1.. BSD LICENSE 2 Copyright(c) 2010-2016 Intel Corporation. All rights reserved. 3 All rights reserved. 4 5 Redistribution and use in source and binary forms, with or without 6 modification, are permitted provided that the following conditions 7 are met: 8 9 * Redistributions of source code must retain the above copyright 10 notice, this list of conditions and the following disclaimer. 11 * Redistributions in binary form must reproduce the above copyright 12 notice, this list of conditions and the following disclaimer in 13 the documentation and/or other materials provided with the 14 distribution. 15 * Neither the name of Intel Corporation nor the names of its 16 contributors may be used to endorse or promote products derived 17 from this software without specific prior written permission. 18 19 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 20 "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 21 LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 22 A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 23 OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 24 SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 25 LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 26 DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 27 THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 28 (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 29 OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 30 31.. _testpmd_runtime: 32 33Testpmd Runtime Functions 34========================= 35 36Where the testpmd application is started in interactive mode, (``-i|--interactive``), 37it displays a prompt that can be used to start and stop forwarding, 38configure the application, display statistics (including the extended NIC 39statistics aka xstats) , set the Flow Director and other tasks:: 40 41 testpmd> 42 43The testpmd prompt has some, limited, readline support. 44Common bash command-line functions such as ``Ctrl+a`` and ``Ctrl+e`` to go to the start and end of the prompt line are supported 45as well as access to the command history via the up-arrow. 46 47There is also support for tab completion. 48If you type a partial command and hit ``<TAB>`` you get a list of the available completions: 49 50.. code-block:: console 51 52 testpmd> show port <TAB> 53 54 info [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap X 55 info [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap all 56 stats [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap X 57 stats [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap all 58 ... 59 60 61.. note:: 62 63 Some examples in this document are too long to fit on one line are are shown wrapped at `"\\"` for display purposes:: 64 65 testpmd> set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \ 66 (pause_time) (send_xon) (port_id) 67 68In the real ``testpmd>`` prompt these commands should be on a single line. 69 70Help Functions 71-------------- 72 73The testpmd has on-line help for the functions that are available at runtime. 74These are divided into sections and can be accessed using help, help section or help all: 75 76.. code-block:: console 77 78 testpmd> help 79 80 help control : Start and stop forwarding. 81 help display : Displaying port, stats and config information. 82 help config : Configuration information. 83 help ports : Configuring ports. 84 help registers : Reading and setting port registers. 85 help filters : Filters configuration help. 86 help all : All of the above sections. 87 88 89Command File Functions 90---------------------- 91 92To facilitate loading large number of commands or to avoid cutting and pasting where not 93practical or possible testpmd supports alternative methods for executing commands. 94 95* If started with the ``--cmdline-file=FILENAME`` command line argument testpmd 96 will execute all CLI commands contained within the file immediately before 97 starting packet forwarding or entering interactive mode. 98 99.. code-block:: console 100 101 ./testpmd -n4 -r2 ... -- -i --cmdline-file=/home/ubuntu/flow-create-commands.txt 102 Interactive-mode selected 103 CLI commands to be read from /home/ubuntu/flow-create-commands.txt 104 Configuring Port 0 (socket 0) 105 Port 0: 7C:FE:90:CB:74:CE 106 Configuring Port 1 (socket 0) 107 Port 1: 7C:FE:90:CB:74:CA 108 Checking link statuses... 109 Port 0 Link Up - speed 10000 Mbps - full-duplex 110 Port 1 Link Up - speed 10000 Mbps - full-duplex 111 Done 112 Flow rule #0 created 113 Flow rule #1 created 114 ... 115 ... 116 Flow rule #498 created 117 Flow rule #499 created 118 Read all CLI commands from /home/ubuntu/flow-create-commands.txt 119 testpmd> 120 121 122* At run-time additional commands can be loaded in bulk by invoking the ``load FILENAME`` 123 command. 124 125.. code-block:: console 126 127 testpmd> load /home/ubuntu/flow-create-commands.txt 128 Flow rule #0 created 129 Flow rule #1 created 130 ... 131 ... 132 Flow rule #498 created 133 Flow rule #499 created 134 Read all CLI commands from /home/ubuntu/flow-create-commands.txt 135 testpmd> 136 137 138In all cases output from any included command will be displayed as standard output. 139Execution will continue until the end of the file is reached regardless of 140whether any errors occur. The end user must examine the output to determine if 141any failures occurred. 142 143 144Control Functions 145----------------- 146 147start 148~~~~~ 149 150Start packet forwarding with current configuration:: 151 152 testpmd> start 153 154start tx_first 155~~~~~~~~~~~~~~ 156 157Start packet forwarding with current configuration after sending specified number of bursts of packets:: 158 159 testpmd> start tx_first (""|burst_num) 160 161The default burst number is 1 when ``burst_num`` not presented. 162 163stop 164~~~~ 165 166Stop packet forwarding, and display accumulated statistics:: 167 168 testpmd> stop 169 170quit 171~~~~ 172 173Quit to prompt:: 174 175 testpmd> quit 176 177 178Display Functions 179----------------- 180 181The functions in the following sections are used to display information about the 182testpmd configuration or the NIC status. 183 184show port 185~~~~~~~~~ 186 187Display information for a given port or all ports:: 188 189 testpmd> show port (info|stats|xstats|fdir|stat_qmap|dcb_tc|cap) (port_id|all) 190 191The available information categories are: 192 193* ``info``: General port information such as MAC address. 194 195* ``stats``: RX/TX statistics. 196 197* ``xstats``: RX/TX extended NIC statistics. 198 199* ``fdir``: Flow Director information and statistics. 200 201* ``stat_qmap``: Queue statistics mapping. 202 203* ``dcb_tc``: DCB information such as TC mapping. 204 205* ``cap``: Supported offload capabilities. 206 207For example: 208 209.. code-block:: console 210 211 testpmd> show port info 0 212 213 ********************* Infos for port 0 ********************* 214 215 MAC address: XX:XX:XX:XX:XX:XX 216 Connect to socket: 0 217 memory allocation on the socket: 0 218 Link status: up 219 Link speed: 40000 Mbps 220 Link duplex: full-duplex 221 Promiscuous mode: enabled 222 Allmulticast mode: disabled 223 Maximum number of MAC addresses: 64 224 Maximum number of MAC addresses of hash filtering: 0 225 VLAN offload: 226 strip on 227 filter on 228 qinq(extend) off 229 Redirection table size: 512 230 Supported flow types: 231 ipv4-frag 232 ipv4-tcp 233 ipv4-udp 234 ipv4-sctp 235 ipv4-other 236 ipv6-frag 237 ipv6-tcp 238 ipv6-udp 239 ipv6-sctp 240 ipv6-other 241 l2_payload 242 port 243 vxlan 244 geneve 245 nvgre 246 247show port rss reta 248~~~~~~~~~~~~~~~~~~ 249 250Display the rss redirection table entry indicated by masks on port X:: 251 252 testpmd> show port (port_id) rss reta (size) (mask0, mask1...) 253 254size is used to indicate the hardware supported reta size 255 256show port rss-hash 257~~~~~~~~~~~~~~~~~~ 258 259Display the RSS hash functions and RSS hash key of a port:: 260 261 testpmd> show port (port_id) rss-hash ipv4|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp|ipv4-other|ipv6|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other|l2-payload|ipv6-ex|ipv6-tcp-ex|ipv6-udp-ex [key] 262 263clear port 264~~~~~~~~~~ 265 266Clear the port statistics for a given port or for all ports:: 267 268 testpmd> clear port (info|stats|xstats|fdir|stat_qmap) (port_id|all) 269 270For example:: 271 272 testpmd> clear port stats all 273 274show (rxq|txq) 275~~~~~~~~~~~~~~ 276 277Display information for a given port's RX/TX queue:: 278 279 testpmd> show (rxq|txq) info (port_id) (queue_id) 280 281show config 282~~~~~~~~~~~ 283 284Displays the configuration of the application. 285The configuration comes from the command-line, the runtime or the application defaults:: 286 287 testpmd> show config (rxtx|cores|fwd|txpkts) 288 289The available information categories are: 290 291* ``rxtx``: RX/TX configuration items. 292 293* ``cores``: List of forwarding cores. 294 295* ``fwd``: Packet forwarding configuration. 296 297* ``txpkts``: Packets to TX configuration. 298 299For example: 300 301.. code-block:: console 302 303 testpmd> show config rxtx 304 305 io packet forwarding - CRC stripping disabled - packets/burst=16 306 nb forwarding cores=2 - nb forwarding ports=1 307 RX queues=1 - RX desc=128 - RX free threshold=0 308 RX threshold registers: pthresh=8 hthresh=8 wthresh=4 309 TX queues=1 - TX desc=512 - TX free threshold=0 310 TX threshold registers: pthresh=36 hthresh=0 wthresh=0 311 TX RS bit threshold=0 - TXQ flags=0x0 312 313set fwd 314~~~~~~~ 315 316Set the packet forwarding mode:: 317 318 testpmd> set fwd (io|mac|macswap|flowgen| \ 319 rxonly|txonly|csum|icmpecho) (""|retry) 320 321``retry`` can be specified for forwarding engines except ``rx_only``. 322 323The available information categories are: 324 325* ``io``: Forwards packets "as-is" in I/O mode. 326 This is the fastest possible forwarding operation as it does not access packets data. 327 This is the default mode. 328 329* ``mac``: Changes the source and the destination Ethernet addresses of packets before forwarding them. 330 Default application behaviour is to set source Ethernet address to that of the transmitting interface, and destination 331 address to a dummy value (set during init). The user may specify a target destination Ethernet address via the 'eth-peer' or 332 'eth-peer-configfile' command-line options. It is not currently possible to specify a specific source Ethernet address. 333 334* ``macswap``: MAC swap forwarding mode. 335 Swaps the source and the destination Ethernet addresses of packets before forwarding them. 336 337* ``flowgen``: Multi-flow generation mode. 338 Originates a number of flows (with varying destination IP addresses), and terminate receive traffic. 339 340* ``rxonly``: Receives packets but doesn't transmit them. 341 342* ``txonly``: Generates and transmits packets without receiving any. 343 344* ``csum``: Changes the checksum field with hardware or software methods depending on the offload flags on the packet. 345 346* ``icmpecho``: Receives a burst of packets, lookup for IMCP echo requests and, if any, send back ICMP echo replies. 347 348* ``ieee1588``: Demonstrate L2 IEEE1588 V2 PTP timestamping for RX and TX. Requires ``CONFIG_RTE_LIBRTE_IEEE1588=y``. 349 350Note: TX timestamping is only available in the "Full Featured" TX path. To force ``testpmd`` into this mode set ``--txqflags=0``. 