1# $NetBSD: GENERIC,v 1.249 2015/09/26 11:16:13 maxv Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.249 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54#options WSEMUL_SUN 55options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 85options SYSVMSG # System V message queues 86options SYSVSEM # System V semaphores 87options SYSVSHM # System V shared memory 88 89options MODULAR # new style module(7) framework 90options MODULAR_DEFAULT_AUTOLOAD 91 92options USERCONF # userconf(4) support 93#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 94options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 95 96# Enable experimental buffer queue strategy for better responsiveness under 97# high disk I/O load. Use it with caution - it's not proven to be stable yet. 98#options BUFQ_READPRIO 99#options BUFQ_PRIOCSCAN 100 101## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 102options NFS_BOOT_BOOTPARAM 103#options NFS_BOOT_BOOTP 104options NFS_BOOT_DHCP 105 106#### Debugging options 107 108## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 109## serial console break or keyboard reset, where the PROM would normally 110## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 111options DDB # kernel dynamic debugger 112options DDB_HISTORY_SIZE=100 # enable history editing in DDB 113#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 114 115## You may also use gdb, on another computer connected to this machine over 116## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 117## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 118## the minor device number encodes the PROM enumeration of the serial ports, 119## i.e.: 120## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 121## (Note: ttyc and ttyd are available only on some sun4 models) 122#options KGDB # support for kernel gdb 123#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 124#options KGDB_DEVRATE=38400 # baud rate 125 126 127## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 128## such that gdb(1) can be used on a kernel coredump. 129 130#makeoptions DEBUG="-g" 131 132 133## Adds code to the kernel that does internal consistency checks, and will 134## cause the kernel to panic if corruption of internal data structures 135## is detected. 136#options DIAGNOSTIC # extra kernel sanity checking 137 138## Enable (possibly expensive) debugging code that may also display messages 139## on the system console 140#options DEBUG 141#options LOCKDEBUG 142#options SYSCALL_DEBUG 143 144## Make SCSI error messages more verbose when explaining their meanings. 145options SCSIVERBOSE 146 147options MIIVERBOSE # verbose PHY autoconfig messages 148 149## `INSECURE' turns off the kernel security level (securelevel = 0 always). 150## This allows writing to /dev/mem, loading kernel modules while multi-user, 151## and other insecurities good only for development work. Do not use this 152## option on a production machine. 153#options INSECURE 154 155## `FDSCRIPTS' allows non-readable but executable scripts by providing a 156## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 157## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 158## opaque file mechanism. Perl calls this "secure setuid scripts." 159 160#options FDSCRIPTS 161#options SETUIDSCRIPTS 162 163## Options for compatibility with previous releases foreign system binaries. 164## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 165## additional user-level utilities or system configuration files. See 166## compat_sunos(8) and compat_svr4(8). 