xref: /netbsd-src/sys/arch/sparc/conf/GENERIC (revision 200d779b75dbeafa7bc01fd0f60bc61185f6967b)
1# $NetBSD: GENERIC,v 1.248 2014/11/16 16:01:43 manu Exp $
2#
3# GENERIC machine description file
4#
5# This machine description file is used to generate the default NetBSD
6# kernel.  The generic kernel does not include all options, subsystems
7# and device drivers, but should be useful for most applications.
8#
9# The machine description file can be customised for your specific
10# machine to reduce the kernel size and improve its performance.
11#
12# For further information on compiling NetBSD kernels, see the config(8)
13# man page.
14#
15# For further information on hardware support for this architecture, see
16# the intro(4) man page.  For further information about kernel options
17# for this architecture, see the options(4) man page.  For an explanation
18# of each device driver in this file see the section 4 man page for the
19# device.
20
21include 	"arch/sparc/conf/std.sparc"
22
23options 	INCLUDE_CONFIG_FILE	# embed config file in kernel binary
24
25#ident 		"GENERIC-$Revision: 1.248 $"
26
27maxusers	32
28
29## System kernel configuration.  See options(4) for more detail.
30
31
32# Options for variants of the Sun SPARC architecure.
33# We currently support three architecture types; at least one is required.
34options 	SUN4		# sun4/100, sun4/200, sun4/300
35options 	SUN4C		# sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc.
36options 	SUN4M		# sun4m - SS10, SS20, Classic, etc.
37options 	SUN4D		# sun4d - SS1000, SC2000
38
39options 	SUN4_MMU3L	# sun4/400 3-level MMU
40
41## System options specific to the sparc machine type
42
43# Blink the power LED on some machines to indicate the system load.
44#options 	BLINK
45
46## Use a faster console than the PROM's slow drawing routines.  Not needed
47## for headless (no framebuffer) machines.
48## These is obsolete for wscons kernels
49#options 	RASTERCONSOLE		# fast rasterop console
50#options 	RASTERCONSOLE_FGCOL=WSCOL_BLACK
51#options 	RASTERCONSOLE_BGCOL=WSCOL_WHITE
52
53# wscons stuff
54#options 	WSEMUL_SUN
55options 	WSEMUL_VT100
56options 	WSDISPLAY_COMPAT_RAWKBD
57options 	WSDISPLAY_CUSTOM_OUTPUT
58options 	WS_DEFAULT_FG=WSCOL_BLACK
59options 	WS_DEFAULT_BG=WSCOL_LIGHT_WHITE
60options 	WS_KERNEL_FG=WSCOL_GREEN
61options 	WS_KERNEL_BG=WSCOL_LIGHT_WHITE
62options 	WSDISPLAY_COMPAT_PCVT
63options 	WSDISPLAY_COMPAT_SYSCONS
64options 	WSDISPLAY_COMPAT_USL		# wsconscfg VT handling
65
66options 	WSDISPLAY_SCROLLSUPPORT
67
68# generic options vlid for both wscons and RASTERCONSOLE
69options 	FONT_GALLANT12x22	# the console font
70options 	FONT_BOLD8x16		# a somewhat smaller font
71
72#### System options that are the same for all ports
73
74## Root device configuration: change the ?'s if you are going to use a
75## nonstandard root partition (other than where the kernel is booted from)
76## and/or nonstandard root type (not ffs or nfs).  Normally this can be
77## automagically determined at boot time.
78
79config		netbsd	root on ? type ?
80
81## System call tracing (see ktrace(1)).
82options 	KTRACE
83
84## Collect statistics on kernel malloc's and free's.  This does have a
85## significant performance hit on slower machines, so it is intended for
86## diagnostic use only.
87#options 	KMEMSTATS
88
89## System V compatible IPC subsystem.  (msgctl(2), semctl(2), and shmctl(2))
90options 	SYSVMSG		# System V message queues
91options 	SYSVSEM		# System V semaphores
92options 	SYSVSHM		# System V shared memory
93
94options 	MODULAR		# new style module(7) framework
95options 	MODULAR_DEFAULT_AUTOLOAD
96
97options 	USERCONF	# userconf(4) support
98#options 	PIPE_SOCKETPAIR	# smaller, but slower pipe(2)
99options 	SYSCTL_INCLUDE_DESCR	# Include sysctl descriptions in kernel
100
101# Enable experimental buffer queue strategy for better responsiveness under
102# high disk I/O load. Use it with caution - it's not proven to be stable yet.