351 352Example:: 353 354 testpmd> set fwd rxonly 355 356 Set rxonly packet forwarding mode 357 358 359read rxd 360~~~~~~~~ 361 362Display an RX descriptor for a port RX queue:: 363 364 testpmd> read rxd (port_id) (queue_id) (rxd_id) 365 366For example:: 367 368 testpmd> read rxd 0 0 4 369 0x0000000B - 0x001D0180 / 0x0000000B - 0x001D0180 370 371read txd 372~~~~~~~~ 373 374Display a TX descriptor for a port TX queue:: 375 376 testpmd> read txd (port_id) (queue_id) (txd_id) 377 378For example:: 379 380 testpmd> read txd 0 0 4 381 0x00000001 - 0x24C3C440 / 0x000F0000 - 0x2330003C 382 383ddp get list 384~~~~~~~~~~~~ 385 386Get loaded dynamic device personalization (DDP) package info list:: 387 388 testpmd> ddp get list (port_id) 389 390ddp get info 391~~~~~~~~~~~~ 392 393Display information about dynamic device personalization (DDP) profile:: 394 395 testpmd> ddp get info (profile_patch) 396 397show vf stats 398~~~~~~~~~~~~~ 399 400Display VF statistics:: 401 402 testpmd> show vf stats (port_id) (vf_id) 403 404clear vf stats 405~~~~~~~~~~~~~~ 406 407Reset VF statistics:: 408 409 testpmd> clear vf stats (port_id) (vf_id) 410 411Configuration Functions 412----------------------- 413 414The testpmd application can be configured from the runtime as well as from the command-line. 415 416This section details the available configuration functions that are available. 417 418.. note:: 419 420 Configuration changes only become active when forwarding is started/restarted. 421 422set default 423~~~~~~~~~~~ 424 425Reset forwarding to the default configuration:: 426 427 testpmd> set default 428 429set verbose 430~~~~~~~~~~~ 431 432Set the debug verbosity level:: 433 434 testpmd> set verbose (level) 435 436Currently the only available levels are 0 (silent except for error) and 1 (fully verbose). 437 438set nbport 439~~~~~~~~~~ 440 441Set the number of ports used by the application: 442 443set nbport (num) 444 445This is equivalent to the ``--nb-ports`` command-line option. 446 447set nbcore 448~~~~~~~~~~ 449 450Set the number of cores used by the application:: 451 452 testpmd> set nbcore (num) 453 454This is equivalent to the ``--nb-cores`` command-line option. 455 456.. note:: 457 458 The number of cores used must not be greater than number of ports used multiplied by the number of queues per port. 459 460set coremask 461~~~~~~~~~~~~ 462 463Set the forwarding cores hexadecimal mask:: 464 465 testpmd> set coremask (mask) 466 467This is equivalent to the ``--coremask`` command-line option. 468 469.. note:: 470 471 The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding. 472 473set portmask 474~~~~~~~~~~~~ 475 476Set the forwarding ports hexadecimal mask:: 477 478 testpmd> set portmask (mask) 479 480This is equivalent to the ``--portmask`` command-line option. 481 482set burst 483~~~~~~~~~ 484 485Set number of packets per burst:: 486 487 testpmd> set burst (num) 488 489This is equivalent to the ``--burst command-line`` option. 490 491When retry is enabled, the transmit delay time and number of retries can also be set:: 492 493 testpmd> set burst tx delay (microseconds) retry (num) 494 495set txpkts 496~~~~~~~~~~ 497 498Set the length of each segment of the TX-ONLY packets or length of packet for FLOWGEN mode:: 499 500 testpmd> set txpkts (x[,y]*) 501 502Where x[,y]* represents a CSV list of values, without white space. 503 504set txsplit 505~~~~~~~~~~~ 506 507Set the split policy for the TX packets, applicable for TX-ONLY and CSUM forwarding modes:: 508 509 testpmd> set txsplit (off|on|rand) 510 511Where: 512 513* ``off`` disable packet copy & split for CSUM mode. 514 515* ``on`` split outgoing packet into multiple segments. Size of each segment 516 and number of segments per packet is determined by ``set txpkts`` command 517 (see above). 518 519* ``rand`` same as 'on', but number of segments per each packet is a random value between 1 and total number of segments. 520 521set corelist 522~~~~~~~~~~~~ 523 524Set the list of forwarding cores:: 525 526 testpmd> set corelist (x[,y]*) 527 528For example, to change the forwarding cores: 529 530.. code-block:: console 531 532 testpmd> set corelist 3,1 533 testpmd> show config fwd 534 535 io packet forwarding - ports=2 - cores=2 - streams=2 - NUMA support disabled 536 Logical Core 3 (socket 0) forwards packets on 1 streams: 537 RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 538 Logical Core 1 (socket 0) forwards packets on 1 streams: 539 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 540 541.. note:: 542 543 The cores are used in the same order as specified on the command line. 544 545set portlist 546~~~~~~~~~~~~ 547 548Set the list of forwarding ports:: 549 550 testpmd> set portlist (x[,y]*) 551 552For example, to change the port forwarding: 553 554.. code-block:: console 555 556 testpmd> set portlist 0,2,1,3 557 testpmd> show config fwd 558 559 io packet forwarding - ports=4 - cores=1 - streams=4 560 Logical Core 3 (socket 0) forwards packets on 4 streams: 561 RX P=0/Q=0 (socket 0) -> TX P=2/Q=0 (socket 0) peer=02:00:00:00:00:01 562 RX P=2/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 563 RX P=1/Q=0 (socket 0) -> TX P=3/Q=0 (socket 0) peer=02:00:00:00:00:03 564 RX P=3/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:02 565 566set tx loopback 567~~~~~~~~~~~~~~~ 568 569Enable/disable tx loopback:: 570 571 testpmd> set tx loopback (port_id) (on|off) 572 573set drop enable 574~~~~~~~~~~~~~~~ 575 576set drop enable bit for all queues:: 577 578 testpmd> set all queues drop (port_id) (on|off) 579 580set split drop enable (for VF) 581~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 582 583set split drop enable bit for VF from PF:: 584 585 testpmd> set vf split drop (port_id) (vf_id) (on|off) 586 587set mac antispoof (for VF) 588~~~~~~~~~~~~~~~~~~~~~~~~~~ 589 590Set mac antispoof for a VF from the PF:: 591 592 testpmd> set vf mac antispoof (port_id) (vf_id) (on|off) 593 594set macsec offload 595~~~~~~~~~~~~~~~~~~ 596 597Enable/disable MACsec offload:: 598 599 testpmd> set macsec offload (port_id) on encrypt (on|off) replay-protect (on|off) 600 testpmd> set macsec offload (port_id) off 601 602set macsec sc 603~~~~~~~~~~~~~ 604 605Configure MACsec secure connection (SC):: 606 607 testpmd> set macsec sc (tx|rx) (port_id) (mac) (pi) 608 609.. note:: 610 611 The pi argument is ignored for tx. 612 Check the NIC Datasheet for hardware limits. 613 614set macsec sa 615~~~~~~~~~~~~~ 616 617Configure MACsec secure association (SA):: 618 619 testpmd> set macsec sa (tx|rx) (port_id) (idx) (an) (pn) (key) 620 621.. note:: 622 623 The IDX value must be 0 or 1. 624 Check the NIC Datasheet for hardware limits. 625 626set broadcast mode (for VF) 627~~~~~~~~~~~~~~~~~~~~~~~~~~~ 628 629Set broadcast mode for a VF from the PF:: 630 631 testpmd> set vf broadcast (port_id) (vf_id) (on|off) 632 633vlan set strip 634~~~~~~~~~~~~~~ 635 636Set the VLAN strip on a port:: 637 638 testpmd> vlan set strip (on|off) (port_id) 639 640vlan set stripq 641~~~~~~~~~~~~~~~ 642 643Set the VLAN strip for a queue on a port:: 644 645 testpmd> vlan set stripq (on|off) (port_id,queue_id) 646 647vlan set stripq (for VF) 648~~~~~~~~~~~~~~~~~~~~~~~~ 649 650Set VLAN strip for all queues in a pool for a VF from the PF:: 651 652 testpmd> set vf vlan stripq (port_id) (vf_id) (on|off) 653 654vlan set insert (for VF) 655~~~~~~~~~~~~~~~~~~~~~~~~ 656 657Set VLAN insert for a VF from the PF:: 658 659 testpmd> set vf vlan insert (port_id) (vf_id) (vlan_id) 660 661vlan set tag (for VF) 662~~~~~~~~~~~~~~~~~~~~~ 663 664Set VLAN tag for a VF from the PF:: 665 666 testpmd> set vf vlan tag (port_id) (vf_id) (on|off) 667 668vlan set antispoof (for VF) 669~~~~~~~~~~~~~~~~~~~~~~~~~~~ 670 671Set VLAN antispoof for a VF from the PF:: 672 673 testpmd> set vf vlan antispoof (port_id) (vf_id) (on|off) 674 675vlan set filter 676~~~~~~~~~~~~~~~ 677 678Set the VLAN filter on a port:: 679 680 testpmd> vlan set filter (on|off) (port_id) 681 682vlan set qinq 683~~~~~~~~~~~~~ 684 685Set the VLAN QinQ (extended queue in queue) on for a port:: 686 687 testpmd> vlan set qinq (on|off) (port_id) 688 689vlan set tpid 690~~~~~~~~~~~~~ 691 692Set the inner or outer VLAN TPID for packet filtering on a port:: 693 694 testpmd> vlan set (inner|outer) tpid (value) (port_id) 695 696.. note:: 697 698 TPID value must be a 16-bit number (value <= 65536). 699 700rx_vlan add 701~~~~~~~~~~~ 702 703Add a VLAN ID, or all identifiers, to the set of VLAN identifiers filtered by port ID:: 704 705 testpmd> rx_vlan add (vlan_id|all) (port_id) 706 707.. note:: 708 709 VLAN filter must be set on that port. VLAN ID < 4096. 710 Depending on the NIC used, number of vlan_ids may be limited to the maximum entries 711 in VFTA table. This is important if enabling all vlan_ids. 712 713rx_vlan rm 714~~~~~~~~~~ 715 716Remove a VLAN ID, or all identifiers, from the set of VLAN identifiers filtered by port ID:: 717 718 testpmd> rx_vlan rm (vlan_id|all) (port_id) 719 720rx_vlan add (for VF) 721~~~~~~~~~~~~~~~~~~~~ 722 723Add a VLAN ID, to the set of VLAN identifiers filtered for VF(s) for port ID:: 724 725 testpmd> rx_vlan add (vlan_id) port (port_id) vf (vf_mask) 726 727rx_vlan rm (for VF) 728~~~~~~~~~~~~~~~~~~~ 729 730Remove a VLAN ID, from the set of VLAN identifiers filtered for VF(s) for port ID:: 731 732 testpmd> rx_vlan rm (vlan_id) port (port_id) vf (vf_mask) 733 734tunnel_filter add 735~~~~~~~~~~~~~~~~~ 736 737Add a tunnel filter on a port:: 738 739 testpmd> tunnel_filter add (port_id) (outer_mac) (inner_mac) (ip_addr) \ 740 (inner_vlan) (vxlan|nvgre|ipingre) (imac-ivlan|imac-ivlan-tenid|\ 741 imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id) 742 743The available information categories are: 744 745* ``vxlan``: Set tunnel type as VXLAN. 746 747* ``nvgre``: Set tunnel type as NVGRE. 748 749* ``ipingre``: Set tunnel type as IP-in-GRE. 750 751* ``imac-ivlan``: Set filter type as Inner MAC and VLAN. 752 753* ``imac-ivlan-tenid``: Set filter type as Inner MAC, VLAN and tenant ID. 754 755* ``imac-tenid``: Set filter type as Inner MAC and tenant ID. 756 757* ``imac``: Set filter type as Inner MAC. 758 759* ``omac-imac-tenid``: Set filter type as Outer MAC, Inner MAC and tenant ID. 760 761* ``oip``: Set filter type as Outer IP. 762 763* ``iip``: Set filter type as Inner IP. 764 765Example:: 766 767 testpmd> tunnel_filter add 0 68:05:CA:28:09:82 00:00:00:00:00:00 \ 768 192.168.2.2 0 ipingre oip 1 1 769 770 Set an IP-in-GRE tunnel on port 0, and the filter type is Outer IP. 771 772tunnel_filter remove 773~~~~~~~~~~~~~~~~~~~~ 774 775Remove a tunnel filter on a port:: 776 777 testpmd> tunnel_filter rm (port_id) (outer_mac) (inner_mac) (ip_addr) \ 778 (inner_vlan) (vxlan|nvgre|ipingre) (imac-ivlan|imac-ivlan-tenid|\ 779 imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id) 780 781rx_vxlan_port add 782~~~~~~~~~~~~~~~~~ 783 784Add an UDP port for VXLAN packet filter on a port:: 785 786 testpmd> rx_vxlan_port add (udp_port) (port_id) 787 788rx_vxlan_port remove 789~~~~~~~~~~~~~~~~~~~~ 790 791Remove an UDP port for VXLAN packet filter on a port:: 792 793 testpmd> rx_vxlan_port rm (udp_port) (port_id) 794 795tx_vlan set 796~~~~~~~~~~~ 797 798Set hardware insertion of VLAN IDs in packets sent on a port:: 799 800 testpmd> tx_vlan set (port_id) vlan_id[, vlan_id_outer] 801 802For example, set a single VLAN ID (5) insertion on port 0:: 803 804 tx_vlan set 0 5 805 806Or, set double VLAN ID (inner: 2, outer: 3) insertion on port 1:: 807 808 tx_vlan set 1 2 3 809 810 811tx_vlan set pvid 812~~~~~~~~~~~~~~~~ 813 814Set port based hardware insertion of VLAN ID in packets sent on a port:: 815 816 testpmd> tx_vlan set pvid (port_id) (vlan_id) (on|off) 817 818tx_vlan reset 819~~~~~~~~~~~~~ 820 821Disable hardware insertion of a VLAN header in packets sent on a port:: 822 823 testpmd> tx_vlan reset (port_id) 824 825csum set 826~~~~~~~~ 827 828Select hardware or software calculation of the checksum when 829transmitting a packet using the ``csum`` forwarding engine:: 830 831 testpmd> csum set (ip|udp|tcp|sctp|outer-ip) (hw|sw) (port_id) 832 833Where: 834 835* ``ip|udp|tcp|sctp`` always relate to the inner layer. 