167 168options COMPAT_43 # 4.3BSD system interfaces 169options COMPAT_10 # NetBSD 1.0, 170options COMPAT_11 # NetBSD 1.1, 171options COMPAT_12 # NetBSD 1.2, 172options COMPAT_13 # NetBSD 1.3, 173options COMPAT_14 # NetBSD 1.4, 174options COMPAT_15 # NetBSD 1.5, 175options COMPAT_16 # NetBSD 1.6, 176options COMPAT_20 # NetBSD 2.0, 177options COMPAT_30 # NetBSD 3.0, 178options COMPAT_40 # NetBSD 4.0, 179options COMPAT_50 # NetBSD 5.0, 180options COMPAT_60 # NetBSD 6.0, and 181options COMPAT_70 # NetBSD 7.0 binary compatibility 182options COMPAT_SUNOS # SunOS 4.x binary compatibility 183options COMPAT_SVR4 # SunOS 5.x binary compatibility 184options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 185 186## File systems. You probably need at least one of FFS or NFS. 187file-system FFS # Berkeley Fast Filesystem 188file-system NFS # Sun NFS-compatible filesystem client 189file-system KERNFS # kernel data-structure filesystem 190file-system NULLFS # NULL layered filesystem 191file-system OVERLAY # overlay file system 192file-system MFS # memory-based filesystem 193file-system FDESC # user file descriptor filesystem 194file-system UMAPFS # uid/gid remapping filesystem 195file-system LFS # Log-based filesystem (still experimental) 196file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 197file-system PROCFS # /proc 198file-system CD9660 # ISO 9660 + Rock Ridge file system 199file-system UNION # union file system 200file-system MSDOSFS # MS-DOS FAT filesystem(s). 201file-system CODA # Coda File System; also needs vcoda (below) 202file-system PTYFS # /dev/pts/N support 203file-system TMPFS # Efficient memory file-system 204#file-system UDF # experimental - OSTA UDF CD/DVD file-system 205 206## File system options. 207options NFSSERVER # Sun NFS-compatible filesystem server 208options QUOTA # FFS quotas 209#options FFS_EI # FFS Endian Independent support 210options WAPBL # File system journaling support 211#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 212#options FFS_NO_SNAPSHOT # No FFS snapshot support 213options UFS_EXTATTR # Extended attribute support for UFS1 214 215## Network protocol support. In most environments, INET is required. 216options INET # IP (Internet Protocol) v4 217options INET6 # IPV6 218#options IPSEC # IP security 219#options IPSEC_DEBUG # debug for IP security 220#options GATEWAY # packet forwarding ("router switch") 221#options MROUTING # packet forwarding of multicast packets 222#options PIM # Protocol Independent Multicast 223#options DIRECTED_BROADCAST # allow broadcasts through routers 224#options NETATALK # AppleTalk (over Ethernet) protocol 225options NTP # Network Time Protocol in-kernel support 226#options PPS_SYNC # Add serial line synchronization for NTP 227options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 228options IPFILTER_LOOKUP # ippool(8) support 229options IPFILTER_COMPAT # Compat for IP-Filter 230#options IPFILTER_DEFAULT_BLOCK # block all packets by default 231options PPP_BSDCOMP # Add BSD compression to ppp device 232options PPP_DEFLATE # Add deflate (libz) compression to ppp device 233options PPP_FILTER # Add active filters for ppp (via bpf) 234 235#options ALTQ # Manipulate network interfaces' output queues 236#options ALTQ_BLUE # Stochastic Fair Blue 237#options ALTQ_CBQ # Class-Based Queueing 238#options ALTQ_CDNR # Diffserv Traffic Conditioner 239#options ALTQ_FIFOQ # First-In First-Out Queue 240#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 241#options ALTQ_HFSC # Hierarchical Fair Service Curve 242#options ALTQ_LOCALQ # Local queueing discipline 243#options ALTQ_PRIQ # Priority Queueing 244#options ALTQ_RED # Random Early Detection 245#options ALTQ_RIO # RED with IN/OUT 246#options ALTQ_WFQ # Weighted Fair Queueing 247 248 249 250#### Main bus and CPU .. all systems. 251mainbus0 at root 252cpu0 at mainbus0 253cpuunit0 at mainbus0 # sun4d 254cpuunit* at mainbus0 # sun4d 255cpu0 at cpuunit0 # sun4d 256 257#### SX rendering engine found in SS20 and SS10SX 258sx0 at mainbus0 259 260#### Bus types found on SPARC systems. 261 262sbus0 at mainbus0 # sun4c 263obio0 at mainbus0 # sun4 and sun4m 264sparcvme0 at mainbus0 # sun4 265iommu0 at mainbus0 # sun4m 266sbus0 at iommu0 # sun4m 267sparcvme0 at iommu0 # sun4m 268vme0 at sparcvme0 # MI VME attachment 269bootbus0 at cpuunit0 # sun4d 270bootbus* at cpuunit? # sun4d 271 272## SBus expander box 273xbox* at sbus? slot ? offset ? 274sbus* at xbox? 275 276## SBus to PCMCIA bridge 277nell* at sbus? slot ? offset ? # PCMCIA bridge 278pcmcia* at nell? 279tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 280pcmcia* at tslot? 