1.. SPDX-License-Identifier: BSD-3-Clause 2 Copyright(c) 2010-2014 Intel Corporation. 3 4Running the Application 5======================= 6 7EAL Command-line Options 8------------------------ 9 10Please refer to :doc:`../linux_gsg/linux_eal_parameters` or 11:doc:`../freebsd_gsg/freebsd_eal_parameters` for a list of available EAL 12command-line options. 13 14 15Testpmd Command-line Options 16---------------------------- 17 18The following are the command-line options for the testpmd applications. 19They must be separated from the EAL options, shown in the previous section, with a ``--`` separator: 20 21.. code-block:: console 22 23 sudo ./testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2 24 25The commandline options are: 26 27* ``-i, --interactive`` 28 29 Run testpmd in interactive mode. 30 In this mode, the testpmd starts with a prompt that can be used to start and stop forwarding, 31 configure the application and display stats on the current packet processing session. 32 See :ref:`testpmd_runtime` for more details. 33 34 In non-interactive mode, 35 the application starts with the configuration specified on the command-line and 36 immediately enters forwarding mode. 37 38* ``-h, --help`` 39 40 Display a help message and quit. 41 42* ``-a, --auto-start`` 43 44 Start forwarding on initialization. 45 46* ``--tx-first`` 47 48 Start forwarding, after sending a burst of packets first. 49 50.. Note:: 51 52 This flag should be only used in non-interactive mode. 53 54* ``--stats-period PERIOD`` 55 56 Display statistics every PERIOD seconds, if interactive mode is disabled. 57 The default value is 0, which means that the statistics will not be displayed. 58 59* ``--nb-cores=N`` 60 61 Set the number of forwarding cores, 62 where 1 <= N <= "number of cores" or ``CONFIG_RTE_MAX_LCORE`` from the configuration file. 63 The default value is 1. 64 65* ``--nb-ports=N`` 66 67 Set the number of forwarding ports, 68 where 1 <= N <= "number of ports" on the board or ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file. 69 The default value is the number of ports on the board. 70 71* ``--coremask=0xXX`` 72 73 Set the hexadecimal bitmask of the cores running the packet forwarding test. 74 The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding. 75 76* ``--portmask=0xXX`` 77 78 Set the hexadecimal bitmask of the ports used by the packet forwarding test. 79 80* ``--numa`` 81 82 Enable NUMA-aware allocation of RX/TX rings and of RX memory buffers 83 (mbufs). [Default setting] 84 85* ``--no-numa`` 86 87 Disable NUMA-aware allocation of RX/TX rings and of RX memory buffers (mbufs). 88 89* ``--port-numa-config=(port,socket)[,(port,socket)]`` 90 91 Specify the socket on which the memory pool to be used by the port will be allocated. 92 93* ``--ring-numa-config=(port,flag,socket)[,(port,flag,socket)]`` 94 95 Specify the socket on which the TX/RX rings for the port will be allocated. 96 Where flag is 1 for RX, 2 for TX, and 3 for RX and TX. 97 98* ``--socket-num=N`` 99 100 Set the socket from which all memory is allocated in NUMA mode, 101 where 0 <= N < number of sockets on the board. 102 103* ``--mbuf-size=N`` 104 105 Set the data size of the mbufs used to N bytes, where N < 65536. The default value is 2048. 106 107* ``--total-num-mbufs=N`` 108 109 Set the number of mbufs to be allocated in the mbuf pools, where N > 1024. 110 111* ``--max-pkt-len=N`` 112 113 Set the maximum packet size to N bytes, where N >= 64. The default value is 1518. 114 115* ``--eth-peers-configfile=name`` 116 117 Use a configuration file containing the Ethernet addresses of the peer ports. 118 The configuration file should contain the Ethernet addresses on separate lines:: 119 120 XX:XX:XX:XX:XX:01 121 XX:XX:XX:XX:XX:02 122 ... 123 124 125* ``--eth-peer=N,XX:XX:XX:XX:XX:XX`` 126 127 Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N, 128 where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file. 129 130* ``--pkt-filter-mode=mode`` 131 132 Set Flow Director mode where mode is either ``none`` (the default), ``signature`` or ``perfect``. 133 See :ref:`testpmd_flow_director` for more details. 