1# $NetBSD: GENERIC,v 1.267 2019/05/08 13:40:16 isaki Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.267 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46# wscons stuff 47#options WSEMUL_SUN 48options WSEMUL_VT100 49options WSDISPLAY_COMPAT_RAWKBD 50options WSDISPLAY_CUSTOM_OUTPUT 51options WS_DEFAULT_FG=WSCOL_BLACK 52options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 53options WS_KERNEL_FG=WSCOL_GREEN 54options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 55options WSDISPLAY_COMPAT_PCVT 56options WSDISPLAY_COMPAT_SYSCONS 57options WSDISPLAY_COMPAT_USL # wsconscfg VT handling 58 59options WSDISPLAY_SCROLLSUPPORT 60 61options FONT_GALLANT12x22 # the console font 62options FONT_BOLD8x16 # a somewhat smaller font 63 64#### System options that are the same for all ports 65 66## Root device configuration: change the ?'s if you are going to use a 67## nonstandard root partition (other than where the kernel is booted from) 68## and/or nonstandard root type (not ffs or nfs). Normally this can be 69## automagically determined at boot time. 70 71config netbsd root on ? type ? 72 73## System call tracing (see ktrace(1)). 74options KTRACE 75 76## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 77options SYSVMSG # System V message queues 78options SYSVSEM # System V semaphores 79options SYSVSHM # System V shared memory 80 81options MODULAR # new style module(7) framework 82options MODULAR_DEFAULT_AUTOLOAD 83 84options USERCONF # userconf(4) support 85#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 86options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 87 88# Alternate buffer queue strategies for better responsiveness under high 89# disk I/O load. 90#options BUFQ_READPRIO 91options BUFQ_PRIOCSCAN 92 93## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 94options NFS_BOOT_BOOTPARAM 95#options NFS_BOOT_BOOTP 96options NFS_BOOT_DHCP 97 98#### Debugging options 99 100## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 101## serial console break or keyboard reset, where the PROM would normally 102## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 103options DDB # kernel dynamic debugger 104options DDB_HISTORY_SIZE=100 # enable history editing in DDB 105#options DDB_ONPANIC=1 # see also sysctl(7): `ddb.onpanic' 106 107## You may also use gdb, on another computer connected to this machine over 108## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 109## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 110## the minor device number encodes the PROM enumeration of the serial ports, 111## i.e.: 112## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 113## (Note: ttyc and ttyd are available only on some sun4 models) 114#options KGDB # support for kernel gdb 115#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 116#options KGDB_DEVRATE=38400 # baud rate 117 118 119## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 120## such that gdb(1) can be used on a kernel coredump. 121 122#makeoptions DEBUG="-g" 123 124 125## Adds code to the kernel that does internal consistency checks, and will 126## cause the kernel to panic if corruption of internal data structures 127## is detected. 128options DIAGNOSTIC # extra kernel sanity checking 129 130## Enable (possibly expensive) debugging code that may also display messages 131## on the system console 132#options DEBUG 133#options LOCKDEBUG 134#options SYSCALL_DEBUG 135 136## Make SCSI error messages more verbose when explaining their meanings. 137options SCSIVERBOSE 138 139options MIIVERBOSE # verbose PHY autoconfig messages 140 141## `INSECURE' turns off the kernel security level (securelevel = 0 always). 142## This allows writing to /dev/mem, loading kernel modules while multi-user, 143## and other insecurities good only for development work. Do not use this 144## option on a production machine. 