281 282#### Standard system devices -- all required for a given architecture 283 284## Auxiliary system registers on sun4c and sun4m 285auxreg0 at mainbus0 # sun4c 286auxreg0 at obio0 # sun4m 287auxiotwo0 at obio0 # only on Tadpole SPARCbook. 288 289## Power status and control register on Sun4m systems 290power0 at obio0 291 292## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 293## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 294clock0 at mainbus0 # sun4c 295clock0 at obio0 # sun4m 296clock0 at obio0 addr 0xf2000000 # sun4/300 297clock0 at bootbus0 # sun4d 298 299## Intersil clock found on 4/100 and 4/200 systems. 300oclock0 at obio0 addr 0xf3000000 # sun4/200 301oclock0 at obio0 addr 0x03000000 # sun4/100 302 303## Memory error registers. 304memreg0 at mainbus0 # sun4c 305memreg0 at obio0 # sun4m 306memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 307memreg0 at obio0 addr 0x04000000 # sun4/100 308 309## ECC memory control 310eccmemctl0 at mainbus0 # sun4m 311 312## Timer chip found on 4/300, sun4c, and sun4m systems. 313timer0 at mainbus0 # sun4c 314timer0 at obio0 # sun4m 315timer0 at obio0 addr 0xef000000 # sun4/300 316 317## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 318## doesn't use this driver; the `EEPROM' is in the NVRAM on the 319## Mostek clock chip on 4/300 systems. 320eeprom0 at obio0 addr 0xf2000000 # sun4/200 321eeprom0 at obio0 addr 0x02000000 # sun4/100 322 323 324#### Serial port configuration 325 326## Zilog 8530 serial chips. Each has two-channels. 327## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 328zs0 at mainbus0 # sun4c 329zs0 at obio0 # sun4m 330zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 331zs0 at obio0 addr 0x01000000 level 12 # sun4/100 332zs0 at bootbus0 # sun4d 333zstty0 at zs0 channel 0 # ttya 334zstty1 at zs0 channel 1 # ttyb 335 336zs1 at mainbus0 # sun4c 337zs1 at obio0 # sun4m 338zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 339zs1 at obio0 addr 0x00000000 level 12 # sun4/100 340zs1 at bootbus0 # sun4d 341 342# old kbd and mouse attachments 343#kbd0 at zs1 channel 0 # keyboard 344#ms0 at zs1 channel 1 # mouse 345zstty* at zs? 346 347# these are for wscons 348kbd0 at zstty? 349ms0 at zstty? 350wskbd* at wskbddev? 351wsmouse* at wsmousedev? 352 353zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 354zstty2 at zs2 channel 0 # ttyc 355zstty3 at zs2 channel 1 # ttyd 356 357zs* at bootbus? # sun4d 358zstty* at zs? 359 360## NS16x50 serial chips and clones. Present on the 361## Sun JavaStation-1 and Tadpole SPARCbook 3 362com* at obio0 # sun4m 363 364# Parallel port. 365bpp* at sbus? slot? offset ? 366 367## Magma Serial/Parallel driver 368magma* at sbus? slot ? offset ? 369mtty* at magma? 370mbpp* at magma? 371 372## SUNW,spif Serial/Parallel driver 373spif* at sbus? slot ? offset ? 374stty* at spif? 375sbpp* at spif? 376 377## PCMCIA serial interfaces 378#com* at pcmcia? 379#pcmcom* at pcmcia? 380#com* at pcmcom? 381 382#### Disk controllers and disks 383 384# 385 386## The following flags may be set for the NCR53c94 based esp driver: 387## bits 0-7: disable disconnect/reselect for the corresponding target 388## bits 8-15: disable synchronous negotiation for target [bit-8] 389 390## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 391## Both `dma' and `esp' are needed in all cases. 392## Two kinds of additional SBus SCSI interfaces are available. One uses 393## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 394 395## sun4/300 SCSI - an NCR53c94 or equivalent behind 396## an LSI Logic DMA controller 397 398dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 399esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 400 401dma0 at sbus0 slot ? offset ? # sun4c/sun4m 402esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 403esp0 at dma0 flags 0x0000 # sun4m 404 405# FSBE/S SCSI & SunSwift Sbus FAS366 406dma* at sbus? slot ? offset ? # SBus 407esp* at sbus? slot ? offset ? flags 0x0000 # SBus 408esp* at dma? flags 0x0000 # SBus 409 410scsibus* at esp? 411 412## Qlogic ISP SBus SCSI Card 413isp* at sbus? slot ? offset ? 