836 837* ``outer-ip`` relates to the outer IP layer (only for IPv4) in the case where the packet is recognized 838 as a tunnel packet by the forwarding engine (vxlan, gre and ipip are 839 supported). See also the ``csum parse-tunnel`` command. 840 841.. note:: 842 843 Check the NIC Datasheet for hardware limits. 844 845csum parse-tunnel 846~~~~~~~~~~~~~~~~~ 847 848Define how tunneled packets should be handled by the csum forward 849engine:: 850 851 testpmd> csum parse-tunnel (on|off) (tx_port_id) 852 853If enabled, the csum forward engine will try to recognize supported 854tunnel headers (vxlan, gre, ipip). 855 856If disabled, treat tunnel packets as non-tunneled packets (a inner 857header is handled as a packet payload). 858 859.. note:: 860 861 The port argument is the TX port like in the ``csum set`` command. 862 863Example: 864 865Consider a packet in packet like the following:: 866 867 eth_out/ipv4_out/udp_out/vxlan/eth_in/ipv4_in/tcp_in 868 869* If parse-tunnel is enabled, the ``ip|udp|tcp|sctp`` parameters of ``csum set`` 870 command relate to the inner headers (here ``ipv4_in`` and ``tcp_in``), and the 871 ``outer-ip parameter`` relates to the outer headers (here ``ipv4_out``). 872 873* If parse-tunnel is disabled, the ``ip|udp|tcp|sctp`` parameters of ``csum set`` 874 command relate to the outer headers, here ``ipv4_out`` and ``udp_out``. 875 876csum show 877~~~~~~~~~ 878 879Display tx checksum offload configuration:: 880 881 testpmd> csum show (port_id) 882 883tso set 884~~~~~~~ 885 886Enable TCP Segmentation Offload (TSO) in the ``csum`` forwarding engine:: 887 888 testpmd> tso set (segsize) (port_id) 889 890.. note:: 891 892 Check the NIC datasheet for hardware limits. 893 894tso show 895~~~~~~~~ 896 897Display the status of TCP Segmentation Offload:: 898 899 testpmd> tso show (port_id) 900 901gro 902~~~ 903 904Enable or disable GRO in ``csum`` forwarding engine:: 905 906 testpmd> gro (on|off) (port_id) 907 908If enabled, the csum forwarding engine will perform GRO on the TCP/IPv4 909packets received from the given port. 910 911If disabled, packets received from the given port won't be performed 912GRO. By default, GRO is disabled for all ports. 913 914.. note:: 915 916 When enable GRO for a port, TCP/IPv4 packets received from the port 917 will be performed GRO. After GRO, the merged packets are multi-segments. 918 But csum forwarding engine doesn't support to calculate TCP checksum 919 for multi-segment packets in SW. So please select TCP HW checksum 920 calculation for the port which GROed packets are transmitted to. 921 922gro set 923~~~~~~~ 924 925Set max flow number and max packet number per-flow for GRO:: 926 927 testpmd> gro set (max_flow_num) (max_item_num_per_flow) (port_id) 928 929The product of ``max_flow_num`` and ``max_item_num_per_flow`` is the max 930number of packets a GRO table can store. 931 932If current packet number is greater than or equal to the max value, GRO 933will stop processing incoming packets. 934 935mac_addr add 936~~~~~~~~~~~~ 937 938Add an alternative MAC address to a port:: 939 940 testpmd> mac_addr add (port_id) (XX:XX:XX:XX:XX:XX) 941 942mac_addr remove 943~~~~~~~~~~~~~~~ 944 945Remove a MAC address from a port:: 946 947 testpmd> mac_addr remove (port_id) (XX:XX:XX:XX:XX:XX) 948 949mac_addr add (for VF) 950~~~~~~~~~~~~~~~~~~~~~ 951 952Add an alternative MAC address for a VF to a port:: 953 954 testpmd> mac_add add port (port_id) vf (vf_id) (XX:XX:XX:XX:XX:XX) 955 956mac_addr set 957~~~~~~~~~~~~ 958 959Set the default MAC address for a port:: 960 961 testpmd> mac_addr set (port_id) (XX:XX:XX:XX:XX:XX) 962 963mac_addr set (for VF) 964~~~~~~~~~~~~~~~~~~~~~ 965 966Set the MAC address for a VF from the PF:: 967 968 testpmd> set vf mac addr (port_id) (vf_id) (XX:XX:XX:XX:XX:XX) 969 970set port-uta 971~~~~~~~~~~~~ 972 973Set the unicast hash filter(s) on/off for a port:: 974 975 testpmd> set port (port_id) uta (XX:XX:XX:XX:XX:XX|all) (on|off) 976 977set promisc 978~~~~~~~~~~~ 979 980Set the promiscuous mode on for a port or for all ports. 981In promiscuous mode packets are not dropped if they aren't for the specified MAC address:: 982 983 testpmd> set promisc (port_id|all) (on|off) 984 985set allmulti 986~~~~~~~~~~~~ 987 988Set the allmulti mode for a port or for all ports:: 989 990 testpmd> set allmulti (port_id|all) (on|off) 991 992Same as the ifconfig (8) option. Controls how multicast packets are handled. 993 994set promisc (for VF) 995~~~~~~~~~~~~~~~~~~~~ 996 997Set the unicast promiscuous mode for a VF from PF. 998It's supported by Intel i40e NICs now. 999In promiscuous mode packets are not dropped if they aren't for the specified MAC address:: 1000 1001 testpmd> set vf promisc (port_id) (vf_id) (on|off) 1002 1003set allmulticast (for VF) 1004~~~~~~~~~~~~~~~~~~~~~~~~~ 1005 1006Set the multicast promiscuous mode for a VF from PF. 1007It's supported by Intel i40e NICs now. 1008In promiscuous mode packets are not dropped if they aren't for the specified MAC address:: 1009 1010 testpmd> set vf allmulti (port_id) (vf_id) (on|off) 1011 1012set tx max bandwidth (for VF) 1013~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1014 1015Set TX max absolute bandwidth (Mbps) for a VF from PF:: 1016 1017 testpmd> set vf tx max-bandwidth (port_id) (vf_id) (max_bandwidth) 1018 1019set tc tx min bandwidth (for VF) 1020~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1021 1022Set all TCs' TX min relative bandwidth (%) for a VF from PF:: 1023 1024 testpmd> set vf tc tx min-bandwidth (port_id) (vf_id) (bw1, bw2, ...) 1025 1026set tc tx max bandwidth (for VF) 1027~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1028 1029Set a TC's TX max absolute bandwidth (Mbps) for a VF from PF:: 1030 1031 testpmd> set vf tc tx max-bandwidth (port_id) (vf_id) (tc_no) (max_bandwidth) 1032 1033set tc strict link priority mode 1034~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1035 1036Set some TCs' strict link priority mode on a physical port:: 1037 1038 testpmd> set tx strict-link-priority (port_id) (tc_bitmap) 1039 1040set tc tx min bandwidth 1041~~~~~~~~~~~~~~~~~~~~~~~ 1042 1043Set all TCs' TX min relative bandwidth (%) globally for all PF and VFs:: 1044 1045 testpmd> set tc tx min-bandwidth (port_id) (bw1, bw2, ...) 1046 1047set flow_ctrl rx 1048~~~~~~~~~~~~~~~~ 1049 1050Set the link flow control parameter on a port:: 1051 1052 testpmd> set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \ 1053 (pause_time) (send_xon) mac_ctrl_frame_fwd (on|off) \ 1054 autoneg (on|off) (port_id) 1055 1056Where: 1057 1058* ``high_water`` (integer): High threshold value to trigger XOFF. 1059 1060* ``low_water`` (integer): Low threshold value to trigger XON. 1061 1062* ``pause_time`` (integer): Pause quota in the Pause frame. 1063 1064* ``send_xon`` (0/1): Send XON frame. 1065 1066* ``mac_ctrl_frame_fwd``: Enable receiving MAC control frames. 1067 1068* ``autoneg``: Change the auto-negotiation parameter. 1069 1070set pfc_ctrl rx 1071~~~~~~~~~~~~~~~ 1072 1073Set the priority flow control parameter on a port:: 1074 1075 testpmd> set pfc_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \ 1076 (pause_time) (priority) (port_id) 1077 1078Where: 1079 1080* ``high_water`` (integer): High threshold value. 1081 1082* ``low_water`` (integer): Low threshold value. 1083 1084* ``pause_time`` (integer): Pause quota in the Pause frame. 1085 1086* ``priority`` (0-7): VLAN User Priority. 1087 1088set stat_qmap 1089~~~~~~~~~~~~~ 1090 1091Set statistics mapping (qmapping 0..15) for RX/TX queue on port:: 1092 1093 testpmd> set stat_qmap (tx|rx) (port_id) (queue_id) (qmapping) 1094 1095For example, to set rx queue 2 on port 0 to mapping 5:: 1096 1097 testpmd>set stat_qmap rx 0 2 5 1098 1099set port - rx/tx (for VF) 1100~~~~~~~~~~~~~~~~~~~~~~~~~ 1101 1102Set VF receive/transmit from a port:: 1103 1104 testpmd> set port (port_id) vf (vf_id) (rx|tx) (on|off) 1105 1106set port - mac address filter (for VF) 1107~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1108 1109Add/Remove unicast or multicast MAC addr filter for a VF:: 1110 1111 testpmd> set port (port_id) vf (vf_id) (mac_addr) \ 1112 (exact-mac|exact-mac-vlan|hashmac|hashmac-vlan) (on|off) 1113 1114set port - rx mode(for VF) 1115~~~~~~~~~~~~~~~~~~~~~~~~~~ 1116 1117Set the VF receive mode of a port:: 1118 1119 testpmd> set port (port_id) vf (vf_id) \ 1120 rxmode (AUPE|ROPE|BAM|MPE) (on|off) 1121 1122The available receive modes are: 1123 1124* ``AUPE``: Accepts untagged VLAN. 1125 1126* ``ROPE``: Accepts unicast hash. 1127 1128* ``BAM``: Accepts broadcast packets. 1129 1130* ``MPE``: Accepts all multicast packets. 1131 1132set port - tx_rate (for Queue) 1133~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1134 1135Set TX rate limitation for a queue on a port:: 1136 1137 testpmd> set port (port_id) queue (queue_id) rate (rate_value) 1138 1139set port - tx_rate (for VF) 1140~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1141 1142Set TX rate limitation for queues in VF on a port:: 1143 1144 testpmd> set port (port_id) vf (vf_id) rate (rate_value) queue_mask (queue_mask) 1145 1146set port - mirror rule 1147~~~~~~~~~~~~~~~~~~~~~~ 1148 1149Set pool or vlan type mirror rule for a port:: 1150 1151 testpmd> set port (port_id) mirror-rule (rule_id) \ 1152 (pool-mirror-up|pool-mirror-down|vlan-mirror) \ 1153 (poolmask|vlanid[,vlanid]*) dst-pool (pool_id) (on|off) 1154 1155Set link mirror rule for a port:: 1156 1157 testpmd> set port (port_id) mirror-rule (rule_id) \ 1158 (uplink-mirror|downlink-mirror) dst-pool (pool_id) (on|off) 1159 1160For example to enable mirror traffic with vlan 0,1 to pool 0:: 1161 1162 set port 0 mirror-rule 0 vlan-mirror 0,1 dst-pool 0 on 1163 1164reset port - mirror rule 1165~~~~~~~~~~~~~~~~~~~~~~~~ 1166 1167Reset a mirror rule for a port:: 1168 1169 testpmd> reset port (port_id) mirror-rule (rule_id) 1170 1171set flush_rx 1172~~~~~~~~~~~~ 1173 1174Set the flush on RX streams before forwarding. 1175The default is flush ``on``. 1176Mainly used with PCAP drivers to turn off the default behavior of flushing the first 512 packets on RX streams:: 1177 1178 testpmd> set flush_rx off 1179 1180set bypass mode 1181~~~~~~~~~~~~~~~ 1182 1183Set the bypass mode for the lowest port on bypass enabled NIC:: 1184 1185 testpmd> set bypass mode (normal|bypass|isolate) (port_id) 1186 1187set bypass event 1188~~~~~~~~~~~~~~~~ 1189 1190Set the event required to initiate specified bypass mode for the lowest port on a bypass enabled:: 1191 1192 testpmd> set bypass event (timeout|os_on|os_off|power_on|power_off) \ 1193 mode (normal|bypass|isolate) (port_id) 1194 1195Where: 1196 1197* ``timeout``: Enable bypass after watchdog timeout. 