145#options INSECURE 146 147## `FDSCRIPTS' allows non-readable but executable scripts by providing a 148## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 149## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 150## opaque file mechanism. Perl calls this "secure setuid scripts." 151 152#options FDSCRIPTS 153#options SETUIDSCRIPTS 154 155## Options for compatibility with previous releases foreign system binaries. 156## In the cases of COMPAT_SUNOS, you may need to set up additional user-level 157## utilities or system configuration files. See compat_sunos(8). 158 159include "conf/compat_netbsd10.config" 160options COMPAT_SUNOS # SunOS 4.x binary compatibility 161 162## File systems. You probably need at least one of FFS or NFS. 163file-system FFS # Berkeley Fast Filesystem 164file-system NFS # Sun NFS-compatible filesystem client 165file-system KERNFS # kernel data-structure filesystem 166file-system NULLFS # NULL layered filesystem 167file-system OVERLAY # overlay file system 168file-system MFS # memory-based filesystem 169file-system FDESC # user file descriptor filesystem 170file-system UMAPFS # uid/gid remapping filesystem 171file-system LFS # Log-based filesystem (still experimental) 172file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 173file-system PROCFS # /proc 174file-system CD9660 # ISO 9660 + Rock Ridge file system 175file-system UNION # union file system 176file-system MSDOSFS # MS-DOS FAT filesystem(s). 177file-system CODA # Coda File System; also needs vcoda (below) 178file-system PTYFS # /dev/pts/N support 179file-system TMPFS # Efficient memory file-system 180#file-system UDF # experimental - OSTA UDF CD/DVD file-system 181 182## File system options. 183options NFSSERVER # Sun NFS-compatible filesystem server 184options QUOTA # FFS quotas 185#options QUOTA2 # new, in-filesystem UFS quotas 186#options FFS_EI # FFS Endian Independent support 187options WAPBL # File system journaling support 188#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 189#options FFS_NO_SNAPSHOT # No FFS snapshot support 190options UFS_EXTATTR # Extended attribute support for UFS1 191 192## Network protocol support. In most environments, INET is required. 193options INET # IP (Internet Protocol) v4 194options INET6 # IPV6 195#options IPSEC # IP security 196#options IPSEC_DEBUG # debug for IP security 197#options GATEWAY # packet forwarding ("router switch") 198#options MROUTING # packet forwarding of multicast packets 199#options PIM # Protocol Independent Multicast 200#options NETATALK # AppleTalk (over Ethernet) protocol 201options NTP # Network Time Protocol in-kernel support 202#options PPS_SYNC # Add serial line synchronization for NTP 203options PPP_BSDCOMP # Add BSD compression to ppp device 204options PPP_DEFLATE # Add deflate (libz) compression to ppp device 205options PPP_FILTER # Add active filters for ppp (via bpf) 206 207#options ALTQ # Manipulate network interfaces' output queues 208#options ALTQ_BLUE # Stochastic Fair Blue 209#options ALTQ_CBQ # Class-Based Queueing 210#options ALTQ_CDNR # Diffserv Traffic Conditioner 211#options ALTQ_FIFOQ # First-In First-Out Queue 212#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 213#options ALTQ_HFSC # Hierarchical Fair Service Curve 214#options ALTQ_LOCALQ # Local queueing discipline 215#options ALTQ_PRIQ # Priority Queueing 216#options ALTQ_RED # Random Early Detection 217#options ALTQ_RIO # RED with IN/OUT 218#options ALTQ_WFQ # Weighted Fair Queueing 219 220 221 222#### Main bus and CPU .. all systems. 223mainbus0 at root 224cpu0 at mainbus0 225cpuunit0 at mainbus0 # sun4d 226cpuunit* at mainbus0 # sun4d 227cpu0 at cpuunit0 # sun4d 228 229#### SX rendering engine found in SS20 and SS10SX 230sx0 at mainbus0 231 232#### Bus types found on SPARC systems. 233 234sbus0 at mainbus0 # sun4c 235obio0 at mainbus0 # sun4 and sun4m 236sparcvme0 at mainbus0 # sun4 237iommu0 at mainbus0 # sun4m 238sbus0 at iommu0 # sun4m 239sparcvme0 at iommu0 # sun4m 240vme0 at sparcvme0 # MI VME attachment 241bootbus0 at cpuunit0 # sun4d 242bootbus* at cpuunit? # sun4d 243 244## SBus expander box 245xbox* at sbus? slot ? offset ? 