all supported SPARCbooks have V8 CPUs 8makeoptions CCPUOPTS="-mcpu=v8 -mtune=v8" 9 10maxusers 32 11 12## System kernel configuration. See options(4) for more detail. 13 14 15# Options for variants of the Sun SPARC architecure. 16# We currently support three architecture types; at least one is required. 17options SUN4M # sun4m - SS10, SS20, Classic, etc. 18 19## System options specific to the sparc machine type 20 21# Blink the power LED on some machines to indicate the system load. 22#options BLINK 23 24# wsdisplay options 25#options WSEMUL_SUN 26options WSEMUL_VT100 27options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes 28options WSDISPLAY_CUSTOM_OUTPUT # wsconsctl(8) 29 30# black on white, kernel output in green 31options WS_DEFAULT_FG=WSCOL_BLACK 32options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 33options WS_KERNEL_FG=WSCOL_GREEN 34options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 35 36options WSDISPLAY_COMPAT_PCVT # emulate some ioctls 37options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls 38options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 39 40options WSDISPLAY_DEFAULTSCREENS=1 41 42options SPARCBOOK_CMD # enable screen switching with lAlt-Fn 43#options FONT_GALLANT12x22 # the console font 44options FONT_BOLD8x16 # a somewhat smaller font 45 46#### System options that are the same for all ports 47 48## Root device configuration: change the ?'s if you are going to use a 49## nonstandard root partition (other than where the kernel is booted from) 50## and/or nonstandard root type (not ffs or nfs). Normally this can be 51## automagically determined at boot time. 52 53config netbsd root on ? type ? 54 55## System call tracing (see ktrace(1)). 56options KTRACE 57 58## Collect statistics on kernel malloc's and free's. This does have a 59## significant performance hit on slower machines, so it is intended for 60## diagnostic use only. 61#options KMEMSTATS 62 63## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 64options SYSVMSG # System V message queues 65options SYSVSEM # System V semaphores 66options SYSVSHM # System V shared memory 67 68options USERCONF # userconf(4) support 69#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 70#options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 71 72## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 73options NFS_BOOT_BOOTPARAM 74#options NFS_BOOT_BOOTP 75options NFS_BOOT_DHCP 76 77#### Debugging options 78 79## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 80## serial console break or keyboard reset, where the PROM would normally 81## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 82options DDB # kernel dynamic debugger 83options DDB_HISTORY_SIZE=100 # enable history editing in DDB 84#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 85 86## You may also use gdb, on another computer connected to this machine over 87## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 88## KGDB_DEV is a dev_t encoded device number of the serial port to use. 89## (0xc01 = ttya, 0xc02 = ttyb.) 90#options KGDB # support for kernel gdb 91#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 92#options KGDB_DEVRATE=38400 # baud rate 93 94 95## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 96## such that gdb(1) can be used on a kernel coredump. 97 98makeoptions DEBUG="-g" 99 100 101## Adds code to the kernel that does internal consistency checks, and will 102## cause the kernel to panic if corruption of internal data structures 103## is detected. 104#options DIAGNOSTIC # extra kernel sanity checking 105 106## Enable (possibly expensive) debugging code that may also display messages 107## on the system console 108#options DEBUG 109#options LOCKDEBUG 110#options SYSCALL_DEBUG 111 112## Make SCSI error messages more verbose when explaining their meanings. 113options SCSIVERBOSE 114 115## `INSECURE' turns off the kernel security level (securelevel = 0 always). 116## This allows writing to /dev/mem, loading kernel modules while multi-user, 117## and other insecurities good only for development work. Do not use this 118## option on a production machine. 119options INSECURE 120 121## `FDSCRIPTS' allows non-readable but executable scripts by providing a 122## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 123## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 124## opaque file mechanism. Perl calls this "secure setuid scripts." 