103#options 	BUFQ_READPRIO
104#options 	BUFQ_PRIOCSCAN
105
106## NFS boot options; tries DHCP/BOOTP then BOOTPARAM
107options 	NFS_BOOT_BOOTPARAM
108#options 	NFS_BOOT_BOOTP
109options 	NFS_BOOT_DHCP
110
111#### Debugging options
112
113## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
114## serial console break or keyboard reset, where the PROM would normally
115## intercept.  DDB_HISTORY_SIZE adds up/down arrow command history.
116options 	DDB			# kernel dynamic debugger
117options 	DDB_HISTORY_SIZE=100	# enable history editing in DDB
118#options 	DDB_ONPANIC=1		# see also sysctl(7): `ddb.onpanic'
119
120## You may also use gdb, on another computer connected to this machine over
121## a serial port.  Both KGDB_DEV and KGDB_DEVRATE should be specified;
122## KGDB_DEV is a dev_t encoded device number of the serial port to use, where
123## the minor device number encodes the PROM enumeration of the serial ports,
124## i.e.:
125## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd.
126## (Note: ttyc and ttyd are available only on some sun4 models)
127#options 	KGDB			# support for kernel gdb
128#options 	KGDB_DEV=0xc01		# kgdb device number (this is `ttyb')
129#options 	KGDB_DEVRATE=38400	# baud rate
130
131
132## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
133## such that gdb(1) can be used on a kernel coredump.
134
135#makeoptions	DEBUG="-g"
136
137
138## Adds code to the kernel that does internal consistency checks, and will
139## cause the kernel to panic if corruption of internal data structures
140## is detected.
141#options 	DIAGNOSTIC	# extra kernel sanity checking
142
143## Enable (possibly expensive) debugging code that may also display messages
144## on the system console
145#options 	DEBUG
146#options 	LOCKDEBUG
147#options 	SYSCALL_DEBUG
148
149## Make SCSI error messages more verbose when explaining their meanings.
150options 	SCSIVERBOSE
151
152options 	MIIVERBOSE	# verbose PHY autoconfig messages
153
154## `INSECURE' turns off the kernel security level (securelevel = 0 always).
155## This allows writing to /dev/mem, loading kernel modules while multi-user,
156## and other insecurities good only for development work.  Do not use this
157## option on a production machine.
158#options 	INSECURE
159
160## `FDSCRIPTS' allows non-readable but executable scripts by providing a
161## pre-opened opaque file to the script interpreter.  `SETUIDSCRIPTS',
162## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
163## opaque file mechanism.  Perl calls this "secure setuid scripts."
164
165#options 	FDSCRIPTS
166#options 	SETUIDSCRIPTS
167
168## Options for compatibility with previous releases foreign system binaries.
169## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
170## additional user-level utilities or system configuration files. See
171## compat_sunos(8) and compat_svr4(8).
172
173options 	COMPAT_43	# 4.3BSD system interfaces
174options 	COMPAT_10	# NetBSD 1.0,
175options 	COMPAT_11	# NetBSD 1.1,
176options 	COMPAT_12	# NetBSD 1.2,
177options 	COMPAT_13	# NetBSD 1.3,
178options 	COMPAT_14	# NetBSD 1.4,
179options 	COMPAT_15	# NetBSD 1.5,
180options 	COMPAT_16	# NetBSD 1.6,
181options 	COMPAT_20	# NetBSD 2.0,
182options 	COMPAT_30	# NetBSD 3.0,
183options 	COMPAT_40	# NetBSD 4.0,
184options 	COMPAT_50	# NetBSD 5.0,
185options 	COMPAT_60	# NetBSD 6.0, and
186options 	COMPAT_70	# NetBSD 7.0 binary compatibility
187options 	COMPAT_SUNOS	# SunOS 4.x binary compatibility
188options 	COMPAT_SVR4	# SunOS 5.x binary compatibility
189options 	COMPAT_BSDPTY	# /dev/[pt]ty?? ptys.