246sbus* at xbox? 247 248## SBus to PCMCIA bridge 249nell* at sbus? slot ? offset ? # PCMCIA bridge 250pcmcia* at nell? 251tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 252pcmcia* at tslot? 253 254#### Standard system devices -- all required for a given architecture 255 256## Auxiliary system registers on sun4c and sun4m 257auxreg0 at mainbus0 # sun4c 258auxreg0 at obio0 # sun4m 259auxiotwo0 at obio0 # only on Tadpole SPARCbook. 260 261## Power status and control register on Sun4m systems 262power0 at obio0 263 264## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 265## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 266clock0 at mainbus0 # sun4c 267clock0 at obio0 # sun4m 268clock0 at obio0 addr 0xf2000000 # sun4/300 269clock0 at bootbus0 # sun4d 270 271## Intersil clock found on 4/100 and 4/200 systems. 272oclock0 at obio0 addr 0xf3000000 # sun4/200 273oclock0 at obio0 addr 0x03000000 # sun4/100 274 275## Memory error registers. 276memreg0 at mainbus0 # sun4c 277memreg0 at obio0 # sun4m 278memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 279memreg0 at obio0 addr 0x04000000 # sun4/100 280 281## ECC memory control 282eccmemctl0 at mainbus0 # sun4m 283 284## Timer chip found on 4/300, sun4c, and sun4m systems. 285timer0 at mainbus0 # sun4c 286timer0 at obio0 # sun4m 287timer0 at obio0 addr 0xef000000 # sun4/300 288 289## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 290## doesn't use this driver; the `EEPROM' is in the NVRAM on the 291## Mostek clock chip on 4/300 systems. 292eeprom0 at obio0 addr 0xf2000000 # sun4/200 293eeprom0 at obio0 addr 0x02000000 # sun4/100 294 295 296#### Serial port configuration 297 298## Zilog 8530 serial chips. Each has two-channels. 299## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 300zs0 at mainbus0 # sun4c 301zs0 at obio0 # sun4m 302zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 303zs0 at obio0 addr 0x01000000 level 12 # sun4/100 304zs0 at bootbus0 # sun4d 305zstty0 at zs0 channel 0 # ttya 306zstty1 at zs0 channel 1 # ttyb 307 308zs1 at mainbus0 # sun4c 309zs1 at obio0 # sun4m 310zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 311zs1 at obio0 addr 0x00000000 level 12 # sun4/100 312zs1 at bootbus0 # sun4d 313 314# old kbd and mouse attachments 315#kbd0 at zs1 channel 0 # keyboard 316#ms0 at zs1 channel 1 # mouse 317zstty* at zs? 318 319# these are for wscons 320kbd0 at zstty? 321ms0 at zstty? 322wskbd* at wskbddev? 323wsmouse* at wsmousedev? 324 325zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 326zstty2 at zs2 channel 0 # ttyc 327zstty3 at zs2 channel 1 # ttyd 328 329zs* at bootbus? # sun4d 330zstty* at zs? 331 332## NS16x50 serial chips and clones. Present on the 333## Sun JavaStation-1 and Tadpole SPARCbook 3 334com* at obio0 # sun4m 335 336# Parallel port. 337bpp* at sbus? slot? offset ? 338 339## Magma Serial/Parallel driver 340magma* at sbus? slot ? offset ? 341mtty* at magma? 342mbpp* at magma? 343 344## SUNW,spif Serial/Parallel driver 345spif* at sbus? slot ? offset ? 346stty* at spif? 347sbpp* at spif? 348 349## PCMCIA serial interfaces 350#com* at pcmcia? 351#pcmcom* at pcmcia? 352#com* at pcmcom? 353 354#### Disk controllers and disks 355 356# 357 358## The following flags may be set for the NCR53c94 based esp driver: 359## bits 0-7: disable disconnect/reselect for the corresponding target 360## bits 8-15: disable synchronous negotiation for target [bit-8] 361 362## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 363## Both `dma' and `esp' are needed in all cases. 