1198 1199* ``os_on``: Enable bypass when OS/board is powered on. 1200 1201* ``os_off``: Enable bypass when OS/board is powered off. 1202 1203* ``power_on``: Enable bypass when power supply is turned on. 1204 1205* ``power_off``: Enable bypass when power supply is turned off. 1206 1207 1208set bypass timeout 1209~~~~~~~~~~~~~~~~~~ 1210 1211Set the bypass watchdog timeout to ``n`` seconds where 0 = instant:: 1212 1213 testpmd> set bypass timeout (0|1.5|2|3|4|8|16|32) 1214 1215show bypass config 1216~~~~~~~~~~~~~~~~~~ 1217 1218Show the bypass configuration for a bypass enabled NIC using the lowest port on the NIC:: 1219 1220 testpmd> show bypass config (port_id) 1221 1222set link up 1223~~~~~~~~~~~ 1224 1225Set link up for a port:: 1226 1227 testpmd> set link-up port (port id) 1228 1229set link down 1230~~~~~~~~~~~~~ 1231 1232Set link down for a port:: 1233 1234 testpmd> set link-down port (port id) 1235 1236E-tag set 1237~~~~~~~~~ 1238 1239Enable E-tag insertion for a VF on a port:: 1240 1241 testpmd> E-tag set insertion on port-tag-id (value) port (port_id) vf (vf_id) 1242 1243Disable E-tag insertion for a VF on a port:: 1244 1245 testpmd> E-tag set insertion off port (port_id) vf (vf_id) 1246 1247Enable/disable E-tag stripping on a port:: 1248 1249 testpmd> E-tag set stripping (on|off) port (port_id) 1250 1251Enable/disable E-tag based forwarding on a port:: 1252 1253 testpmd> E-tag set forwarding (on|off) port (port_id) 1254 1255Add an E-tag forwarding filter on a port:: 1256 1257 testpmd> E-tag set filter add e-tag-id (value) dst-pool (pool_id) port (port_id) 1258 1259Delete an E-tag forwarding filter on a port:: 1260 testpmd> E-tag set filter del e-tag-id (value) port (port_id) 1261 1262ddp add 1263~~~~~~~ 1264 1265Load a dynamic device personalization (DDP) package:: 1266 1267 testpmd> ddp add (port_id) (package_path[,output_path]) 1268 1269ddp del 1270~~~~~~~ 1271 1272Delete a dynamic device personalization package:: 1273 1274 testpmd> ddp del (port_id) (package_path) 1275 1276ptype mapping 1277~~~~~~~~~~~~~ 1278 1279List all items from the ptype mapping table:: 1280 1281 testpmd> ptype mapping get (port_id) (valid_only) 1282 1283Where: 1284 1285* ``valid_only``: A flag indicates if only list valid items(=1) or all itemss(=0). 1286 1287Replace a specific or a group of software defined ptype with a new one:: 1288 1289 testpmd> ptype mapping replace (port_id) (target) (mask) (pkt_type) 1290 1291where: 1292 1293* ``target``: A specific software ptype or a mask to represent a group of software ptypes. 1294 1295* ``mask``: A flag indicate if "target" is a specific software ptype(=0) or a ptype mask(=1). 1296 1297* ``pkt_type``: The new software ptype to replace the old ones. 1298 1299Update hardware defined ptype to software defined packet type mapping table:: 1300 1301 testpmd> ptype mapping update (port_id) (hw_ptype) (sw_ptype) 1302 1303where: 1304 1305* ``hw_ptype``: hardware ptype as the index of the ptype mapping table. 1306 1307* ``sw_ptype``: software ptype as the value of the ptype mapping table. 1308 1309Reset ptype mapping table:: 1310 1311 testpmd> ptype mapping reset (port_id) 1312 1313Port Functions 1314-------------- 1315 1316The following sections show functions for configuring ports. 1317 1318.. note:: 1319 1320 Port configuration changes only become active when forwarding is started/restarted. 1321 1322port attach 1323~~~~~~~~~~~ 1324 1325Attach a port specified by pci address or virtual device args:: 1326 1327 testpmd> port attach (identifier) 1328 1329To attach a new pci device, the device should be recognized by kernel first. 1330Then it should be moved under DPDK management. 1331Finally the port can be attached to testpmd. 1332 1333For example, to move a pci device using ixgbe under DPDK management: 1334 1335.. code-block:: console 1336 1337 # Check the status of the available devices. 1338 ./usertools/dpdk-devbind.py --status 1339 1340 Network devices using DPDK-compatible driver 1341 ============================================ 1342 <none> 1343 1344 Network devices using kernel driver 1345 =================================== 1346 0000:0a:00.0 '82599ES 10-Gigabit' if=eth2 drv=ixgbe unused= 1347 1348 1349 # Bind the device to igb_uio. 1350 sudo ./usertools/dpdk-devbind.py -b igb_uio 0000:0a:00.0 1351 1352 1353 # Recheck the status of the devices. 1354 ./usertools/dpdk-devbind.py --status 1355 Network devices using DPDK-compatible driver 1356 ============================================ 1357 0000:0a:00.0 '82599ES 10-Gigabit' drv=igb_uio unused= 1358 1359To attach a port created by virtual device, above steps are not needed. 1360 1361For example, to attach a port whose pci address is 0000:0a:00.0. 1362 1363.. code-block:: console 1364 1365 testpmd> port attach 0000:0a:00.0 1366 Attaching a new port... 1367 EAL: PCI device 0000:0a:00.0 on NUMA socket -1 1368 EAL: probe driver: 8086:10fb rte_ixgbe_pmd 1369 EAL: PCI memory mapped at 0x7f83bfa00000 1370 EAL: PCI memory mapped at 0x7f83bfa80000 1371 PMD: eth_ixgbe_dev_init(): MAC: 2, PHY: 18, SFP+: 5 1372 PMD: eth_ixgbe_dev_init(): port 0 vendorID=0x8086 deviceID=0x10fb 1373 Port 0 is attached. Now total ports is 1 1374 Done 1375 1376For example, to attach a port created by pcap PMD. 1377 1378.. code-block:: console 1379 1380 testpmd> port attach net_pcap0 1381 Attaching a new port... 1382 PMD: Initializing pmd_pcap for net_pcap0 1383 PMD: Creating pcap-backed ethdev on numa socket 0 1384 Port 0 is attached. Now total ports is 1 1385 Done 1386 1387In this case, identifier is ``net_pcap0``. 1388This identifier format is the same as ``--vdev`` format of DPDK applications. 1389 1390For example, to re-attach a bonded port which has been previously detached, 1391the mode and slave parameters must be given. 1392 1393.. code-block:: console 1394 1395 testpmd> port attach net_bond_0,mode=0,slave=1 1396 Attaching a new port... 1397 EAL: Initializing pmd_bond for net_bond_0 1398 EAL: Create bonded device net_bond_0 on port 0 in mode 0 on socket 0. 1399 Port 0 is attached. Now total ports is 1 1400 Done 1401 1402 1403port detach 1404~~~~~~~~~~~ 1405 1406Detach a specific port:: 1407 1408 testpmd> port detach (port_id) 1409 1410Before detaching a port, the port should be stopped and closed. 1411 1412For example, to detach a pci device port 0. 1413 1414.. code-block:: console 1415 1416 testpmd> port stop 0 1417 Stopping ports... 1418 Done 1419 testpmd> port close 0 1420 Closing ports... 1421 Done 1422 1423 testpmd> port detach 0 1424 Detaching a port... 1425 EAL: PCI device 0000:0a:00.0 on NUMA socket -1 1426 EAL: remove driver: 8086:10fb rte_ixgbe_pmd 1427 EAL: PCI memory unmapped at 0x7f83bfa00000 1428 EAL: PCI memory unmapped at 0x7f83bfa80000 1429 Done 1430 1431 1432For example, to detach a virtual device port 0. 1433 1434.. code-block:: console 1435 1436 testpmd> port stop 0 1437 Stopping ports... 1438 Done 1439 testpmd> port close 0 1440 Closing ports... 1441 Done 1442 1443 testpmd> port detach 0 1444 Detaching a port... 1445 PMD: Closing pcap ethdev on numa socket 0 1446 Port 'net_pcap0' is detached. Now total ports is 0 1447 Done 1448 1449To remove a pci device completely from the system, first detach the port from testpmd. 1450Then the device should be moved under kernel management. 1451Finally the device can be removed using kernel pci hotplug functionality. 1452 1453For example, to move a pci device under kernel management: 1454 1455.. code-block:: console 1456 1457 sudo ./usertools/dpdk-devbind.py -b ixgbe 0000:0a:00.0 1458 1459 ./usertools/dpdk-devbind.py --status 1460 1461 Network devices using DPDK-compatible driver 1462 ============================================ 1463 <none> 1464 1465 Network devices using kernel driver 1466 =================================== 1467 0000:0a:00.0 '82599ES 10-Gigabit' if=eth2 drv=ixgbe unused=igb_uio 1468 1469To remove a port created by a virtual device, above steps are not needed. 1470 1471port start 1472~~~~~~~~~~ 1473 1474Start all ports or a specific port:: 1475 1476 testpmd> port start (port_id|all) 1477 1478port stop 1479~~~~~~~~~ 1480 1481Stop all ports or a specific port:: 1482 1483 testpmd> port stop (port_id|all) 1484 1485port close 1486~~~~~~~~~~ 1487 1488Close all ports or a specific port:: 1489 1490 testpmd> port close (port_id|all) 1491 1492port start/stop queue 1493~~~~~~~~~~~~~~~~~~~~~ 1494 1495Start/stop a rx/tx queue on a specific port:: 1496 1497 testpmd> port (port_id) (rxq|txq) (queue_id) (start|stop) 1498 1499Only take effect when port is started. 1500 1501port config - speed 1502~~~~~~~~~~~~~~~~~~~ 1503 1504Set the speed and duplex mode for all ports or a specific port:: 1505 1506 testpmd> port config (port_id|all) speed (10|100|1000|10000|25000|40000|50000|100000|auto) \ 1507 duplex (half|full|auto) 1508 1509port config - queues/descriptors 1510~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1511 1512Set number of queues/descriptors for rxq, txq, rxd and txd:: 1513 1514 testpmd> port config all (rxq|txq|rxd|txd) (value) 1515 1516This is equivalent to the ``--rxq``, ``--txq``, ``--rxd`` and ``--txd`` command-line options. 1517 1518port config - max-pkt-len 1519~~~~~~~~~~~~~~~~~~~~~~~~~ 1520 1521Set the maximum packet length:: 1522 1523 testpmd> port config all max-pkt-len (value) 1524 1525This is equivalent to the ``--max-pkt-len`` command-line option. 1526 1527port config - CRC Strip 1528~~~~~~~~~~~~~~~~~~~~~~~ 1529 1530Set hardware CRC stripping on or off for all ports:: 1531 1532 testpmd> port config all crc-strip (on|off) 1533 1534CRC stripping is on by default. 1535 1536The ``off`` option is equivalent to the ``--disable-crc-strip`` command-line option. 1537 1538port config - scatter 1539~~~~~~~~~~~~~~~~~~~~~~~ 1540 1541Set RX scatter mode on or off for all ports:: 1542 1543 testpmd> port config all scatter (on|off) 1544 1545RX scatter mode is off by default. 1546 1547The ``on`` option is equivalent to the ``--enable-scatter`` command-line option. 1548 1549port config - TX queue flags 1550~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1551 1552Set a hexadecimal bitmap of TX queue flags for all ports:: 1553 1554 testpmd> port config all txqflags value 1555 1556This command is equivalent to the ``--txqflags`` command-line option. 1557 1558port config - RX Checksum 1559~~~~~~~~~~~~~~~~~~~~~~~~~ 1560 1561Set hardware RX checksum offload to on or off for all ports:: 1562 1563 testpmd> port config all rx-cksum (on|off) 1564 1565Checksum offload is off by default. 1566 1567The ``on`` option is equivalent to the ``--enable-rx-cksum`` command-line option. 1568 1569port config - VLAN 1570~~~~~~~~~~~~~~~~~~ 1571 1572Set hardware VLAN on or off for all ports:: 1573 1574 testpmd> port config all hw-vlan (on|off) 1575 1576Hardware VLAN is on by default. 1577 1578The ``off`` option is equivalent to the ``--disable-hw-vlan`` command-line option. 1579 1580port config - VLAN filter 1581~~~~~~~~~~~~~~~~~~~~~~~~~ 1582 1583Set hardware VLAN filter on or off for all ports:: 1584 1585 testpmd> port config all hw-vlan-filter (on|off) 1586 1587Hardware VLAN filter is on by default. 1588 1589The ``off`` option is equivalent to the ``--disable-hw-vlan-filter`` command-line option. 1590 1591port config - VLAN strip 1592~~~~~~~~~~~~~~~~~~~~~~~~ 1593 1594Set hardware VLAN strip on or off for all ports:: 1595 1596 testpmd> port config all hw-vlan-strip (on|off) 1597 1598Hardware VLAN strip is on by default. 1599 1600The ``off`` option is equivalent to the ``--disable-hw-vlan-strip`` command-line option. 1601 1602port config - VLAN extend 1603~~~~~~~~~~~~~~~~~~~~~~~~~ 1604 1605Set hardware VLAN extend on or off for all ports:: 1606 1607 testpmd> port config all hw-vlan-extend (on|off) 1608 1609Hardware VLAN extend is off by default. 1610 1611The ``off`` option is equivalent to the ``--disable-hw-vlan-extend`` command-line option. 1612 1613port config - Drop Packets 1614~~~~~~~~~~~~~~~~~~~~~~~~~~ 1615 1616Set packet drop for packets with no descriptors on or off for all ports:: 1617 1618 testpmd> port config all drop-en (on|off) 1619 1620Packet dropping for packets with no descriptors is off by default. 1621 1622The ``on`` option is equivalent to the ``--enable-drop-en`` command-line option. 1623 1624port config - RSS 1625~~~~~~~~~~~~~~~~~ 1626 1627Set the RSS (Receive Side Scaling) mode on or off:: 1628 1629 testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none) 1630 1631RSS is on by default. 1632 1633The ``none`` option is equivalent to the ``--disable-rss`` command-line option. 1634 1635port config - RSS Reta 1636~~~~~~~~~~~~~~~~~~~~~~ 1637 1638Set the RSS (Receive Side Scaling) redirection table:: 1639 1640 testpmd> port config all rss reta (hash,queue)[,(hash,queue)] 1641 1642port config - DCB 1643~~~~~~~~~~~~~~~~~ 1644 1645Set the DCB mode for an individual port:: 1646 1647 testpmd> port config (port_id) dcb vt (on|off) (traffic_class) pfc (on|off) 1648 1649The traffic class should be 4 or 8. 