190
191## File systems.  You probably need at least one of FFS or NFS.
192file-system	FFS		# Berkeley Fast Filesystem
193file-system	NFS		# Sun NFS-compatible filesystem client
194file-system	KERNFS		# kernel data-structure filesystem
195file-system	NULLFS		# NULL layered filesystem
196file-system 	OVERLAY		# overlay file system
197file-system	MFS		# memory-based filesystem
198file-system	FDESC		# user file descriptor filesystem
199file-system	UMAPFS		# uid/gid remapping filesystem
200file-system	LFS		# Log-based filesystem (still experimental)
201file-system	PUFFS		# Userspace file systems (e.g. ntfs-3g & sshfs)
202file-system	PROCFS		# /proc
203file-system	CD9660		# ISO 9660 + Rock Ridge file system
204file-system	UNION		# union file system
205file-system	MSDOSFS		# MS-DOS FAT filesystem(s).
206file-system	CODA		# Coda File System; also needs vcoda (below)
207file-system	PTYFS		# /dev/pts/N support
208file-system	TMPFS		# Efficient memory file-system
209#file-system	UDF		# experimental - OSTA UDF CD/DVD file-system
210
211## File system options.
212options 	NFSSERVER	# Sun NFS-compatible filesystem server
213options 	QUOTA		# FFS quotas
214#options 	FFS_EI		# FFS Endian Independent support
215options 	WAPBL		# File system journaling support
216#options 	UFS_DIRHASH	# UFS Large Directory Hashing - Experimental
217#options 	FFS_NO_SNAPSHOT	# No FFS snapshot support
218options 	UFS_EXTATTR	# Extended attribute support for UFS1
219
220## Network protocol support.  In most environments, INET is required.
221options 	INET		# IP (Internet Protocol) v4
222options 	INET6		# IPV6
223#options 	IPSEC		# IP security
224#options 	IPSEC_DEBUG	# debug for IP security
225#options 	GATEWAY		# packet forwarding ("router switch")
226#options 	MROUTING	# packet forwarding of multicast packets
227#options 	PIM		# Protocol Independent Multicast
228#options 	DIRECTED_BROADCAST	# allow broadcasts through routers
229#options 	NETATALK	# AppleTalk (over Ethernet) protocol
230options 	NTP		# Network Time Protocol in-kernel support
231#options 	PPS_SYNC	# Add serial line synchronization for NTP
232options 	IPFILTER_LOG	# Add ipmon(8) logging for ipfilter device
233options 	IPFILTER_LOOKUP	# ippool(8) support
234options 	IPFILTER_COMPAT # Compat for IP-Filter
235#options 	IPFILTER_DEFAULT_BLOCK	# block all packets by default
236options 	PPP_BSDCOMP	# Add BSD compression to ppp device
237options 	PPP_DEFLATE	# Add deflate (libz) compression to ppp device
238options 	PPP_FILTER	# Add active filters for ppp (via bpf)
239
240#options 	ALTQ		# Manipulate network interfaces' output queues
241#options 	ALTQ_BLUE	# Stochastic Fair Blue
242#options 	ALTQ_CBQ	# Class-Based Queueing
243#options 	ALTQ_CDNR	# Diffserv Traffic Conditioner
244#options 	ALTQ_FIFOQ	# First-In First-Out Queue
245#options 	ALTQ_FLOWVALVE	# RED/flow-valve (red-penalty-box)
246#options 	ALTQ_HFSC	# Hierarchical Fair Service Curve
247#options 	ALTQ_LOCALQ	# Local queueing discipline
248#options 	ALTQ_PRIQ	# Priority Queueing
249#options 	ALTQ_RED	# Random Early Detection
250#options 	ALTQ_RIO	# RED with IN/OUT
251#options 	ALTQ_WFQ	# Weighted Fair Queueing
252
253
254
255#### Main bus and CPU .. all systems.
256mainbus0 at root
257cpu0	at mainbus0
258cpuunit0	at mainbus0			# sun4d
259cpuunit*	at mainbus0			# sun4d
260cpu0	at cpuunit0				# sun4d
261
262#### SX rendering engine found in SS20 and SS10SX
263sx0	at mainbus0
264
265#### Bus types found on SPARC systems.