414scsibus* at isp? 415 416## NCR5380-based "Sun SCSI 3" VME SCSI controller. 417## This driver has several flags which may be enabled by OR'ing 418## the values and using the "flags" directive. 419## Valid flags are: 420## 421## 0x01 Use DMA (may be polled) 422## 0x02 Use DMA completion interrupts 423## 0x04 Allow disconnect/reselect 424## 425## E.g. the following would enable DMA, interrupts, and reselect: 426## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 427## 428## By default, DMA is enabled in the driver. 429 430si0 at vme0 addr 0x200000 irq 2 vect 0x40 431scsibus* at si? 432 433## NCR5380-based "SCSI Weird" on-board SCSI interface found 434## on sun4/100 systems. The flags are the same as the "si" 435## controller. Note, while DMA is enabled by default, only 436## polled DMA works at this time, and reselects do not work 437## on this particular controller. 438 439sw0 at obio0 addr 0x0a000000 level 3 440scsibus* at sw? 441 442## PCMCIA SCSI controllers 443#aic* at pcmcia? 444#spc* at pcmcia? 445#scsibus* at aic? 446#scsibus* at spc? 447 448 449## These entries find devices on all SCSI busses and assign 450## unit numbers dynamically. 451sd* at scsibus? target ? lun ? # SCSI disks 452st* at scsibus? target ? lun ? # SCSI tapes 453cd* at scsibus? target ? lun ? # SCSI CD-ROMs 454ch* at scsibus? target ? lun ? # SCSI changer devices 455ss* at scsibus? target ? lun ? # SCSI scanners 456ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 457uk* at scsibus? target ? lun ? # unknown SCSI 458 459 460## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 461## on sun4 systems. 462xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 463xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 464xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 465xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 466xd* at xdc? drive ? 467 468## Xylogics 451 or 451 VME SMD disk controllers and disks, found 469## on sun4 systems. 470xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 471xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 472xy* at xyc? drive ? 473 474 475## Floppy controller and drive found on SPARCstations. 476 477fdc0 at mainbus0 # sun4c controller 478fdc0 at obio0 # sun4m controller 479fd* at fdc0 # the drive itself 480 481## PCMCIA IDE controllers 482#wdc* at pcmcia? 483#atabus* at ata? 484#wd* at atabus? drive ? flags 0x0000 485 486## A disk-like interface to files. Can be used to create floppy, CD, 487## miniroot images, etc. 488 489pseudo-device vnd 490#options VND_COMPRESSION # compressed vnd(4) 491 492## Concatenated and striped disks; with this, you can create a software-based 493## disk array similar to a "RAID 0" setup. See ccd(4). 494 495pseudo-device ccd 496 497## Cryptographic disk devices; See cgd(4) 498 499#pseudo-device cgd 500 501## RAIDframe disk driver: software RAID driver. See raid(4). 502 503pseudo-device raid 504options RAID_AUTOCONFIG # auto-configuration of RAID components 505# Options to enable various other RAIDframe RAID types. 506# options RF_INCLUDE_EVENODD=1 507# options RF_INCLUDE_RAID5_RS=1 508# options RF_INCLUDE_PARITYLOGGING=1 509# options RF_INCLUDE_CHAINDECLUSTER=1 510# options RF_INCLUDE_INTERDECLUSTER=1 511# options RF_INCLUDE_PARITY_DECLUSTERING=1 512# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 513 514 515## Memory disk device, used on boot floppies with compressed 516## kernel-plus-root-disk images. 517 518#pseudo-device md 519 520 521#### Network interfaces 522 523## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 524## Three flavors of additional SBus ethernets are available. One attaches 525## directly like the sun4c on-board, one uses the ledma device like the 526## sun4m on-board, and one uses the lebuffer device. 