1650 1651port config - Burst 1652~~~~~~~~~~~~~~~~~~~ 1653 1654Set the number of packets per burst:: 1655 1656 testpmd> port config all burst (value) 1657 1658This is equivalent to the ``--burst`` command-line option. 1659 1660port config - Threshold 1661~~~~~~~~~~~~~~~~~~~~~~~ 1662 1663Set thresholds for TX/RX queues:: 1664 1665 testpmd> port config all (threshold) (value) 1666 1667Where the threshold type can be: 1668 1669* ``txpt:`` Set the prefetch threshold register of the TX rings, 0 <= value <= 255. 1670 1671* ``txht:`` Set the host threshold register of the TX rings, 0 <= value <= 255. 1672 1673* ``txwt:`` Set the write-back threshold register of the TX rings, 0 <= value <= 255. 1674 1675* ``rxpt:`` Set the prefetch threshold register of the RX rings, 0 <= value <= 255. 1676 1677* ``rxht:`` Set the host threshold register of the RX rings, 0 <= value <= 255. 1678 1679* ``rxwt:`` Set the write-back threshold register of the RX rings, 0 <= value <= 255. 1680 1681* ``txfreet:`` Set the transmit free threshold of the TX rings, 0 <= value <= txd. 1682 1683* ``rxfreet:`` Set the transmit free threshold of the RX rings, 0 <= value <= rxd. 1684 1685* ``txrst:`` Set the transmit RS bit threshold of TX rings, 0 <= value <= txd. 1686 1687These threshold options are also available from the command-line. 1688 1689port config - E-tag 1690~~~~~~~~~~~~~~~~~~~ 1691 1692Set the value of ether-type for E-tag:: 1693 1694 testpmd> port config (port_id|all) l2-tunnel E-tag ether-type (value) 1695 1696Enable/disable the E-tag support:: 1697 1698 testpmd> port config (port_id|all) l2-tunnel E-tag (enable|disable) 1699 1700 1701Link Bonding Functions 1702---------------------- 1703 1704The Link Bonding functions make it possible to dynamically create and 1705manage link bonding devices from within testpmd interactive prompt. 1706 1707create bonded device 1708~~~~~~~~~~~~~~~~~~~~ 1709 1710Create a new bonding device:: 1711 1712 testpmd> create bonded device (mode) (socket) 1713 1714For example, to create a bonded device in mode 1 on socket 0:: 1715 1716 testpmd> create bonded 1 0 1717 created new bonded device (port X) 1718 1719add bonding slave 1720~~~~~~~~~~~~~~~~~ 1721 1722Adds Ethernet device to a Link Bonding device:: 1723 1724 testpmd> add bonding slave (slave id) (port id) 1725 1726For example, to add Ethernet device (port 6) to a Link Bonding device (port 10):: 1727 1728 testpmd> add bonding slave 6 10 1729 1730 1731remove bonding slave 1732~~~~~~~~~~~~~~~~~~~~ 1733 1734Removes an Ethernet slave device from a Link Bonding device:: 1735 1736 testpmd> remove bonding slave (slave id) (port id) 1737 1738For example, to remove Ethernet slave device (port 6) to a Link Bonding device (port 10):: 1739 1740 testpmd> remove bonding slave 6 10 1741 1742set bonding mode 1743~~~~~~~~~~~~~~~~ 1744 1745Set the Link Bonding mode of a Link Bonding device:: 1746 1747 testpmd> set bonding mode (value) (port id) 1748 1749For example, to set the bonding mode of a Link Bonding device (port 10) to broadcast (mode 3):: 1750 1751 testpmd> set bonding mode 3 10 1752 1753set bonding primary 1754~~~~~~~~~~~~~~~~~~~ 1755 1756Set an Ethernet slave device as the primary device on a Link Bonding device:: 1757 1758 testpmd> set bonding primary (slave id) (port id) 1759 1760For example, to set the Ethernet slave device (port 6) as the primary port of a Link Bonding device (port 10):: 1761 1762 testpmd> set bonding primary 6 10 1763 1764set bonding mac 1765~~~~~~~~~~~~~~~ 1766 1767Set the MAC address of a Link Bonding device:: 1768 1769 testpmd> set bonding mac (port id) (mac) 1770 1771For example, to set the MAC address of a Link Bonding device (port 10) to 00:00:00:00:00:01:: 1772 1773 testpmd> set bonding mac 10 00:00:00:00:00:01 1774 1775set bonding xmit_balance_policy 1776~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1777 1778Set the transmission policy for a Link Bonding device when it is in Balance XOR mode:: 1779 1780 testpmd> set bonding xmit_balance_policy (port_id) (l2|l23|l34) 1781 1782For example, set a Link Bonding device (port 10) to use a balance policy of layer 3+4 (IP addresses & UDP ports):: 1783 1784 testpmd> set bonding xmit_balance_policy 10 l34 1785 1786 1787set bonding mon_period 1788~~~~~~~~~~~~~~~~~~~~~~ 1789 1790Set the link status monitoring polling period in milliseconds for a bonding device. 1791 1792This adds support for PMD slave devices which do not support link status interrupts. 1793When the mon_period is set to a value greater than 0 then all PMD's which do not support 1794link status ISR will be queried every polling interval to check if their link status has changed:: 1795 1796 testpmd> set bonding mon_period (port_id) (value) 1797 1798For example, to set the link status monitoring polling period of bonded device (port 5) to 150ms:: 1799 1800 testpmd> set bonding mon_period 5 150 1801 1802 1803set bonding lacp dedicated_queue 1804~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1805 1806Enable dedicated tx/rx queues on bonding devices slaves to handle LACP control plane traffic 1807when in mode 4 (link-aggregration-802.3ad):: 1808 1809 testpmd> set bonding lacp dedicated_queues (port_id) (enable|disable) 1810 1811 1812show bonding config 1813~~~~~~~~~~~~~~~~~~~ 1814 1815Show the current configuration of a Link Bonding device:: 1816 1817 testpmd> show bonding config (port id) 1818 1819For example, 1820to show the configuration a Link Bonding device (port 9) with 3 slave devices (1, 3, 4) 1821in balance mode with a transmission policy of layer 2+3:: 1822 1823 testpmd> show bonding config 9 1824 Bonding mode: 2 1825 Balance Xmit Policy: BALANCE_XMIT_POLICY_LAYER23 1826 Slaves (3): [1 3 4] 1827 Active Slaves (3): [1 3 4] 1828 Primary: [3] 1829 1830 1831Register Functions 1832------------------ 1833 1834The Register Functions can be used to read from and write to registers on the network card referenced by a port number. 1835This is mainly useful for debugging purposes. 1836Reference should be made to the appropriate datasheet for the network card for details on the register addresses 1837and fields that can be accessed. 1838 1839read reg 1840~~~~~~~~ 1841 1842Display the value of a port register:: 1843 1844 testpmd> read reg (port_id) (address) 1845 1846For example, to examine the Flow Director control register (FDIRCTL, 0x0000EE000) on an Intel 82599 10 GbE Controller:: 1847 1848 testpmd> read reg 0 0xEE00 1849 port 0 PCI register at offset 0xEE00: 0x4A060029 (1241907241) 1850 1851read regfield 1852~~~~~~~~~~~~~ 1853 1854Display a port register bit field:: 1855 1856 testpmd> read regfield (port_id) (address) (bit_x) (bit_y) 1857 1858For example, reading the lowest two bits from the register in the example above:: 1859 1860 testpmd> read regfield 0 0xEE00 0 1 1861 port 0 PCI register at offset 0xEE00: bits[0, 1]=0x1 (1) 1862 1863read regbit 1864~~~~~~~~~~~ 1865 1866Display a single port register bit:: 1867 1868 testpmd> read regbit (port_id) (address) (bit_x) 1869 1870For example, reading the lowest bit from the register in the example above:: 1871 1872 testpmd> read regbit 0 0xEE00 0 1873 port 0 PCI register at offset 0xEE00: bit 0=1 1874 1875write reg 1876~~~~~~~~~ 1877 1878Set the value of a port register:: 1879 1880 testpmd> write reg (port_id) (address) (value) 1881 1882For example, to clear a register:: 1883 1884 testpmd> write reg 0 0xEE00 0x0 1885 port 0 PCI register at offset 0xEE00: 0x00000000 (0) 1886 1887write regfield 1888~~~~~~~~~~~~~~ 1889 1890Set bit field of a port register:: 1891 1892 testpmd> write regfield (port_id) (address) (bit_x) (bit_y) (value) 1893 1894For example, writing to the register cleared in the example above:: 1895 1896 testpmd> write regfield 0 0xEE00 0 1 2 1897 port 0 PCI register at offset 0xEE00: 0x00000002 (2) 1898 1899write regbit 1900~~~~~~~~~~~~ 1901 1902Set single bit value of a port register:: 1903 1904 testpmd> write regbit (port_id) (address) (bit_x) (value) 1905 1906For example, to set the high bit in the register from the example above:: 1907 1908 testpmd> write regbit 0 0xEE00 31 1 1909 port 0 PCI register at offset 0xEE00: 0x8000000A (2147483658) 1910 1911 1912Filter Functions 1913---------------- 1914 1915This section details the available filter functions that are available. 1916 1917Note these functions interface the deprecated legacy filtering framework, 1918superseded by *rte_flow*. See `Flow rules management`_. 1919 1920ethertype_filter 1921~~~~~~~~~~~~~~~~~~~~ 1922 1923Add or delete a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive queue:: 1924 1925 ethertype_filter (port_id) (add|del) (mac_addr|mac_ignr) (mac_address) \ 1926 ethertype (ether_type) (drop|fwd) queue (queue_id) 1927 1928The available information parameters are: 1929 1930* ``port_id``: The port which the Ethertype filter assigned on. 1931 1932* ``mac_addr``: Compare destination mac address. 1933 1934* ``mac_ignr``: Ignore destination mac address match. 1935 1936* ``mac_address``: Destination mac address to match. 1937 1938* ``ether_type``: The EtherType value want to match, 1939 for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid. 1940 1941* ``queue_id``: The receive queue associated with this EtherType filter. 1942 It is meaningless when deleting or dropping. 1943 1944Example, to add/remove an ethertype filter rule:: 1945 1946 testpmd> ethertype_filter 0 add mac_ignr 00:11:22:33:44:55 \ 1947 ethertype 0x0806 fwd queue 3 1948 1949 testpmd> ethertype_filter 0 del mac_ignr 00:11:22:33:44:55 \ 1950 ethertype 0x0806 fwd queue 3 1951 19522tuple_filter 1953~~~~~~~~~~~~~~~~~ 1954 1955Add or delete a 2-tuple filter, 1956which identifies packets by specific protocol and destination TCP/UDP port 1957and forwards packets into one of the receive queues:: 1958 1959 2tuple_filter (port_id) (add|del) dst_port (dst_port_value) \ 1960 protocol (protocol_value) mask (mask_value) \ 1961 tcp_flags (tcp_flags_value) priority (prio_value) \ 1962 queue (queue_id) 1963 1964The available information parameters are: 1965 1966* ``port_id``: The port which the 2-tuple filter assigned on. 1967 1968* ``dst_port_value``: Destination port in L4. 1969 1970* ``protocol_value``: IP L4 protocol. 1971 1972* ``mask_value``: Participates in the match or not by bit for field above, 1b means participate. 1973 1974* ``tcp_flags_value``: TCP control bits. The non-zero value is invalid, when the pro_value is not set to 0x06 (TCP). 1975 1976* ``prio_value``: Priority of this filter. 1977 1978* ``queue_id``: The receive queue associated with this 2-tuple filter. 1979 1980Example, to add/remove an 2tuple filter rule:: 1981 1982 testpmd> 2tuple_filter 0 add dst_port 32 protocol 0x06 mask 0x03 \ 1983 tcp_flags 0x02 priority 3 queue 3 1984 1985 testpmd> 2tuple_filter 0 del dst_port 32 protocol 0x06 mask 0x03 \ 1986 tcp_flags 0x02 priority 3 queue 3 1987 19885tuple_filter 1989~~~~~~~~~~~~~~~~~ 1990 1991Add or delete a 5-tuple filter, 1992which consists of a 5-tuple (protocol, source and destination IP addresses, source and destination TCP/UDP/SCTP port) 1993and routes packets into one of the receive queues:: 1994 1995 5tuple_filter (port_id) (add|del) dst_ip (dst_address) src_ip \ 1996 (src_address) dst_port (dst_port_value) \ 1997 src_port (src_port_value) protocol (protocol_value) \ 1998 mask (mask_value) tcp_flags (tcp_flags_value) \ 1999 priority (prio_value) queue (queue_id) 2000 2001The available information parameters are: 2002 2003* ``port_id``: The port which the 5-tuple filter assigned on. 2004 2005* ``dst_address``: Destination IP address. 2006 2007* ``src_address``: Source IP address. 2008 2009* ``dst_port_value``: TCP/UDP destination port. 2010 2011* ``src_port_value``: TCP/UDP source port. 2012 2013* ``protocol_value``: L4 protocol. 