266
267sbus0	at mainbus0				# sun4c
268obio0	at mainbus0				# sun4 and sun4m
269sparcvme0	at mainbus0			# sun4
270iommu0	at mainbus0				# sun4m
271sbus0	at iommu0				# sun4m
272sparcvme0	at iommu0			# sun4m
273vme0	at sparcvme0				# MI VME attachment
274bootbus0	at cpuunit0			# sun4d
275bootbus*	at cpuunit?			# sun4d
276
277## SBus expander box
278xbox*	at sbus? slot ? offset ?
279sbus*	at xbox?
280
281## SBus to PCMCIA bridge
282nell*	at sbus? slot ? offset ?		# PCMCIA bridge
283pcmcia*	at nell?
284tslot*	at sbus? slot ? offset ?		# PCMCIA bridge (tadpole 3gx)
285pcmcia*	at tslot?
286
287#### Standard system devices -- all required for a given architecture
288
289## Auxiliary system registers on sun4c and sun4m
290auxreg0	at mainbus0				# sun4c
291auxreg0	at obio0				# sun4m
292auxiotwo0 at obio0				# only on Tadpole SPARCbook.
293
294## Power status and control register on Sun4m systems
295power0	at obio0
296
297## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems.
298## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
299clock0	at mainbus0				# sun4c
300clock0	at obio0				# sun4m
301clock0	at obio0 addr 0xf2000000		# sun4/300
302clock0	at bootbus0				# sun4d
303
304## Intersil clock found on 4/100 and 4/200 systems.
305oclock0	at obio0 addr 0xf3000000		# sun4/200
306oclock0	at obio0 addr 0x03000000		# sun4/100
307
308## Memory error registers.
309memreg0	at mainbus0				# sun4c
310memreg0	at obio0				# sun4m
311memreg0	at obio0 addr 0xf4000000		# sun4/200 and sun4/300
312memreg0	at obio0 addr 0x04000000		# sun4/100
313
314## ECC memory control
315eccmemctl0 at mainbus0				# sun4m
316
317## Timer chip found on 4/300, sun4c, and sun4m systems.
318timer0	at mainbus0				# sun4c
319timer0	at obio0				# sun4m
320timer0	at obio0 addr 0xef000000		# sun4/300
321
322## EEPROM found on 4/100 and 4/200 systems.  Note that the 4/300
323## doesn't use this driver; the `EEPROM' is in the NVRAM on the
324## Mostek clock chip on 4/300 systems.
325eeprom0	at obio0 addr 0xf2000000		# sun4/200
326eeprom0	at obio0 addr 0x02000000		# sun4/100
327
328
329#### Serial port configuration
330
331## Zilog 8530 serial chips.  Each has two-channels.
332## zs0 is ttya and ttyb.  zs1 is the keyboard and mouse.
333zs0	at mainbus0					# sun4c
334zs0	at obio0					# sun4m
335zs0	at obio0 addr 0xf1000000 level 12		# sun4/200 and sun4/300
336zs0	at obio0 addr 0x01000000 level 12		# sun4/100
337zs0	at bootbus0					# sun4d
338zstty0	at zs0 channel 0				# ttya
339zstty1	at zs0 channel 1				# ttyb
340
341zs1	at mainbus0					# sun4c
342zs1	at obio0					# sun4m
343zs1	at obio0 addr 0xf0000000 level 12		# sun4/200 and sun4/300
344zs1	at obio0 addr 0x00000000 level 12		# sun4/100
345zs1	at bootbus0					# sun4d
346
347# old kbd and mouse attachments
348#kbd0	at zs1 channel 0				# keyboard
349#ms0	at zs1 channel 1				# mouse
350zstty*	at zs?
351
352# these are for wscons
353kbd0	at zstty?
354ms0	at zstty?
355wskbd*	at wskbddev?
356wsmouse* 	at wsmousedev?
357
358zs2	at obio0 addr 0xe0000000 level 12		# sun4/300
359zstty2	at zs2 channel 0				# ttyc
360zstty3	at zs2 channel 1				# ttyd
361
362zs*	at bootbus?					# sun4d
363zstty*	at zs?