364## Two kinds of additional SBus SCSI interfaces are available. One uses 365## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 366 367## sun4/300 SCSI - an NCR53c94 or equivalent behind 368## an LSI Logic DMA controller 369 370dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 371esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 372 373dma0 at sbus0 slot ? offset ? # sun4c/sun4m 374esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 375esp0 at dma0 flags 0x0000 # sun4m 376 377# FSBE/S SCSI & SunSwift Sbus FAS366 378dma* at sbus? slot ? offset ? # SBus 379esp* at sbus? slot ? offset ? flags 0x0000 # SBus 380esp* at dma? flags 0x0000 # SBus 381 382scsibus* at esp? 383 384## Qlogic ISP SBus SCSI Card 385isp* at sbus? slot ? offset ? 386scsibus* at isp? 387 388## NCR5380-based "Sun SCSI 3" VME SCSI controller. 389## This driver has several flags which may be enabled by OR'ing 390## the values and using the "flags" directive. 391## Valid flags are: 392## 393## 0x01 Use DMA (may be polled) 394## 0x02 Use DMA completion interrupts 395## 0x04 Allow disconnect/reselect 396## 397## E.g. the following would enable DMA, interrupts, and reselect: 398## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 399## 400## By default, DMA is enabled in the driver. 401 402si0 at vme0 addr 0x200000 irq 2 vect 0x40 403scsibus* at si? 404 405## NCR5380-based "SCSI Weird" on-board SCSI interface found 406## on sun4/100 systems. The flags are the same as the "si" 407## controller. Note, while DMA is enabled by default, only 408## polled DMA works at this time, and reselects do not work 409## on this particular controller. 410 411sw0 at obio0 addr 0x0a000000 level 3 412scsibus* at sw? 413 414## PCMCIA SCSI controllers 415#aic* at pcmcia? 416#spc* at pcmcia? 417#scsibus* at aic? 418#scsibus* at spc? 419 420 421## These entries find devices on all SCSI busses and assign 422## unit numbers dynamically. 423sd* at scsibus? target ? lun ? # SCSI disks 424st* at scsibus? target ? lun ? # SCSI tapes 425cd* at scsibus? target ? lun ? # SCSI CD-ROMs 426ch* at scsibus? target ? lun ? # SCSI changer devices 427ss* at scsibus? target ? lun ? # SCSI scanners 428ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 429uk* at scsibus? target ? lun ? # unknown SCSI 430 431 432## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 433## on sun4 systems. 434xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 435xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 436xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 437xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 438xd* at xdc? drive ? 439 440## Xylogics 451 or 451 VME SMD disk controllers and disks, found 441## on sun4 systems. 442xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 443xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 444xy* at xyc? drive ? 445 446 447## Floppy controller and drive found on SPARCstations. 448 449fdc0 at mainbus0 # sun4c controller 450fdc0 at obio0 # sun4m controller 451fd* at fdc0 # the drive itself 452 453## PCMCIA IDE controllers 454#wdc* at pcmcia? 455#atabus* at ata? 456#wd* at atabus? drive ? flags 0x0000 457 458## A disk-like interface to files. Can be used to create floppy, CD, 459## miniroot images, etc. 460 461pseudo-device vnd 462#options VND_COMPRESSION # compressed vnd(4) 463 464## Concatenated and striped disks; with this, you can create a software-based 465## disk array similar to a "RAID 0" setup. See ccd(4). 466 467pseudo-device ccd 468 469## Cryptographic disk devices; See cgd(4) 470 471#pseudo-device cgd 472 473## RAIDframe disk driver: software RAID driver. See raid(4). 474 475pseudo-device raid 476options RAID_AUTOCONFIG # auto-configuration of RAID components 477# Options to enable various other RAIDframe RAID types. 478# options RF_INCLUDE_EVENODD=1 479# options RF_INCLUDE_RAID5_RS=1 480# options RF_INCLUDE_PARITYLOGGING=1 481# options RF_INCLUDE_CHAINDECLUSTER=1 482# options RF_INCLUDE_INTERDECLUSTER=1 483# options RF_INCLUDE_PARITY_DECLUSTERING=1 484# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 485 486 487## Memory disk device, used on boot floppies with compressed 488## kernel-plus-root-disk images. 