2014 2015* ``mask_value``: Participates in the match or not by bit for field above, 1b means participate 2016 2017* ``tcp_flags_value``: TCP control bits. The non-zero value is invalid, when the protocol_value is not set to 0x06 (TCP). 2018 2019* ``prio_value``: The priority of this filter. 2020 2021* ``queue_id``: The receive queue associated with this 5-tuple filter. 2022 2023Example, to add/remove an 5tuple filter rule:: 2024 2025 testpmd> 5tuple_filter 0 add dst_ip 2.2.2.5 src_ip 2.2.2.4 \ 2026 dst_port 64 src_port 32 protocol 0x06 mask 0x1F \ 2027 flags 0x0 priority 3 queue 3 2028 2029 testpmd> 5tuple_filter 0 del dst_ip 2.2.2.5 src_ip 2.2.2.4 \ 2030 dst_port 64 src_port 32 protocol 0x06 mask 0x1F \ 2031 flags 0x0 priority 3 queue 3 2032 2033syn_filter 2034~~~~~~~~~~ 2035 2036Using the SYN filter, TCP packets whose *SYN* flag is set can be forwarded to a separate queue:: 2037 2038 syn_filter (port_id) (add|del) priority (high|low) queue (queue_id) 2039 2040The available information parameters are: 2041 2042* ``port_id``: The port which the SYN filter assigned on. 2043 2044* ``high``: This SYN filter has higher priority than other filters. 2045 2046* ``low``: This SYN filter has lower priority than other filters. 2047 2048* ``queue_id``: The receive queue associated with this SYN filter 2049 2050Example:: 2051 2052 testpmd> syn_filter 0 add priority high queue 3 2053 2054flex_filter 2055~~~~~~~~~~~ 2056 2057With flex filter, packets can be recognized by any arbitrary pattern within the first 128 bytes of the packet 2058and routed into one of the receive queues:: 2059 2060 flex_filter (port_id) (add|del) len (len_value) bytes (bytes_value) \ 2061 mask (mask_value) priority (prio_value) queue (queue_id) 2062 2063The available information parameters are: 2064 2065* ``port_id``: The port which the Flex filter is assigned on. 2066 2067* ``len_value``: Filter length in bytes, no greater than 128. 2068 2069* ``bytes_value``: A string in hexadecimal, means the value the flex filter needs to match. 2070 2071* ``mask_value``: A string in hexadecimal, bit 1 means corresponding byte participates in the match. 2072 2073* ``prio_value``: The priority of this filter. 2074 2075* ``queue_id``: The receive queue associated with this Flex filter. 2076 2077Example:: 2078 2079 testpmd> flex_filter 0 add len 16 bytes 0x00000000000000000000000008060000 \ 2080 mask 000C priority 3 queue 3 2081 2082 testpmd> flex_filter 0 del len 16 bytes 0x00000000000000000000000008060000 \ 2083 mask 000C priority 3 queue 3 2084 2085 2086.. _testpmd_flow_director: 2087 2088flow_director_filter 2089~~~~~~~~~~~~~~~~~~~~ 2090 2091The Flow Director works in receive mode to identify specific flows or sets of flows and route them to specific queues. 2092 2093Four types of filtering are supported which are referred to as Perfect Match, Signature, Perfect-mac-vlan and 2094Perfect-tunnel filters, the match mode is set by the ``--pkt-filter-mode`` command-line parameter: 2095 2096* Perfect match filters. 2097 The hardware checks a match between the masked fields of the received packets and the programmed filters. 2098 The masked fields are for IP flow. 2099 2100* Signature filters. 2101 The hardware checks a match between a hash-based signature of the masked fields of the received packet. 2102 2103* Perfect-mac-vlan match filters. 2104 The hardware checks a match between the masked fields of the received packets and the programmed filters. 2105 The masked fields are for MAC VLAN flow. 2106 2107* Perfect-tunnel match filters. 2108 The hardware checks a match between the masked fields of the received packets and the programmed filters. 2109 The masked fields are for tunnel flow. 2110 2111The Flow Director filters can match the different fields for different type of packet: flow type, specific input set 2112per flow type and the flexible payload. 2113 2114The Flow Director can also mask out parts of all of these fields so that filters 2115are only applied to certain fields or parts of the fields. 2116 2117Different NICs may have different capabilities, command show port fdir (port_id) can be used to acquire the information. 2118 2119# Commands to add flow director filters of different flow types:: 2120 2121 flow_director_filter (port_id) mode IP (add|del|update) \ 2122 flow (ipv4-other|ipv4-frag|ipv6-other|ipv6-frag) \ 2123 src (src_ip_address) dst (dst_ip_address) \ 2124 tos (tos_value) proto (proto_value) ttl (ttl_value) \ 2125 vlan (vlan_value) flexbytes (flexbytes_value) \ 2126 (drop|fwd) pf|vf(vf_id) queue (queue_id) \ 2127 fd_id (fd_id_value) 2128 2129 flow_director_filter (port_id) mode IP (add|del|update) \ 2130 flow (ipv4-tcp|ipv4-udp|ipv6-tcp|ipv6-udp) \ 2131 src (src_ip_address) (src_port) \ 2132 dst (dst_ip_address) (dst_port) \ 2133 tos (tos_value) ttl (ttl_value) \ 2134 vlan (vlan_value) flexbytes (flexbytes_value) \ 2135 (drop|fwd) queue pf|vf(vf_id) (queue_id) \ 2136 fd_id (fd_id_value) 2137 2138 flow_director_filter (port_id) mode IP (add|del|update) \ 2139 flow (ipv4-sctp|ipv6-sctp) \ 2140 src (src_ip_address) (src_port) \ 2141 dst (dst_ip_address) (dst_port) \ 2142 tos (tos_value) ttl (ttl_value) \ 2143 tag (verification_tag) vlan (vlan_value) \ 2144 flexbytes (flexbytes_value) (drop|fwd) \ 2145 pf|vf(vf_id) queue (queue_id) fd_id (fd_id_value) 2146 2147 flow_director_filter (port_id) mode IP (add|del|update) flow l2_payload \ 2148 ether (ethertype) flexbytes (flexbytes_value) \ 2149 (drop|fwd) pf|vf(vf_id) queue (queue_id) 2150 fd_id (fd_id_value) 2151 2152 flow_director_filter (port_id) mode MAC-VLAN (add|del|update) \ 2153 mac (mac_address) vlan (vlan_value) \ 2154 flexbytes (flexbytes_value) (drop|fwd) \ 2155 queue (queue_id) fd_id (fd_id_value) 2156 2157 flow_director_filter (port_id) mode Tunnel (add|del|update) \ 2158 mac (mac_address) vlan (vlan_value) \ 2159 tunnel (NVGRE|VxLAN) tunnel-id (tunnel_id_value) \ 2160 flexbytes (flexbytes_value) (drop|fwd) \ 2161 queue (queue_id) fd_id (fd_id_value) 2162 2163For example, to add an ipv4-udp flow type filter:: 2164 2165 testpmd> flow_director_filter 0 mode IP add flow ipv4-udp src 2.2.2.3 32 \ 2166 dst 2.2.2.5 33 tos 2 ttl 40 vlan 0x1 flexbytes (0x88,0x48) \ 2167 fwd pf queue 1 fd_id 1 2168 2169For example, add an ipv4-other flow type filter:: 2170 2171 testpmd> flow_director_filter 0 mode IP add flow ipv4-other src 2.2.2.3 \ 2172 dst 2.2.2.5 tos 2 proto 20 ttl 40 vlan 0x1 \ 2173 flexbytes (0x88,0x48) fwd pf queue 1 fd_id 1 2174 2175flush_flow_director 2176~~~~~~~~~~~~~~~~~~~ 2177 2178Flush all flow director filters on a device:: 2179 2180 testpmd> flush_flow_director (port_id) 2181 2182Example, to flush all flow director filter on port 0:: 2183 2184 testpmd> flush_flow_director 0 2185 2186flow_director_mask 2187~~~~~~~~~~~~~~~~~~ 2188 2189Set flow director's input masks:: 2190 2191 flow_director_mask (port_id) mode IP vlan (vlan_value) \ 2192 src_mask (ipv4_src) (ipv6_src) (src_port) \ 2193 dst_mask (ipv4_dst) (ipv6_dst) (dst_port) 2194 2195 flow_director_mask (port_id) mode MAC-VLAN vlan (vlan_value) 2196 2197 flow_director_mask (port_id) mode Tunnel vlan (vlan_value) \ 2198 mac (mac_value) tunnel-type (tunnel_type_value) \ 2199 tunnel-id (tunnel_id_value) 2200 2201Example, to set flow director mask on port 0:: 2202 2203 testpmd> flow_director_mask 0 mode IP vlan 0xefff \ 2204 src_mask 255.255.255.255 \ 2205 FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0xFFFF \ 2206 dst_mask 255.255.255.255 \ 2207 FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0xFFFF 2208 2209flow_director_flex_mask 2210~~~~~~~~~~~~~~~~~~~~~~~ 2211 2212set masks of flow director's flexible payload based on certain flow type:: 2213 2214 testpmd> flow_director_flex_mask (port_id) \ 2215 flow (none|ipv4-other|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \ 2216 ipv6-other|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp| \ 2217 l2_payload|all) (mask) 2218 2219Example, to set flow director's flex mask for all flow type on port 0:: 2220 2221 testpmd> flow_director_flex_mask 0 flow all \ 2222 (0xff,0xff,0,0,0,0,0,0,0,0,0,0,0,0,0,0) 2223 2224 2225flow_director_flex_payload 2226~~~~~~~~~~~~~~~~~~~~~~~~~~ 2227 2228Configure flexible payload selection:: 2229 2230 flow_director_flex_payload (port_id) (raw|l2|l3|l4) (config) 2231 2232For example, to select the first 16 bytes from the offset 4 (bytes) of packet's payload as flexible payload:: 2233 2234 testpmd> flow_director_flex_payload 0 l4 \ 2235 (4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19) 2236 2237get_sym_hash_ena_per_port 2238~~~~~~~~~~~~~~~~~~~~~~~~~ 2239 2240Get symmetric hash enable configuration per port:: 2241 2242 get_sym_hash_ena_per_port (port_id) 2243 2244For example, to get symmetric hash enable configuration of port 1:: 2245 2246 testpmd> get_sym_hash_ena_per_port 1 2247 2248set_sym_hash_ena_per_port 2249~~~~~~~~~~~~~~~~~~~~~~~~~ 2250 2251Set symmetric hash enable configuration per port to enable or disable:: 2252 2253 set_sym_hash_ena_per_port (port_id) (enable|disable) 2254 2255For example, to set symmetric hash enable configuration of port 1 to enable:: 2256 2257 testpmd> set_sym_hash_ena_per_port 1 enable 2258 2259get_hash_global_config 2260~~~~~~~~~~~~~~~~~~~~~~ 2261 2262Get the global configurations of hash filters:: 2263 2264 get_hash_global_config (port_id) 2265 2266For example, to get the global configurations of hash filters of port 1:: 2267 2268 testpmd> get_hash_global_config 1 2269 2270set_hash_global_config 2271~~~~~~~~~~~~~~~~~~~~~~ 2272 2273Set the global configurations of hash filters:: 2274 2275 set_hash_global_config (port_id) (toeplitz|simple_xor|default) \ 2276 (ipv4|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp|ipv4-other|ipv6|ipv6-frag| \ 2277 ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other|l2_payload) \ 2278 (enable|disable) 2279 2280For example, to enable simple_xor for flow type of ipv6 on port 2:: 2281 2282 testpmd> set_hash_global_config 2 simple_xor ipv6 enable 2283 2284set_hash_input_set 2285~~~~~~~~~~~~~~~~~~ 2286 2287Set the input set for hash:: 2288 2289 set_hash_input_set (port_id) (ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \ 2290 ipv4-other|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other| \ 2291 l2_payload) (ovlan|ivlan|src-ipv4|dst-ipv4|src-ipv6|dst-ipv6|ipv4-tos| \ 2292 ipv4-proto|ipv6-tc|ipv6-next-header|udp-src-port|udp-dst-port| \ 2293 tcp-src-port|tcp-dst-port|sctp-src-port|sctp-dst-port|sctp-veri-tag| \ 2294 udp-key|gre-key|fld-1st|fld-2nd|fld-3rd|fld-4th|fld-5th|fld-6th|fld-7th| \ 2295 fld-8th|none) (select|add) 2296 2297For example, to add source IP to hash input set for flow type of ipv4-udp on port 0:: 2298 2299 testpmd> set_hash_input_set 0 ipv4-udp src-ipv4 add 2300 2301set_fdir_input_set 2302~~~~~~~~~~~~~~~~~~ 2303 2304The Flow Director filters can match the different fields for different type of packet, i.e. specific input set 2305on per flow type and the flexible payload. This command can be used to change input set for each flow type. 2306 2307Set the input set for flow director:: 2308 2309 set_fdir_input_set (port_id) (ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \ 2310 ipv4-other|ipv6|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other| \ 2311 l2_payload) (ivlan|ethertype|src-ipv4|dst-ipv4|src-ipv6|dst-ipv6|ipv4-tos| \ 2312 ipv4-proto|ipv4-ttl|ipv6-tc|ipv6-next-header|ipv6-hop-limits| \ 2313 tudp-src-port|udp-dst-port|cp-src-port|tcp-dst-port|sctp-src-port| \ 2314 sctp-dst-port|sctp-veri-tag|none) (select|add) 2315 2316For example to add source IP to FD input set for flow type of ipv4-udp on port 0:: 2317 2318 testpmd> set_fdir_input_set 0 ipv4-udp src-ipv4 add 2319 2320global_config 2321~~~~~~~~~~~~~ 2322 2323Set different GRE key length for input set:: 2324 2325 global_config (port_id) gre-key-len (number in bytes) 2326 2327For example to set GRE key length for input set to 4 bytes on port 0:: 2328 2329 testpmd> global_config 0 gre-key-len 4 2330 2331 2332.. _testpmd_rte_flow: 2333 2334Flow rules management 2335--------------------- 2336 2337Control of the generic flow API (*rte_flow*) is fully exposed through the 2338``flow`` command (validation, creation, destruction, queries and operation 2339modes). 