364
365## NS16x50 serial chips and clones.  Present on the
366## Sun JavaStation-1 and Tadpole SPARCbook 3
367com*	at obio0					# sun4m
368
369# Parallel port.
370bpp*	at sbus? slot? offset ?
371
372## Magma Serial/Parallel driver
373magma*	at sbus? slot ? offset ?
374mtty*	at magma?
375mbpp*	at magma?
376
377## SUNW,spif Serial/Parallel driver
378spif*  at sbus? slot ? offset ?
379stty*  at spif?
380sbpp*  at spif?
381
382## PCMCIA serial interfaces
383#com*	at pcmcia?
384#pcmcom*	at pcmcia?
385#com*	at pcmcom?
386
387#### Disk controllers and disks
388
389#
390
391## The following flags may be set for the NCR53c94 based esp driver:
392##	bits 0-7:  disable disconnect/reselect for the corresponding target
393##	bits 8-15: disable synchronous negotiation for target [bit-8]
394
395## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards.
396## Both `dma' and `esp' are needed in all cases.
397## Two kinds of additional SBus SCSI interfaces are available.  One uses
398## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
399
400## sun4/300 SCSI - an NCR53c94 or equivalent behind
401## an LSI Logic DMA controller
402
403dma0	at obio0 addr 0xfa001000 level 4		# sun4/300
404esp0	at obio0 addr 0xfa000000 level 4 flags 0x0000	# sun4/300
405
406dma0	at sbus0 slot ? offset ?			# sun4c/sun4m
407esp0	at sbus0 slot ? offset ? flags 0x0000		# sun4c
408esp0	at dma0 flags 0x0000				# sun4m
409
410# FSBE/S SCSI & SunSwift Sbus FAS366
411dma*	at sbus? slot ? offset ?			# SBus
412esp*	at sbus? slot ? offset ? flags 0x0000		# SBus
413esp*	at dma? flags 0x0000				# SBus
414
415scsibus* at esp?
416
417## Qlogic ISP SBus SCSI Card
418isp*	at sbus? slot ? offset ?
419scsibus* at isp?
420
421## NCR5380-based "Sun SCSI 3" VME SCSI controller.
422## This driver has several flags which may be enabled by OR'ing
423## the values and using the "flags" directive.
424## Valid flags are:
425##
426##	0x01		Use DMA (may be polled)
427##	0x02		Use DMA completion interrupts
428##	0x04		Allow disconnect/reselect
429##
430## E.g. the following would enable DMA, interrupts, and reselect:
431## si0	at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07
432##
433## By default, DMA is enabled in the driver.
434
435si0	at vme0 addr 0x200000 irq 2 vect 0x40
436scsibus* at si?
437
438## NCR5380-based "SCSI Weird" on-board SCSI interface found
439## on sun4/100 systems.  The flags are the same as the "si"
440## controller.  Note, while DMA is enabled by default, only
441## polled DMA works at this time, and reselects do not work
442## on this particular controller.
443
444sw0	at obio0 addr 0x0a000000 level 3
445scsibus* at sw?
446
447## PCMCIA SCSI controllers
448#aic*	at pcmcia?
449#spc*	at pcmcia?
450#scsibus* at aic?
451#scsibus* at spc?
452
453
454## These entries find devices on all SCSI busses and assign
455## unit numbers dynamically.
456sd*	at scsibus? target ? lun ?		# SCSI disks
457st*	at scsibus? target ? lun ?		# SCSI tapes
458cd*	at scsibus? target ? lun ?		# SCSI CD-ROMs
459ch*	at scsibus? target ? lun ?		# SCSI changer devices
460ss*	at scsibus? target ? lun ?		# SCSI scanners
461ses*	at scsibus? target ? lun ?		# SCSI SES/SAF-TE
462uk*	at scsibus? target ? lun ?		# unknown SCSI
463
464
465## Xylogics 753 or 7053 VME SMD disk controllers and disks, found
466## on sun4 systems.