134 135* ``--pkt-filter-report-hash=mode`` 136 137 Set Flow Director hash match reporting mode where mode is ``none``, ``match`` (the default) or ``always``. 138 139* ``--pkt-filter-size=N`` 140 141 Set Flow Director allocated memory size, where N is 64K, 128K or 256K. 142 Sizes are in kilobytes. The default is 64. 143 144* ``--pkt-filter-flexbytes-offset=N`` 145 146 Set the flexbytes offset. 147 The offset is defined in words (not bytes) counted from the first byte of the destination Ethernet MAC address, 148 where N is 0 <= N <= 32. 149 The default value is 0x6. 150 151* ``--pkt-filter-drop-queue=N`` 152 153 Set the drop-queue. 154 In perfect filter mode, when a rule is added with queue = -1, the packet will be enqueued into the RX drop-queue. 155 If the drop-queue does not exist, the packet is dropped. The default value is N=127. 156 157* ``--disable-crc-strip`` 158 159 Disable hardware CRC stripping. 160 161* ``--enable-lro`` 162 163 Enable large receive offload. 164 165* ``--enable-rx-cksum`` 166 167 Enable hardware RX checksum offload. 168 169* ``--enable-scatter`` 170 171 Enable scatter (multi-segment) RX. 172 173* ``--enable-hw-vlan`` 174 175 Enable hardware VLAN. 176 177* ``--enable-hw-vlan-filter`` 178 179 Enable hardware VLAN filter. 180 181* ``--enable-hw-vlan-strip`` 182 183 Enable hardware VLAN strip. 184 185* ``--enable-hw-vlan-extend`` 186 187 Enable hardware VLAN extend. 188 189* ``--enable-drop-en`` 190 191 Enable per-queue packet drop for packets with no descriptors. 192 193* ``--disable-rss`` 194 195 Disable RSS (Receive Side Scaling). 196 197* ``--port-topology=mode`` 198 199 Set port topology, where mode is ``paired`` (the default) or ``chained``. 200 201 In ``paired`` mode, the forwarding is between pairs of ports, for example: (0,1), (2,3), (4,5). 202 203 In ``chained`` mode, the forwarding is to the next available port in the port mask, for example: (0,1), (1,2), (2,0). 204 205 The ordering of the ports can be changed using the portlist testpmd runtime function. 206 207* ``--forward-mode=mode`` 208 209 Set the forwarding mode where ``mode`` is one of the following:: 210 211 io (the default) 212 mac 213 macswap 214 flowgen 215 rxonly 216 txonly 217 csum 218 icmpecho 219 ieee1588 220 tm 221 noisy 222 223* ``--rss-ip`` 224 225 Set RSS functions for IPv4/IPv6 only. 226 227* ``--rss-udp`` 228 229 Set RSS functions for IPv4/IPv6 and UDP. 230 231* ``--rxq=N`` 232 233 Set the number of RX queues per port to N, where 1 <= N <= 65535. 234 The default value is 1. 235 236* ``--rxd=N`` 237 238 Set the number of descriptors in the RX rings to N, where N > 0. 239 The default value is 128. 240 241* ``--txq=N`` 242 243 Set the number of TX queues per port to N, where 1 <= N <= 65535. 244 The default value is 1. 245 246* ``--txd=N`` 247 248 Set the number of descriptors in the TX rings to N, where N > 0. 249 The default value is 512. 250 251* ``--burst=N`` 252 253 Set the number of packets per burst to N, where 1 <= N <= 512. 254 The default value is 32. 255 If set to 0, driver default is used if defined. Else, if driver 256 default is not defined, default of 32 is used. 257 258* ``--mbcache=N`` 259 260 Set the cache of mbuf memory pools to N, where 0 <= N <= 512. 261 The default value is 16. 262 263* ``--rxpt=N`` 264 265 Set the prefetch threshold register of RX rings to N, where N >= 0. 266 The default value is 8. 267 268* ``--rxht=N`` 269 270 Set the host threshold register of RX rings to N, where N >= 0. 271 The default value is 8. 272 273* ``--rxfreet=N`` 274 275 Set the free threshold of RX descriptors to N, where 0 <= N < value of --rxd. 276 The default value is 0. 277 278* ``--rxwt=N`` 279 280 Set the write-back threshold register of RX rings to N, where N >= 0. 281 The default value is 4. 282 283* ``--txpt=N`` 284 285 Set the prefetch threshold register of TX rings to N, where N >= 0. 286 The default value is 36. 287 288* ``--txht=N`` 289 290 Set the host threshold register of TX rings to N, where N >= 0. 291 The default value is 0. 292 293* ``--txwt=N`` 294 295 Set the write-back threshold register of TX rings to N, where N >= 0. 296 The default value is 0. 