2340 2341Considering *rte_flow* overlaps with all `Filter Functions`_, using both 2342features simultaneously may cause undefined side-effects and is therefore 2343not recommended. 2344 2345``flow`` syntax 2346~~~~~~~~~~~~~~~ 2347 2348Because the ``flow`` command uses dynamic tokens to handle the large number 2349of possible flow rules combinations, its behavior differs slightly from 2350other commands, in particular: 2351 2352- Pressing *?* or the *<tab>* key displays contextual help for the current 2353 token, not that of the entire command. 2354 2355- Optional and repeated parameters are supported (provided they are listed 2356 in the contextual help). 2357 2358The first parameter stands for the operation mode. Possible operations and 2359their general syntax are described below. They are covered in detail in the 2360following sections. 2361 2362- Check whether a flow rule can be created:: 2363 2364 flow validate {port_id} 2365 [group {group_id}] [priority {level}] [ingress] [egress] 2366 pattern {item} [/ {item} [...]] / end 2367 actions {action} [/ {action} [...]] / end 2368 2369- Create a flow rule:: 2370 2371 flow create {port_id} 2372 [group {group_id}] [priority {level}] [ingress] [egress] 2373 pattern {item} [/ {item} [...]] / end 2374 actions {action} [/ {action} [...]] / end 2375 2376- Destroy specific flow rules:: 2377 2378 flow destroy {port_id} rule {rule_id} [...] 2379 2380- Destroy all flow rules:: 2381 2382 flow flush {port_id} 2383 2384- Query an existing flow rule:: 2385 2386 flow query {port_id} {rule_id} {action} 2387 2388- List existing flow rules sorted by priority, filtered by group 2389 identifiers:: 2390 2391 flow list {port_id} [group {group_id}] [...] 2392 2393- Restrict ingress traffic to the defined flow rules:: 2394 2395 flow isolate {port_id} {boolean} 2396 2397Validating flow rules 2398~~~~~~~~~~~~~~~~~~~~~ 2399 2400``flow validate`` reports whether a flow rule would be accepted by the 2401underlying device in its current state but stops short of creating it. It is 2402bound to ``rte_flow_validate()``:: 2403 2404 flow validate {port_id} 2405 [group {group_id}] [priority {level}] [ingress] [egress] 2406 pattern {item} [/ {item} [...]] / end 2407 actions {action} [/ {action} [...]] / end 2408 2409If successful, it will show:: 2410 2411 Flow rule validated 2412 2413Otherwise it will show an error message of the form:: 2414 2415 Caught error type [...] ([...]): [...] 2416 2417This command uses the same parameters as ``flow create``, their format is 2418described in `Creating flow rules`_. 2419 2420Check whether redirecting any Ethernet packet received on port 0 to RX queue 2421index 6 is supported:: 2422 2423 testpmd> flow validate 0 ingress pattern eth / end 2424 actions queue index 6 / end 2425 Flow rule validated 2426 testpmd> 2427 2428Port 0 does not support TCPv6 rules:: 2429 2430 testpmd> flow validate 0 ingress pattern eth / ipv6 / tcp / end 2431 actions drop / end 2432 Caught error type 9 (specific pattern item): Invalid argument 2433 testpmd> 2434 2435Creating flow rules 2436~~~~~~~~~~~~~~~~~~~ 2437 2438``flow create`` validates and creates the specified flow rule. It is bound 2439to ``rte_flow_create()``:: 2440 2441 flow create {port_id} 2442 [group {group_id}] [priority {level}] [ingress] [egress] 2443 pattern {item} [/ {item} [...]] / end 2444 actions {action} [/ {action} [...]] / end 2445 2446If successful, it will return a flow rule ID usable with other commands:: 2447 2448 Flow rule #[...] created 2449 2450Otherwise it will show an error message of the form:: 2451 2452 Caught error type [...] ([...]): [...] 2453 2454Parameters describe in the following order: 2455 2456- Attributes (*group*, *priority*, *ingress*, *egress* tokens). 2457- A matching pattern, starting with the *pattern* token and terminated by an 2458 *end* pattern item. 2459- Actions, starting with the *actions* token and terminated by an *end* 2460 action. 2461 2462These translate directly to *rte_flow* objects provided as-is to the 2463underlying functions. 2464 2465The shortest valid definition only comprises mandatory tokens:: 2466 2467 testpmd> flow create 0 pattern end actions end 2468 2469Note that PMDs may refuse rules that essentially do nothing such as this 2470one. 2471 2472**All unspecified object values are automatically initialized to 0.** 2473 2474Attributes 2475^^^^^^^^^^ 2476 2477These tokens affect flow rule attributes (``struct rte_flow_attr``) and are 2478specified before the ``pattern`` token. 2479 2480- ``group {group id}``: priority group. 2481- ``priority {level}``: priority level within group. 2482- ``ingress``: rule applies to ingress traffic. 2483- ``egress``: rule applies to egress traffic. 2484 2485Each instance of an attribute specified several times overrides the previous 2486value as shown below (group 4 is used):: 2487 2488 testpmd> flow create 0 group 42 group 24 group 4 [...] 2489 2490Note that once enabled, ``ingress`` and ``egress`` cannot be disabled. 2491 2492While not specifying a direction is an error, some rules may allow both 2493simultaneously. 2494 2495Most rules affect RX therefore contain the ``ingress`` token:: 2496 2497 testpmd> flow create 0 ingress pattern [...] 2498 2499Matching pattern 2500^^^^^^^^^^^^^^^^ 2501 2502A matching pattern starts after the ``pattern`` token. It is made of pattern 2503items and is terminated by a mandatory ``end`` item. 2504 2505Items are named after their type (*RTE_FLOW_ITEM_TYPE_* from ``enum 2506rte_flow_item_type``). 2507 2508The ``/`` token is used as a separator between pattern items as shown 2509below:: 2510 2511 testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end [...] 2512 2513Note that protocol items like these must be stacked from lowest to highest 2514layer to make sense. For instance, the following rule is either invalid or 2515unlikely to match any packet:: 2516 2517 testpmd> flow create 0 ingress pattern eth / udp / ipv4 / end [...] 2518 2519More information on these restrictions can be found in the *rte_flow* 2520documentation. 2521 2522Several items support additional specification structures, for example 2523``ipv4`` allows specifying source and destination addresses as follows:: 2524 2525 testpmd> flow create 0 ingress pattern eth / ipv4 src is 10.1.1.1 2526 dst is 10.2.0.0 / end [...] 2527 2528This rule matches all IPv4 traffic with the specified properties. 2529 2530In this example, ``src`` and ``dst`` are field names of the underlying 2531``struct rte_flow_item_ipv4`` object. All item properties can be specified 2532in a similar fashion. 2533 2534The ``is`` token means that the subsequent value must be matched exactly, 2535and assigns ``spec`` and ``mask`` fields in ``struct rte_flow_item`` 2536accordingly. Possible assignment tokens are: 2537 2538- ``is``: match value perfectly (with full bit-mask). 2539- ``spec``: match value according to configured bit-mask. 2540- ``last``: specify upper bound to establish a range. 2541- ``mask``: specify bit-mask with relevant bits set to one. 2542- ``prefix``: generate bit-mask from a prefix length. 2543 2544These yield identical results:: 2545 2546 ipv4 src is 10.1.1.1 2547 2548:: 2549 2550 ipv4 src spec 10.1.1.1 src mask 255.255.255.255 2551 2552:: 2553 2554 ipv4 src spec 10.1.1.1 src prefix 32 2555 2556:: 2557 2558 ipv4 src is 10.1.1.1 src last 10.1.1.1 # range with a single value 2559 2560:: 2561 2562 ipv4 src is 10.1.1.1 src last 0 # 0 disables range 2563 2564Inclusive ranges can be defined with ``last``:: 2565 2566 ipv4 src is 10.1.1.1 src last 10.2.3.4 # 10.1.1.1 to 10.2.3.4 2567 2568Note that ``mask`` affects both ``spec`` and ``last``:: 2569 2570 ipv4 src is 10.1.1.1 src last 10.2.3.4 src mask 255.255.0.0 2571 # matches 10.1.0.0 to 10.2.255.255 2572 2573Properties can be modified multiple times:: 2574 2575 ipv4 src is 10.1.1.1 src is 10.1.2.3 src is 10.2.3.4 # matches 10.2.3.4 2576 2577:: 2578 2579 ipv4 src is 10.1.1.1 src prefix 24 src prefix 16 # matches 10.1.0.0/16 2580 2581Pattern items 2582^^^^^^^^^^^^^ 2583 2584This section lists supported pattern items and their attributes, if any. 2585 2586- ``end``: end list of pattern items. 2587 2588- ``void``: no-op pattern item. 2589 2590- ``invert``: perform actions when pattern does not match. 2591 2592- ``any``: match any protocol for the current layer. 2593 2594 - ``num {unsigned}``: number of layers covered. 2595 2596- ``pf``: match packets addressed to the physical function. 2597 2598- ``vf``: match packets addressed to a virtual function ID. 2599 2600 - ``id {unsigned}``: destination VF ID. 2601 2602- ``port``: device-specific physical port index to use. 2603 2604 - ``index {unsigned}``: physical port index. 2605 2606- ``raw``: match an arbitrary byte string. 2607 2608 - ``relative {boolean}``: look for pattern after the previous item. 2609 - ``search {boolean}``: search pattern from offset (see also limit). 2610 - ``offset {integer}``: absolute or relative offset for pattern. 2611 - ``limit {unsigned}``: search area limit for start of pattern. 2612 - ``pattern {string}``: byte string to look for. 2613 2614- ``eth``: match Ethernet header. 2615 2616 - ``dst {MAC-48}``: destination MAC. 2617 - ``src {MAC-48}``: source MAC. 2618 - ``type {unsigned}``: EtherType. 2619 2620- ``vlan``: match 802.1Q/ad VLAN tag. 2621 2622 - ``tpid {unsigned}``: tag protocol identifier. 2623 - ``tci {unsigned}``: tag control information. 2624 - ``pcp {unsigned}``: priority code point. 2625 - ``dei {unsigned}``: drop eligible indicator. 2626 - ``vid {unsigned}``: VLAN identifier. 2627 2628- ``ipv4``: match IPv4 header. 2629 2630 - ``tos {unsigned}``: type of service. 2631 - ``ttl {unsigned}``: time to live. 2632 - ``proto {unsigned}``: next protocol ID. 2633 - ``src {ipv4 address}``: source address. 2634 - ``dst {ipv4 address}``: destination address. 2635 2636- ``ipv6``: match IPv6 header. 2637 2638 - ``tc {unsigned}``: traffic class. 2639 - ``flow {unsigned}``: flow label. 2640 - ``proto {unsigned}``: protocol (next header). 2641 - ``hop {unsigned}``: hop limit. 2642 - ``src {ipv6 address}``: source address. 2643 - ``dst {ipv6 address}``: destination address. 2644 2645- ``icmp``: match ICMP header. 2646 2647 - ``type {unsigned}``: ICMP packet type. 2648 - ``code {unsigned}``: ICMP packet code. 2649 2650- ``udp``: match UDP header. 2651 2652 - ``src {unsigned}``: UDP source port. 2653 - ``dst {unsigned}``: UDP destination port. 2654 2655- ``tcp``: match TCP header. 2656 2657 - ``src {unsigned}``: TCP source port. 2658 - ``dst {unsigned}``: TCP destination port. 2659 2660- ``sctp``: match SCTP header. 2661 2662 - ``src {unsigned}``: SCTP source port. 2663 - ``dst {unsigned}``: SCTP destination port. 2664 - ``tag {unsigned}``: validation tag. 2665 - ``cksum {unsigned}``: checksum. 2666 2667- ``vxlan``: match VXLAN header. 2668 2669 - ``vni {unsigned}``: VXLAN identifier. 2670 2671- ``e_tag``: match IEEE 802.1BR E-Tag header. 2672 2673 - ``grp_ecid_b {unsigned}``: GRP and E-CID base. 2674 2675- ``nvgre``: match NVGRE header. 2676 2677 - ``tni {unsigned}``: virtual subnet ID. 2678 2679- ``mpls``: match MPLS header. 2680 2681 - ``label {unsigned}``: MPLS label. 2682 2683- ``gre``: match GRE header. 2684 2685 - ``protocol {unsigned}``: protocol type. 2686 2687- ``fuzzy``: fuzzy pattern match, expect faster than default. 