467xdc0	at vme0 addr 0xee80 irq 3 vect 0x44
468xdc1	at vme0 addr 0xee90 irq 3 vect 0x45
469xdc2	at vme0 addr 0xeea0 irq 3 vect 0x46
470xdc3	at vme0 addr 0xeeb0 irq 3 vect 0x47
471xd*	at xdc? drive ?
472
473## Xylogics 451 or 451 VME SMD disk controllers and disks, found
474## on sun4 systems.
475xyc0	at vme0 addr 0xee40 irq 3 vect 0x48
476xyc1	at vme0 addr 0xee48 irq 3 vect 0x49
477xy*	at xyc? drive ?
478
479
480## Floppy controller and drive found on SPARCstations.
481
482fdc0	at mainbus0				# sun4c controller
483fdc0	at obio0				# sun4m controller
484fd*	at fdc0					# the drive itself
485
486## PCMCIA IDE controllers
487#wdc*	at pcmcia?
488#atabus* at ata?
489#wd*	at atabus? drive ? flags 0x0000
490
491## A disk-like interface to files.  Can be used to create floppy, CD,
492## miniroot images, etc.
493
494pseudo-device	vnd
495#options 	VND_COMPRESSION		# compressed vnd(4)
496
497## Concatenated and striped disks; with this, you can create a software-based
498## disk array similar to a "RAID 0" setup.  See ccd(4).
499
500pseudo-device	ccd
501
502## Cryptographic disk devices;  See cgd(4)
503
504#pseudo-device	cgd
505
506## RAIDframe disk driver: software RAID driver.  See raid(4).
507
508pseudo-device	raid
509options 	RAID_AUTOCONFIG		# auto-configuration of RAID components
510# Options to enable various other RAIDframe RAID types.
511# options 	RF_INCLUDE_EVENODD=1
512# options 	RF_INCLUDE_RAID5_RS=1
513# options 	RF_INCLUDE_PARITYLOGGING=1
514# options 	RF_INCLUDE_CHAINDECLUSTER=1
515# options 	RF_INCLUDE_INTERDECLUSTER=1
516# options 	RF_INCLUDE_PARITY_DECLUSTERING=1
517# options 	RF_INCLUDE_PARITY_DECLUSTERING_DS=1
518
519
520## Memory disk device, used on boot floppies with compressed
521## kernel-plus-root-disk images.
522
523#pseudo-device	md
524
525
526#### Network interfaces
527
528## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
529## Three flavors of additional SBus ethernets are available.  One attaches
530## directly like the sun4c on-board, one uses the ledma device like the
531## sun4m on-board, and one uses the lebuffer device.
532
533le0		at obio0 addr 0xf9000000 level 6	# sun4/300
534le0		at sbus0 slot ? offset ?		# sun4c on-board
535ledma0		at sbus0 slot ? offset ?		# sun4m on-board
536le0		at ledma0				# sun4m on-board
537le*		at sbus? slot ? offset ?		# SBus
538ledma*		at sbus? slot ? offset ?		# SBus
539le*		at ledma?				# SBus
540lebuffer0	at sbus? slot ? offset ?		# SBus
541le0		at lebuffer?				# SBus
542lebuffer*	at sbus? slot ? offset ?		# SBus
543le*		at lebuffer?				# SBus
544
545
546## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board
547## or on a Multibus/VME card.
548ie0	at obio0 addr 0xf6000000 level 6		# sun4/200 on-board
549ie0	at obio0 addr 0x06000000 level 6		# sun4/100 on-board
550## VME: the first [addr,len] pair specifies the device registers;
551##	the second pair specifies the on-board memory buffer
552ie1	at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75
553ie2	at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76
554ie3	at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77
555ie4	at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c
556
557## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet
558## (qe, 10MBd) attached.
559qec*	at sbus? slot ? offset ?		# Quad Ethernet Controller
560be*	at qec?					# BigMac Ethernet (10/100MBd)
561qe*	at qec?					# Mace Ethernet (10MBd)
562
563## Happy Meal Ethernet
564hme*	at sbus? slot ? offset ?
565
566# midway ATM
567en0	at sbus? slot ? offset ?
568
569# PCMCIA ethernet devices
570#ep*	at pcmcia?
571#mbe*	at pcmcia?
572#ne*	at pcmcia?
573#sm*	at pcmcia?