489 490#pseudo-device md 491 492 493#### Network interfaces 494 495## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 496## Three flavors of additional SBus ethernets are available. One attaches 497## directly like the sun4c on-board, one uses the ledma device like the 498## sun4m on-board, and one uses the lebuffer device. 499 500le0 at obio0 addr 0xf9000000 level 6 # sun4/300 501le0 at sbus0 slot ? offset ? # sun4c on-board 502ledma0 at sbus0 slot ? offset ? # sun4m on-board 503le0 at ledma0 # sun4m on-board 504le* at sbus? slot ? offset ? # SBus 505ledma* at sbus? slot ? offset ? # SBus 506le* at ledma? # SBus 507lebuffer0 at sbus? slot ? offset ? # SBus 508le0 at lebuffer? # SBus 509lebuffer* at sbus? slot ? offset ? # SBus 510le* at lebuffer? # SBus 511 512 513## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 514## or on a Multibus/VME card. 515ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 516ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 517## VME: the first [addr,len] pair specifies the device registers; 518## the second pair specifies the on-board memory buffer 519ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 520ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 521ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 522ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 523 524## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 525## (qe, 10MBd) attached. 526qec* at sbus? slot ? offset ? # Quad Ethernet Controller 527be* at qec? # BigMac Ethernet (10/100MBd) 528qe* at qec? # Mace Ethernet (10MBd) 529 530## Happy Meal Ethernet 531hme* at sbus? slot ? offset ? 532 533# PCMCIA ethernet devices 534#ep* at pcmcia? 535#mbe* at pcmcia? 536#ne* at pcmcia? 537#sm* at pcmcia? 538 539## PCMCIA wavelan card 540#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 541 542# MII/PHY support 543exphy* at mii? phy ? # 3Com internal PHYs 544icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 545inphy* at mii? phy ? # Intel 82555 PHYs 546lxtphy* at mii? phy ? # Level One LXT-970 PHYs 547nsphy* at mii? phy ? # NS83840 PHYs 548qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 549sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 550tlphy* at mii? phy ? # ThunderLAN PHYs 551ukphy* at mii? phy ? # generic unknown PHYs 552 553## Loopback network interface; required 554pseudo-device loop 555 556## SLIP and CSLIP interfaces, for IP over a serial line. 557pseudo-device sl 558 559## PPP, the successor to SLIP. See pppd(8). 560pseudo-device ppp 561 562## PPP over Ethernet (RFC 2516) 563pseudo-device pppoe 564 565## Starmode Radio IP, a special hardware network device. 566#pseudo-device strip 567 568## Network "tunnel" device, allowing protocol stacks to run in the userland. 569## This is used by the third-party user-mode "ppp" program, and others. 570pseudo-device tun 571pseudo-device tap # virtual Ethernet 572 573## Generic L3 over IP tunnel 574#pseudo-device gre # generic L3 over IP tunnel 575 576## Berkeley Packet Filter, required to run RARPD. A generic C-language 577## interface that allows selective examining of incoming packets. 578pseudo-device bpfilter 579 580pseudo-device carp # Common Address Redundancy Protocol 581 582pseudo-device npf # NPF packet filter 583 584## for IPv6 585pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 586#pseudo-device faith # IPv[46] tcp relay translation i/f 587pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 588 589## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 590pseudo-device vlan 591 592## Simple inter-network traffic bridging 593pseudo-device bridge 594#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 595pseudo-device agr # IEEE 802.3ad link aggregation 596 597## accept filters 598pseudo-device accf_data # "dataready" accept filter 599pseudo-device accf_http # "httpready" accept filter 600 601#### Audio and video devices 602 603## /dev/audio support (`audioamd' plus `audio') 604## 605audioamd0 at mainbus0 # sun4c 606audioamd0 at obio0 # sun4m 607audioamd0 at sbus0 slot ? offset ? # sun4m 608 609audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 610 611#options DBRI_DEBUG # noisy debug output from the dbri driver 612dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 613 614audio* at audiobus? 