2688 2689 - ``thresh {unsigned}``: accuracy threshold. 2690 2691Actions list 2692^^^^^^^^^^^^ 2693 2694A list of actions starts after the ``actions`` token in the same fashion as 2695`Matching pattern`_; actions are separated by ``/`` tokens and the list is 2696terminated by a mandatory ``end`` action. 2697 2698Actions are named after their type (*RTE_FLOW_ACTION_TYPE_* from ``enum 2699rte_flow_action_type``). 2700 2701Dropping all incoming UDPv4 packets can be expressed as follows:: 2702 2703 testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end 2704 actions drop / end 2705 2706Several actions have configurable properties which must be specified when 2707there is no valid default value. For example, ``queue`` requires a target 2708queue index. 2709 2710This rule redirects incoming UDPv4 traffic to queue index 6:: 2711 2712 testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end 2713 actions queue index 6 / end 2714 2715While this one could be rejected by PMDs (unspecified queue index):: 2716 2717 testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end 2718 actions queue / end 2719 2720As defined by *rte_flow*, the list is not ordered, all actions of a given 2721rule are performed simultaneously. These are equivalent:: 2722 2723 queue index 6 / void / mark id 42 / end 2724 2725:: 2726 2727 void / mark id 42 / queue index 6 / end 2728 2729All actions in a list should have different types, otherwise only the last 2730action of a given type is taken into account:: 2731 2732 queue index 4 / queue index 5 / queue index 6 / end # will use queue 6 2733 2734:: 2735 2736 drop / drop / drop / end # drop is performed only once 2737 2738:: 2739 2740 mark id 42 / queue index 3 / mark id 24 / end # mark will be 24 2741 2742Considering they are performed simultaneously, opposite and overlapping 2743actions can sometimes be combined when the end result is unambiguous:: 2744 2745 drop / queue index 6 / end # drop has no effect 2746 2747:: 2748 2749 drop / dup index 6 / end # same as above 2750 2751:: 2752 2753 queue index 6 / rss queues 6 7 8 / end # queue has no effect 2754 2755:: 2756 2757 drop / passthru / end # drop has no effect 2758 2759Note that PMDs may still refuse such combinations. 2760 2761Actions 2762^^^^^^^ 2763 2764This section lists supported actions and their attributes, if any. 2765 2766- ``end``: end list of actions. 2767 2768- ``void``: no-op action. 2769 2770- ``passthru``: let subsequent rule process matched packets. 2771 2772- ``mark``: attach 32 bit value to packets. 2773 2774 - ``id {unsigned}``: 32 bit value to return with packets. 2775 2776- ``flag``: flag packets. 2777 2778- ``queue``: assign packets to a given queue index. 2779 2780 - ``index {unsigned}``: queue index to use. 2781 2782- ``drop``: drop packets (note: passthru has priority). 2783 2784- ``count``: enable counters for this rule. 2785 2786- ``dup``: duplicate packets to a given queue index. 2787 2788 - ``index {unsigned}``: queue index to duplicate packets to. 2789 2790- ``rss``: spread packets among several queues. 2791 2792 - ``queues [{unsigned} [...]] end``: queue indices to use. 2793 2794- ``pf``: redirect packets to physical device function. 2795 2796- ``vf``: redirect packets to virtual device function. 2797 2798 - ``original {boolean}``: use original VF ID if possible. 2799 - ``id {unsigned}``: VF ID to redirect packets to. 2800 2801Destroying flow rules 2802~~~~~~~~~~~~~~~~~~~~~ 2803 2804``flow destroy`` destroys one or more rules from their rule ID (as returned 2805by ``flow create``), this command calls ``rte_flow_destroy()`` as many 2806times as necessary:: 2807 2808 flow destroy {port_id} rule {rule_id} [...] 2809 2810If successful, it will show:: 2811 2812 Flow rule #[...] destroyed 2813 2814It does not report anything for rule IDs that do not exist. The usual error 2815message is shown when a rule cannot be destroyed:: 2816 2817 Caught error type [...] ([...]): [...] 2818 2819``flow flush`` destroys all rules on a device and does not take extra 2820arguments. It is bound to ``rte_flow_flush()``:: 2821 2822 flow flush {port_id} 2823 2824Any errors are reported as above. 2825 2826Creating several rules and destroying them:: 2827 2828 testpmd> flow create 0 ingress pattern eth / ipv6 / end 2829 actions queue index 2 / end 2830 Flow rule #0 created 2831 testpmd> flow create 0 ingress pattern eth / ipv4 / end 2832 actions queue index 3 / end 2833 Flow rule #1 created 2834 testpmd> flow destroy 0 rule 0 rule 1 2835 Flow rule #1 destroyed 2836 Flow rule #0 destroyed 2837 testpmd> 2838 2839The same result can be achieved using ``flow flush``:: 2840 2841 testpmd> flow create 0 ingress pattern eth / ipv6 / end 2842 actions queue index 2 / end 2843 Flow rule #0 created 2844 testpmd> flow create 0 ingress pattern eth / ipv4 / end 2845 actions queue index 3 / end 2846 Flow rule #1 created 2847 testpmd> flow flush 0 2848 testpmd> 2849 2850Non-existent rule IDs are ignored:: 2851 2852 testpmd> flow create 0 ingress pattern eth / ipv6 / end 2853 actions queue index 2 / end 2854 Flow rule #0 created 2855 testpmd> flow create 0 ingress pattern eth / ipv4 / end 2856 actions queue index 3 / end 2857 Flow rule #1 created 2858 testpmd> flow destroy 0 rule 42 rule 10 rule 2 2859 testpmd> 2860 testpmd> flow destroy 0 rule 0 2861 Flow rule #0 destroyed 2862 testpmd> 2863 2864Querying flow rules 2865~~~~~~~~~~~~~~~~~~~ 2866 2867``flow query`` queries a specific action of a flow rule having that 2868ability. Such actions collect information that can be reported using this 2869command. It is bound to ``rte_flow_query()``:: 2870 2871 flow query {port_id} {rule_id} {action} 2872 2873If successful, it will display either the retrieved data for known actions 2874or the following message:: 2875 2876 Cannot display result for action type [...] ([...]) 2877 2878Otherwise, it will complain either that the rule does not exist or that some 2879error occurred:: 2880 2881 Flow rule #[...] not found 2882 2883:: 2884 2885 Caught error type [...] ([...]): [...] 2886 2887Currently only the ``count`` action is supported. This action reports the 2888number of packets that hit the flow rule and the total number of bytes. Its 2889output has the following format:: 2890 2891 count: 2892 hits_set: [...] # whether "hits" contains a valid value 2893 bytes_set: [...] # whether "bytes" contains a valid value 2894 hits: [...] # number of packets 2895 bytes: [...] # number of bytes 2896 2897Querying counters for TCPv6 packets redirected to queue 6:: 2898 2899 testpmd> flow create 0 ingress pattern eth / ipv6 / tcp / end 2900 actions queue index 6 / count / end 2901 Flow rule #4 created 2902 testpmd> flow query 0 4 count 2903 count: 2904 hits_set: 1 2905 bytes_set: 0 2906 hits: 386446 2907 bytes: 0 2908 testpmd> 2909 2910Listing flow rules 2911~~~~~~~~~~~~~~~~~~ 2912 2913``flow list`` lists existing flow rules sorted by priority and optionally 2914filtered by group identifiers:: 2915 2916 flow list {port_id} [group {group_id}] [...] 2917 2918This command only fails with the following message if the device does not 2919exist:: 2920 2921 Invalid port [...] 2922 2923Output consists of a header line followed by a short description of each 2924flow rule, one per line. There is no output at all when no flow rules are 2925configured on the device:: 2926 2927 ID Group Prio Attr Rule 2928 [...] [...] [...] [...] [...] 2929 2930``Attr`` column flags: 2931 2932- ``i`` for ``ingress``. 2933- ``e`` for ``egress``. 2934 2935Creating several flow rules and listing them:: 2936 2937 testpmd> flow create 0 ingress pattern eth / ipv4 / end 2938 actions queue index 6 / end 2939 Flow rule #0 created 2940 testpmd> flow create 0 ingress pattern eth / ipv6 / end 2941 actions queue index 2 / end 2942 Flow rule #1 created 2943 testpmd> flow create 0 priority 5 ingress pattern eth / ipv4 / udp / end 2944 actions rss queues 6 7 8 end / end 2945 Flow rule #2 created 2946 testpmd> flow list 0 2947 ID Group Prio Attr Rule 2948 0 0 0 i- ETH IPV4 => QUEUE 2949 1 0 0 i- ETH IPV6 => QUEUE 2950 2 0 5 i- ETH IPV4 UDP => RSS 2951 testpmd> 2952 2953Rules are sorted by priority (i.e. group ID first, then priority level):: 2954 2955 testpmd> flow list 1 2956 ID Group Prio Attr Rule 2957 0 0 0 i- ETH => COUNT 2958 6 0 500 i- ETH IPV6 TCP => DROP COUNT 2959 5 0 1000 i- ETH IPV6 ICMP => QUEUE 2960 1 24 0 i- ETH IPV4 UDP => QUEUE 2961 4 24 10 i- ETH IPV4 TCP => DROP 2962 3 24 20 i- ETH IPV4 => DROP 2963 2 24 42 i- ETH IPV4 UDP => QUEUE 2964 7 63 0 i- ETH IPV6 UDP VXLAN => MARK QUEUE 2965 testpmd> 2966 2967Output can be limited to specific groups:: 2968 2969 testpmd> flow list 1 group 0 group 63 2970 ID Group Prio Attr Rule 2971 0 0 0 i- ETH => COUNT 2972 6 0 500 i- ETH IPV6 TCP => DROP COUNT 2973 5 0 1000 i- ETH IPV6 ICMP => QUEUE 2974 7 63 0 i- ETH IPV6 UDP VXLAN => MARK QUEUE 2975 testpmd> 2976 2977Toggling isolated mode 2978~~~~~~~~~~~~~~~~~~~~~~ 2979 2980``flow isolate`` can be used to tell the underlying PMD that ingress traffic 2981must only be injected from the defined flow rules; that no default traffic 2982is expected outside those rules and the driver is free to assign more 2983resources to handle them. It is bound to ``rte_flow_isolate()``:: 2984 2985 flow isolate {port_id} {boolean} 2986 2987If successful, enabling or disabling isolated mode shows either:: 2988 2989 Ingress traffic on port [...] 2990 is now restricted to the defined flow rules 2991 2992Or:: 2993 2994 Ingress traffic on port [...] 2995 is not restricted anymore to the defined flow rules 2996 2997Otherwise, in case of error:: 2998 2999 Caught error type [...] ([...]): [...] 3000 3001Mainly due to its side effects, PMDs supporting this mode may not have the 3002ability to toggle it more than once without reinitializing affected ports 3003first (e.g. by exiting testpmd). 3004 3005Enabling isolated mode:: 3006 3007 testpmd> flow isolate 0 true 3008 Ingress traffic on port 0 is now restricted to the defined flow rules 3009 testpmd> 3010 3011Disabling isolated mode:: 3012 3013 testpmd> flow isolate 0 false 3014 Ingress traffic on port 0 is not restricted anymore to the defined flow rules 3015 testpmd> 3016 3017Sample QinQ flow rules 3018~~~~~~~~~~~~~~~~~~~~~~ 3019 3020Before creating QinQ rule(s) the following commands should be issued to enable QinQ:: 3021 3022 testpmd> port stop 0 3023 testpmd> vlan set qinq on 0 3024 3025The above command sets the inner and outer TPID's to 0x8100. 3026 3027To change the TPID's the following commands should be used:: 3028 3029 testpmd> vlan set outer tpid 0xa100 0 3030 testpmd> vlan set inner tpid 0x9100 0 3031 testpmd> port start 0 3032 3033Validate and create a QinQ rule on port 0 to steer traffic to a VF queue in a VM. 3034 3035:: 3036 3037 testpmd> flow validate 0 ingress pattern eth / vlan tci is 123 / 3038 vlan tci is 456 / end actions vf id 1 / queue index 0 / end 3039 Flow rule #0 validated 3040 3041 testpmd> flow create 0 ingress pattern eth / vlan tci is 4 / 3042 vlan tci is 456 / end actions vf id 123 / queue index 0 / end 3043 Flow rule #0 created 3044 3045 testpmd> flow list 0 3046 ID Group Prio Attr Rule 3047 0 0 0 i- ETH VLAN VLAN=>VF QUEUE 3048 3049Validate and create a QinQ rule on port 0 to steer traffic to a queue on the host. 3050 3051:: 3052 3053 testpmd> flow validate 0 ingress pattern eth / vlan tci is 321 / 3054 vlan tci is 654 / end actions pf / queue index 0 / end 3055 Flow rule #1 validated 3056 3057 testpmd> flow create 0 ingress pattern eth / vlan tci is 321 / 3058 vlan tci is 654 / end actions pf / queue index 1 / end 3059 Flow rule #1 created 3060 3061 testpmd> flow list 0 3062 ID Group Prio Attr Rule 3063 0 0 0 i- ETH VLAN VLAN=>VF QUEUE 3064 1 0 0 i- ETH VLAN VLAN=>PF QUEUE 3065