527 528le0 at obio0 addr 0xf9000000 level 6 # sun4/300 529le0 at sbus0 slot ? offset ? # sun4c on-board 530ledma0 at sbus0 slot ? offset ? # sun4m on-board 531le0 at ledma0 # sun4m on-board 532le* at sbus? slot ? offset ? # SBus 533ledma* at sbus? slot ? offset ? # SBus 534le* at ledma? # SBus 535lebuffer0 at sbus? slot ? offset ? # SBus 536le0 at lebuffer? # SBus 537lebuffer* at sbus? slot ? offset ? # SBus 538le* at lebuffer? # SBus 539 540 541## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 542## or on a Multibus/VME card. 543ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 544ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 545## VME: the first [addr,len] pair specifies the device registers; 546## the second pair specifies the on-board memory buffer 547ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 548ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 549ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 550ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 551 552## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 553## (qe, 10MBd) attached. 554qec* at sbus? slot ? offset ? # Quad Ethernet Controller 555be* at qec? # BigMac Ethernet (10/100MBd) 556qe* at qec? # Mace Ethernet (10MBd) 557 558## Happy Meal Ethernet 559hme* at sbus? slot ? offset ? 560 561# midway ATM 562en0 at sbus? slot ? offset ? 563 564# PCMCIA ethernet devices 565#ep* at pcmcia? 566#mbe* at pcmcia? 567#ne* at pcmcia? 568#sm* at pcmcia? 569 570## PCMCIA wavelan card 571#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 572 573# MII/PHY support 574exphy* at mii? phy ? # 3Com internal PHYs 575icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 576inphy* at mii? phy ? # Intel 82555 PHYs 577lxtphy* at mii? phy ? # Level One LXT-970 PHYs 578nsphy* at mii? phy ? # NS83840 PHYs 579qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 580sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 581tlphy* at mii? phy ? # ThunderLAN PHYs 582ukphy* at mii? phy ? # generic unknown PHYs 583 584## Loopback network interface; required 585pseudo-device loop 586 587## SLIP and CSLIP interfaces, for IP over a serial line. 588pseudo-device sl 589 590## PPP, the successor to SLIP. See pppd(8). 591pseudo-device ppp 592 593## PPP over Ethernet (RFC 2516) 594pseudo-device pppoe 595 596## Starmode Radio IP, a special hardware network device. 597#pseudo-device strip 598 599## Network "tunnel" device, allowing protocol stacks to run in the userland. 600## This is used by the third-party user-mode "ppp" program, and others. 601pseudo-device tun 602pseudo-device tap # virtual Ethernet 603 604## Generic L3 over IP tunnel 605#pseudo-device gre # generic L3 over IP tunnel 606 607## Berkeley Packet Filter, required to run RARPD. A generic C-language 608## interface that allows selective examining of incoming packets. 609pseudo-device bpfilter 610 611#pseudo-device carp # Common Address Redundancy Protocol 612 613## IP Filter, used in firewall and NAT applications. See ipnat(8) for 614## one example of the use of the IP Filter. 615pseudo-device ipfilter 616 617## for IPv6 618pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 619#pseudo-device faith # IPv[46] tcp relay translation i/f 620pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 621 622## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 623pseudo-device vlan 624 625## Simple inter-network traffic bridging 626pseudo-device bridge 627#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 628pseudo-device agr # IEEE 802.3ad link aggregation 629 630## accept filters 631pseudo-device accf_data # "dataready" accept filter 632pseudo-device accf_http # "httpready" accept filter 633 634#### Audio and video devices 635 636## /dev/audio support (`audioamd' plus `audio') 637## 638audioamd0 at mainbus0 # sun4c 639audioamd0 at obio0 # sun4m 640audioamd0 at sbus0 slot ? offset ? # sun4m 641 642audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 643 644#options DBRI_DEBUG # noisy debug output from the dbri driver 645#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 646dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 647 648audio* at audiobus? 