574
575## PCMCIA wavelan card
576#wi*	at pcmcia? function ?		# Lucent WaveLan IEEE (802.11)
577
578# MII/PHY support
579exphy*	at mii? phy ?			# 3Com internal PHYs
580icsphy*	at mii? phy ?			# Integrated Circuit Systems ICS189x
581inphy*	at mii? phy ?			# Intel 82555 PHYs
582lxtphy*	at mii? phy ?			# Level One LXT-970 PHYs
583nsphy*	at mii? phy ?			# NS83840 PHYs
584qsphy*	at mii? phy ?			# Quality Semiconductor QS6612 PHYs
585sqphy*	at mii? phy ?			# Seeq 80220/80221/80223 PHYs
586tlphy*	at mii? phy ?			# ThunderLAN PHYs
587ukphy*	at mii? phy ?			# generic unknown PHYs
588
589## Loopback network interface; required
590pseudo-device	loop
591
592## SLIP and CSLIP interfaces, for IP over a serial line.
593pseudo-device	sl
594
595## PPP, the successor to SLIP.  See pppd(8).
596pseudo-device	ppp
597
598## PPP over Ethernet (RFC 2516)
599pseudo-device	pppoe
600
601## Starmode Radio IP, a special hardware network device.
602#pseudo-device	strip
603
604## Network "tunnel" device, allowing protocol stacks to run in the userland.
605## This is used by the third-party user-mode "ppp" program, and others.
606pseudo-device	tun
607pseudo-device	tap			# virtual Ethernet
608
609## Generic L3 over IP tunnel
610#pseudo-device	gre			# generic L3 over IP tunnel
611
612## Berkeley Packet Filter, required to run RARPD.  A generic C-language
613## interface that allows selective examining of incoming packets.
614pseudo-device	bpfilter
615
616#pseudo-device	carp			# Common Address Redundancy Protocol
617
618## IP Filter, used in firewall and NAT applications.  See ipnat(8) for
619## one example of the use of the IP Filter.
620pseudo-device	ipfilter
621
622## for IPv6
623pseudo-device	gif			# IPv[46] over IPv[46] tunnel (RFC1933)
624#pseudo-device	faith			# IPv[46] tcp relay translation i/f
625pseudo-device	stf			# 6to4 IPv6 over IPv4 encapsulation
626
627## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4).
628pseudo-device	vlan
629
630## Simple inter-network traffic bridging
631pseudo-device	bridge
632#options 	BRIDGE_IPF		# bridge uses IP/IPv6 pfil hooks too
633pseudo-device	agr			# IEEE 802.3ad link aggregation
634
635## accept filters
636pseudo-device   accf_data		# "dataready" accept filter
637pseudo-device   accf_http		# "httpready" accept filter
638
639#### Audio and video devices
640
641## /dev/audio support (`audioamd' plus `audio')
642##
643audioamd0	at mainbus0				# sun4c
644audioamd0	at obio0				# sun4m
645audioamd0	at sbus0 slot ? offset ?		# sun4m
646
647audiocs0	at sbus0 slot ? offset ?		# SUNW,CS4231
648
649#options 	DBRI_DEBUG	# noisy debug output from the dbri driver
650#options 	DBRI_BIG_BUFFER	# use bigger DMA buffers, for slow CPUs
651dbri*		at sbus? slot ? offset ?		# SUNW,DBRI[s3|e]
652
653audio*		at audiobus?
654
655## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
656## systems.  If your sun4 system has a cgfour installed in the P4 slot,
657## the P4 entries for "bwtwo" will attach to the overlay plane of the
658## "cgfour".
659
660bwtwo0		at sbus0 slot ? offset ?		# sun4c and sun4m
661bwtwo*		at sbus? slot ? offset ?		#
662bwtwo0		at obio0 addr 0xfd000000 level 4	# sun4/200
663bwtwo0		at obio0 addr 0xfb300000 level 4	# sun4/300 in P4 slot
664bwtwo0		at obio0 addr 0x0b300000 level 4	# sun4/100 in P4 slot
665
666## Sun "cgtwo" VME color framebuffer
667# XXX no wsdisplay support
668#cgtwo0		at vme0 addr 0x400000 irq ? vect 0xa8
669
670## Sun "cgthree" Sbus color framebuffer
671cgthree0	at sbus? slot ? offset ?