615 616## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 617## systems. If your sun4 system has a cgfour installed in the P4 slot, 618## the P4 entries for "bwtwo" will attach to the overlay plane of the 619## "cgfour". 620 621bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 622bwtwo* at sbus? slot ? offset ? # 623bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 624bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 625bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 626 627## Sun "cgtwo" VME color framebuffer 628# XXX no wsdisplay support 629#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 630 631## Sun "cgthree" Sbus color framebuffer 632cgthree0 at sbus? slot ? offset ? 633cgthree* at sbus? slot ? offset ? 634 635## Sun "cgfour" color framebuffer with overlay plane. See above comment 636## regarding overlay plane. 637# XXX no wsdisplay support 638#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 639#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 640 641## Sun "cgsix" accelerated color framebuffer. 642cgsix0 at sbus? slot ? offset ? 643cgsix* at sbus? slot ? offset ? 644cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 645cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 646 647## Sun "cgeight" 24-bit framebuffer 648# XXX no wsdisplay support 649#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 650#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 651 652## Sun "tcx" accelerated color framebuffer. 653# there can be only one 654tcx0 at sbus? slot ? offset ? 655 656## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 657cgtwelve* at sbus? slot ? offset ? 658# the driver can use the color framebuffer or the monochrome overlay 659# the latter is faster 660options CG12_COLOR 661 662# Sun "cgfourteen" accelerated 24-bit framebuffer. 663cgfourteen* at obio0 # sun4m 664 665# P9100-based display on Tadpole SPARCbook 3. 666pnozz0 at sbus? slot ? offset ? 667# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 668# 'latched in' but at least my 3GX works happily without 669# Enable it by default since we don't know which hardware really needs it. 670options PNOZZ_USE_LATCH 671 672# Sun ZX/Leo 24-bit framebuffer 673zx* at sbus? slot ? offset ? 674 675# Fujitsu AG-10e accelerated graphics 8/24-bit board 676agten* at sbus? slot ? offset ? 677 678## Southland Media Systems (now Quantum 3D) MGX 679mgx* at sbus? slot ? offset ? 680 681# generic framebuffer console 682genfb* at sbus? slot ? offset ? 683 684# make sure wsdisplay0 is the console 685wsdisplay0 at wsemuldisplaydev? console 1 686wsdisplay* at wsemuldisplaydev? 687 688#### Other device configuration 689 690# Tadpole microcontroller 691tctrl0 at obio0 692 693# Aurora Personality Chip (APC) on SPARCstation-4/5 694# Not enabled by default as it may hang some systems 695#apc* at sbus? slot ? offset ? 696 697## Pseudo ttys, required for network logins and programs like screen. 698 699pseudo-device pty # pseudo-terminals 700 701## Random device, used to implement /dev/random (a source of random noise), 702## and generate randomness for some kernel formulae. 703 704 705# a pseudo device needed for Coda # also needs CODA (above) 706pseudo-device vcoda # coda minicache <-> venus comm. 707 708pseudo-device clockctl # user control of clock subsystem 709pseudo-device drvctl # user control of drive subsystem 710pseudo-device ksyms # /dev/ksyms 711pseudo-device fss # file system snapshot device 712pseudo-device wsmux # mouse and keyboard multiplexor 713pseudo-device wsfont 714pseudo-device putter # for puffs and pud 715 716include "dev/veriexec.config" 717 718#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 719 # (for static binaries only for now) 720