649 650## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 651## systems. If your sun4 system has a cgfour installed in the P4 slot, 652## the P4 entries for "bwtwo" will attach to the overlay plane of the 653## "cgfour". 654 655bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 656bwtwo* at sbus? slot ? offset ? # 657bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 658bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 659bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 660 661## Sun "cgtwo" VME color framebuffer 662# XXX no wsdisplay support 663#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 664 665## Sun "cgthree" Sbus color framebuffer 666cgthree0 at sbus? slot ? offset ? 667cgthree* at sbus? slot ? offset ? 668 669## Sun "cgfour" color framebuffer with overlay plane. See above comment 670## regarding overlay plane. 671# XXX no wsdisplay support 672#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 673#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 674 675## Sun "cgsix" accelerated color framebuffer. 676cgsix0 at sbus? slot ? offset ? 677cgsix* at sbus? slot ? offset ? 678cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 679cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 680 681## Sun "cgeight" 24-bit framebuffer 682# XXX no wsdisplay support 683#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 684#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 685 686## Sun "tcx" accelerated color framebuffer. 687# there can be only one 688tcx0 at sbus? slot ? offset ? 689 690## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 691## runs monochrome only for now 692cgtwelve* at sbus? slot ? offset ? 693 694# Sun "cgfourteen" accelerated 24-bit framebuffer. 695cgfourteen* at obio0 # sun4m 696 697# P9100-based display on Tadpole SPARCbook 3. 698pnozz0 at sbus? slot ? offset ? 699# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 700# 'latched in' but at least my 3GX works happily without 701# Enable it by default since we don't know which hardware really needs it. 702options PNOZZ_USE_LATCH 703 704# Sun ZX/Leo 24-bit framebuffer 705zx* at sbus? slot ? offset ? 706 707# Fujitsu AG-10e accelerated graphics 8/24-bit board 708agten* at sbus? slot ? offset ? 709 710# generic framebuffer console 711genfb* at sbus? slot ? offset ? 712 713# make sure wsdisplay0 is the console 714wsdisplay0 at wsemuldisplaydev? console 1 715wsdisplay* at wsemuldisplaydev? 716 717#### Other device configuration 718 719# Tadpole microcontroller 720tctrl0 at obio0 721 722# Aurora Personality Chip (APC) on SPARCstation-4/5 723# Not enabled by default as it may hang some systems 724#apc* at sbus? slot ? offset ? 725 726## Pseudo ttys, required for network logins and programs like screen. 727 728pseudo-device pty # pseudo-terminals 729 730## Random device, used to implement /dev/random (a source of random noise), 731## and generate randomness for some kernel formulae. 732 733 734# a pseudo device needed for Coda # also needs CODA (above) 735pseudo-device vcoda # coda minicache <-> venus comm. 736 737pseudo-device clockctl # user control of clock subsystem 738pseudo-device ksyms # /dev/ksyms 739#pseudo-device pf # PF packet filter 740#pseudo-device pflog # PF log if 741pseudo-device fss # file system snapshot device 742pseudo-device wsmux # mouse and keyboard multiplexor 743pseudo-device wsfont 744pseudo-device putter # for puffs and pud 745 746#options FILEASSOC # fileassoc(9) 747 748# Veriexec 749# 750# a pseudo device needed for veriexec 751#pseudo-device veriexec 752# 753# Uncomment the fingerprint methods below that are desired. Note that 754# removing fingerprint methods will have almost no impact on the kernel 755# code size. 756# 757#options VERIFIED_EXEC_FP_RMD160 758#options VERIFIED_EXEC_FP_SHA256 759#options VERIFIED_EXEC_FP_SHA384 760#options VERIFIED_EXEC_FP_SHA512 761#options VERIFIED_EXEC_FP_SHA1 762#options VERIFIED_EXEC_FP_MD5 763 764#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 765 # (for static binaries only for now) 766