125 126#options FDSCRIPTS 127#options SETUIDSCRIPTS 128 129## Options for compatibility with previous releases foreign system binaries. 130## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 131## additional user-level utilities or system configuration files. See 132## compat_sunos(8) and compat_svr4(8). 133 134options COMPAT_43 # 4.3BSD system interfaces 135options COMPAT_10 # NetBSD 1.0 binary compatibility 136options COMPAT_11 # NetBSD 1.1 binary compatibility 137options COMPAT_12 # NetBSD 1.2 binary compatibility 138options COMPAT_13 # NetBSD 1.3 binary compatibility 139options COMPAT_14 # NetBSD 1.4 binary compatibility 140options COMPAT_15 # NetBSD 1.5 binary compatibility 141options COMPAT_16 # NetBSD 1.6 binary compatibility 142options COMPAT_20 # NetBSD 2.0 binary compatibility 143options COMPAT_30 # NetBSD 3.0 binary compatibility 144options COMPAT_40 # NetBSD 4.0 binary compatibility 145options COMPAT_50 # NetBSD 5.0 binary compatibility 146options COMPAT_60 # NetBSD 6.0 compatibility. 147options COMPAT_SUNOS # SunOS 4.x binary compatibility 148options COMPAT_SVR4 # SunOS 5.x binary compatibility 149#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 150options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 151 152## File systems. You probably need at least one of FFS or NFS. 153file-system FFS # Berkeley Fast Filesystem 154file-system NFS # Sun NFS-compatible filesystem client 155file-system KERNFS # kernel data-structure filesystem 156#file-system NULLFS # NULL layered filesystem 157file-system MFS # memory-based filesystem 158#file-system FDESC # user file descriptor filesystem 159#file-system UMAPFS # uid/gid remapping filesystem 160#file-system LFS # Log-based filesystem (still experimental) 161file-system PROCFS # /proc 162file-system CD9660 # ISO 9660 + Rock Ridge file system 163#file-system UNION # union file system 164file-system MSDOSFS # MS-DOS FAT filesystem(s). 165file-system PTYFS # /dev/pts/N support 166 167## File system options. 168options NFSSERVER # Sun NFS-compatible filesystem server 169options QUOTA # legacy UFS quotas 170options QUOTA2 # new, in-filesystem UFS quotas 171#options FFS_EI # FFS Endian Independent support 172#options FFS_NO_SNAPSHOT # No FFS snapshot support 173 174## Network protocol support. In most environments, INET is required. 175options INET # IP (Internet Protocol) v4 176#options GATEWAY # packet forwarding ("router switch") 177#options MROUTING # packet forwarding of multicast packets 178#options PIM # Protocol Independent Multicast 179#options DIRECTED_BROADCAST # allow broadcasts through routers 180#options NETATALK # AppleTalk (over Ethernet) protocol 181options NTP # Network Time Protocol in-kernel support 182#options PPS_SYNC # Add serial line synchronization for NTP 183options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 184options IPFILTER_LOOKUP # ippool(8) support 185options IPFILTER_COMPAT # Compat for IP-Filter 186#options IPFILTER_DEFAULT_BLOCK # block all packets by default 187options PPP_BSDCOMP # Add BSD compression to ppp device 188options PPP_DEFLATE # Add deflate (libz) compression to ppp device 189options PPP_FILTER # Add active filters for ppp (via bpf) 190#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 191 192 193#### Main bus and CPU .. all systems. 194mainbus0 at root 195cpu0 at mainbus0 196 197#### Bus types found on SPARC systems. 198 199obio0 at mainbus0 # sun4 and sun4m 200iommu0 at mainbus0 # sun4m 201sbus0 at iommu0 # sun4m 202 203## SBus to PCMCIA bridge 204tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 205pcmcia* at tslot? 206 207#### Standard system devices -- all required for a given architecture 208 209## Auxiliary system registers on sun4c and sun4m 210auxreg0 at obio0 # sun4m 211 212## Additional auxiliary system registers on Sparcbook 213auxiotwo0 at obio0 # sun4m 214 215## Clock control on SPARCbook - used to put the CPU to sleep when idle 216clkctrl0 at obio0 217 218## Mostek clock found on 4/300, sun4c, and sun4m systems. 219## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 220clock0 at obio0 # sun4m 221 222## Timer chip found on 4/300, sun4c, and sun4m systems. 223timer0 at obio0 # sun4m 224 225#### Serial port configuration 226 227## Zilog 8530 serial chips. Each has two-channels. 228## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 229zs0 at obio0 # sun4m 230zstty0 at zs0 channel 0 # ttya 231zstty1 at zs0 channel 1 # ttyb 232 233zs1 at obio0 # sun4m 234zstty* at zs1 channel ? # mouse/keyboard 235 236kbd0 at zstty? 237ms0 at zstty? 238 239wskbd* at kbd? console ? 240wsmouse* at ms? 241 242## Tadpole 3GX/3XL have a builtin modem that emulates a NS16450. 243com* at obio0 # sun4m (tadpole) 244 245## PCMCIA serial interfaces 246com* at pcmcia? 247pcmcom* at pcmcia? 248com* at pcmcom? 249 250#### Disk controllers and disks 251 252# 253 254## The following flags may be set for the NCR53c94 based esp driver: 255## bits 0-7: disable disconnect/reselect for the corresponding target 256## bits 8-15: disable synchronous negotiation for target [bit-8] 257 258## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 259## Both `dma' and `esp' are needed in all cases. 260## Two kinds of additional SBus SCSI interfaces are available. One uses 261## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 262 263## sun4/300 SCSI - an NCR53c94 or equivalent behind 264## an LSI Logic DMA controller 265 266dma0 at sbus0 slot ? offset ? # sun4c/sun4m 267esp0 at dma0 flags 0x0000 # sun4m 268 269scsibus* at esp? 270 271## PCMCIA SCSI controllers 272#aic* at pcmcia? 273#scsibus* at aic? 274 275## These entries find devices on all SCSI busses and assign 276## unit numbers dynamically. 277sd* at scsibus? target ? lun ? # SCSI disks 278st* at scsibus? target ? lun ? # SCSI tapes 279cd* at scsibus? target ? lun ? # SCSI CD-ROMs 280ch* at scsibus? target ? lun ? # SCSI changer devices 281ss* at scsibus? target ? lun ? # SCSI scanners 282uk* at scsibus? target ? lun ? # unknown SCSI 283 284## PCMCIA IDE controllers 285wdc* at pcmcia? 286 287atabus* at ata? 288wd* at atabus? drive ? flags 0x0000 289 290## A disk-like interface to files. Can be used to create floppy, CD, 291## miniroot images, etc. 292 293pseudo-device vnd 294 295## Memory disk device, used on boot floppies with compressed 296## kernel-plus-root-disk images. 297 298#pseudo-device md 299 300 301#### Network interfaces 302 303## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 304## Three flavors of additional SBus ethernets are available. One attaches 305## directly like the sun4c on-board, one uses the ledma device like the 306## sun4m on-board, and one uses the lebuffer device. 307 308ledma0 at sbus0 slot ? offset ? # sun4m on-board 309le0 at ledma0 # sun4m on-board 310 311# PCMCIA ethernet devices 312ep* at pcmcia? 313#mbe* at pcmcia? 314#ne* at pcmcia? 315#sm* at pcmcia? 316 317wi* at pcmcia? 318 319## Loopback network interface; required 320pseudo-device loop 321 322## PPP, the successor to SLIP. See pppd(8). 323pseudo-device ppp 324 325## Network "tunnel" device, allowing protocol stacks to run in the userland. 326## This is used by the third-party user-mode "ppp" program, and others. 327pseudo-device tun 328 329## Generic L3 over IP tunnel 330#pseudo-device gre # generic L3 over IP tunnel 331 332## Berkeley Packet Filter, required to run RARPD. A generic C-language 333## interface that allows selective examining of incoming packets. 334pseudo-device bpfilter 335 336## IP Filter, used in firewall and NAT applications. See ipnat(8) for 337## one example of the use of the IP Filter. 338pseudo-device ipfilter 339 340 341#### Audio and video devices 342 343## /dev/audio support 344 345#options DBRI_DEBUG # noisy debug output from the dbri driver 346options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 347dbri0 at sbus0 slot ? offset ? # SUNW,DBRI[s3|e] 348audio* at audiobus? 349 350# Tadpole 3GX/3GS (P9100 -- P Nine One Zero Zero -> pnozz) 351pnozz0 at sbus? slot ? offset ? 352#options PNOZZ_EMUL_CG3 # emulate a CG3 for Xsun instead of 353 # running natively 354 355wsdisplay* at wsemuldisplaydev? console ? 356 357#### Other device configuration 358 359# Tadpole microcontroller 360tctrl0 at obio0 361 362## Pseudo ttys, required for network logins and programs like screen. 363 364pseudo-device pty # pseudo-ttys (for network, etc.) 365 366## Random device, used to implement /dev/random (a source of random noise), 367## and generate randomness for some kernel formulae. 368 369 370pseudo-device clockctl # user control of clock subsystem 371#pseudo-device fss # file system snapshot device 372 373pseudo-device wsmux # mouse and keyboard multiplexor 374pseudo-device wsfont 375