297 298* ``--txfreet=N`` 299 300 Set the transmit free threshold of TX rings to N, where 0 <= N <= value of ``--txd``. 301 The default value is 0. 302 303* ``--txrst=N`` 304 305 Set the transmit RS bit threshold of TX rings to N, where 0 <= N <= value of ``--txd``. 306 The default value is 0. 307 308* ``--rx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]`` 309 310 Set the RX queues statistics counters mapping 0 <= mapping <= 15. 311 312* ``--tx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]`` 313 314 Set the TX queues statistics counters mapping 0 <= mapping <= 15. 315 316* ``--no-flush-rx`` 317 318 Don't flush the RX streams before starting forwarding. Used mainly with the PCAP PMD. 319 320* ``--txpkts=X[,Y]`` 321 322 Set TX segment sizes or total packet length. Valid for ``tx-only`` 323 and ``flowgen`` forwarding modes. 324 325* ``--disable-link-check`` 326 327 Disable check on link status when starting/stopping ports. 328 329* ``--no-lsc-interrupt`` 330 331 Disable LSC interrupts for all ports, even those supporting it. 332 333* ``--no-rmv-interrupt`` 334 335 Disable RMV interrupts for all ports, even those supporting it. 336 337* ``--bitrate-stats=N`` 338 339 Set the logical core N to perform bitrate calculation. 340 341* ``--print-event <unknown|intr_lsc|queue_state|intr_reset|vf_mbox|macsec|intr_rmv|dev_probed|dev_released|all>`` 342 343 Enable printing the occurrence of the designated event. Using all will 344 enable all of them. 345 346* ``--mask-event <unknown|intr_lsc|queue_state|intr_reset|vf_mbox|macsec|intr_rmv|dev_probed|dev_released|all>`` 347 348 Disable printing the occurrence of the designated event. Using all will 349 disable all of them. 350 351* ``--flow-isolate-all`` 352 353 Providing this parameter requests flow API isolated mode on all ports at 354 initialization time. It ensures all traffic is received through the 355 configured flow rules only (see flow command). 356 357 Ports that do not support this mode are automatically discarded. 358 359* ``--tx-offloads=0xXXXXXXXX`` 360 361 Set the hexadecimal bitmask of TX queue offloads. 362 The default value is 0. 363 364* ``--hot-plug`` 365 366 Enable device event monitor machenism for hotplug. 367 368* ``--vxlan-gpe-port=N`` 369 370 Set the UDP port number of tunnel VXLAN-GPE to N. 371 The default value is 4790. 372 373* ``--mlockall`` 374 375 Enable locking all memory. 376 377* ``--no-mlockall`` 378 379 Disable locking all memory. 380 381* ``--mp-alloc <native|anon|xmem|xmemhuge>`` 382 383 Select mempool allocation mode: 384 385 * native: create and populate mempool using native DPDK memory 386 * anon: create mempool using native DPDK memory, but populate using 387 anonymous memory 388 * xmem: create and populate mempool using externally and anonymously 389 allocated area 390 * xmemhuge: create and populate mempool using externally and anonymously 391 allocated hugepage area 392 393* ``--noisy-tx-sw-buffer-size`` 394 395 Set the number of maximum elements of the FIFO queue to be created 396 for buffering packets. Only available with the noisy forwarding mode. 397 The default value is 0. 398 399* ``--noisy-tx-sw-buffer-flushtime=N`` 400 401 Set the time before packets in the FIFO queue is flushed. 402 Only available with the noisy forwarding mode. The default value is 0. 403 404* ``--noisy-lkup-memory=N`` 405 406 Set the size of the noisy neighbour simulation memory buffer in MB to N. 407 Only available with the noisy forwarding mode. The default value is 0. 408 409 410* ``--noisy-lkup-num-reads=N`` 411 412 Set the number of reads to be done in noisy neighbour simulation memory buffer to N. 413 Only available with the noisy forwarding mode. The default value is 0. 414 415* ``--noisy-lkup-num-writes=N`` 416 417 Set the number of writes to be done in noisy neighbour simulation memory buffer to N. 418 Only available with the noisy forwarding mode. The default value is 0. 419 420* ``--noisy-lkup-num-reads-writes=N`` 421 422 Set the number of r/w accesses to be done in noisy neighbour simulation memory buffer to N. 423 Only available with the noisy forwarding mode. The default value is 0. 424