672cgthree*	at sbus? slot ? offset ?
673
674## Sun "cgfour" color framebuffer with overlay plane.  See above comment
675## regarding overlay plane.
676# XXX no wsdisplay support
677#cgfour0		at obio0 addr 0xfb300000 level 4	# sun4/300 P4
678#cgfour0		at obio0 addr 0x0b300000 level 4	# sun4/100 P4
679
680## Sun "cgsix" accelerated color framebuffer.
681cgsix0		at sbus? slot ? offset ?
682cgsix*		at sbus? slot ? offset ?
683cgsix0		at obio0 addr 0xfb000000 level 4	# sun4/300 P4
684cgsix0		at obio0 addr 0x0b000000 level 4	# sun4/100 P4
685
686## Sun "cgeight" 24-bit framebuffer
687# XXX no wsdisplay support
688#cgeight0 	at obio0 addr 0xfb300000 level 4	# sun4/300 P4
689#cgeight0	at obio0 addr 0x0b300000 level 4	# sun4/100 P4
690
691## Sun "tcx" accelerated color framebuffer.
692# there can be only one
693tcx0		at sbus? slot ? offset ?
694
695## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer
696## runs monochrome only for now
697cgtwelve*	at sbus? slot ? offset ?
698
699# Sun "cgfourteen" accelerated 24-bit framebuffer.
700cgfourteen*	at obio0			# sun4m
701
702# P9100-based display on Tadpole SPARCbook 3.
703pnozz0		at sbus? slot ? offset ?
704# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be
705# 'latched in' but at least my 3GX works happily without
706# Enable it by default since we don't know which hardware really needs it.
707options PNOZZ_USE_LATCH
708
709# Sun ZX/Leo 24-bit framebuffer
710zx*		at sbus? slot ? offset ?
711
712# Fujitsu AG-10e accelerated graphics 8/24-bit board
713agten*	at sbus? slot ? offset ?
714
715# generic framebuffer console
716genfb*	at sbus? slot ? offset ?
717
718# make sure wsdisplay0 is the console
719wsdisplay0	at wsemuldisplaydev? console 1
720wsdisplay*	at wsemuldisplaydev?
721
722#### Other device configuration
723
724# Tadpole microcontroller
725tctrl0 at obio0
726
727# Aurora Personality Chip (APC) on SPARCstation-4/5
728# Not enabled by default as it may hang some systems
729#apc*		at sbus? slot ? offset ?
730
731## Pseudo ttys, required for network logins and programs like screen.
732
733pseudo-device	pty			# pseudo-terminals
734
735## Random device, used to implement /dev/random (a source of random noise),
736## and generate randomness for some kernel formulae.
737
738
739# a pseudo device needed for Coda	# also needs CODA (above)
740pseudo-device	vcoda			# coda minicache <-> venus comm.
741
742pseudo-device	clockctl		# user control of clock subsystem
743pseudo-device	ksyms			# /dev/ksyms
744#pseudo-device	pf			# PF packet filter
745#pseudo-device	pflog			# PF log if
746pseudo-device	fss			# file system snapshot device
747pseudo-device	wsmux			# mouse and keyboard multiplexor
748pseudo-device	wsfont
749pseudo-device	putter			# for puffs and pud
750
751#options 	FILEASSOC		# fileassoc(9)
752
753# Veriexec
754#
755# a pseudo device needed for veriexec
756#pseudo-device	veriexec
757#
758# Uncomment the fingerprint methods below that are desired. Note that
759# removing fingerprint methods will have almost no impact on the kernel
760# code size.
761#
762#options VERIFIED_EXEC_FP_RMD160
763#options VERIFIED_EXEC_FP_SHA256
764#options VERIFIED_EXEC_FP_SHA384
765#options VERIFIED_EXEC_FP_SHA512
766#options VERIFIED_EXEC_FP_SHA1
767#options VERIFIED_EXEC_FP_MD5
768
769#options PAX_MPROTECT=0			# PaX mprotect(2) restrictions
770					# (for static binaries only for now)
771