xref: /csrg-svn/usr.sbin/sendmail/src/READ_ME (revision 67876)

# Copyright (c) 1983 Eric P. Allman
# Copyright (c) 1988 The Regents of the University of California.
# All rights reserved.
#
# %sccs.include.redist.sh%
#
#	@(#)READ_ME	8.72 (Berkeley) 11/02/94
#

This directory contains the source files for sendmail.

For detailed instructions, please read the document ../doc/op.me:

	eqn ../doc/op.me | pic | ditroff -me

DO NOT USE MAKE to compile sendmail -- instead, use the "makesendmail"
script located in the src directory.  It will find an appropriate
Makefile, and create an appropriate obj.* subdirectory so that
multiplatform support works easily.

The Makefile is for the new (4.4BSD) Berkeley make and uses syntax
that is not recognized by older makes.  It also has assumptions
about the 4.4 file system layout built in.  See below for details
about other Makefiles.

If you are porting to a new architecture for which there is no existing
Makefile, you might start with Makefile.dist.  This works on the old
traditional make, but isn't customized for any particular architecture.

	**************************************************
	**  Read below for more details of Makefiles.	**
	**************************************************

**************************************************************************
**  IMPORTANT:  DO NOT USE OPTIMIZATION (``-O'') IF YOU ARE RUNNING	**
**  GCC 2.4.x or 2.5.x.  THERE IS A BUG IN THE GCC OPTIMIZER THAT	**
**  CAUSES SENDMAIL COMPILES TO FAIL MISERABLY.				**
**************************************************************************

Jim Wilson of Cygnus believes he has found the problem -- it will
probably be fixed in GCC 2.5.6 -- but until this is verified, be
very suspicious of gcc -O.

**************************************************************************
**  IMPORTANT:  Read the appropriate paragraphs in the section on	**
**  ``Operating System and Compile Quirks''.				**
**************************************************************************


+-----------+
| MAKEFILES |
+-----------+

By far, the easiest way to compile sendmail is to use the "makesendmail"
script.  This uses the "uname" command to figure out what architecture
you are on and selects a proper Makefile accordingly.  It also creates
a subdirectory per object format, so that multiarchitecture support is
easy.  In general this should be all you need.  However, if for some
reason this doesn't work (e.g., NeXT systems don't have the "uname"
command) you may have to set up your compile environment by hand.

The "Makefile"s in these directories are from 4.4 BSD, and hence
really only work properly if you are on a 4.4 system.  In particular,
they use new syntax that will not be recognized on old make programs,
and some of them do things like ``.include ../../Makefile.inc'' to
pick up some system defines.  If you are getting sendmail separately,
these files won't be included in the distribution, as they are
outside of the sendmail tree.

Instead, you should use one of the other Makefiles, such as
Makefile.SunOS for a SunOS system, and so forth.  These should
work with the version of make that is appropriate for that
system.  All other Makefiles are in the "src/Makefiles" subdirectory.
They use the version of make that is native for that system.  These
are the Makefiles that I use, and they have "Berkeley quirks" in them.
I can't guarantee that they will work unmodified in your environment.
In particular, Many of them include -I/usr/sww/include/db and
-L/usr/sww/lib -- these are Berkeley's locations in the ``Software
Warehouse'' for the new database libraries, described below.  You don't
have to remove these definitions if you don't have these directories,
but you may have to remove -DNEWDB from the DBMDEF definition.

Please look for an appropriate Makefile before you start trying to
compile with Makefile or Makefile.dist.

If you want to port the new Berkeley make, you can get it from
ftp.uu.net in the directory /systems/unix/bsd-sources/usr.bin/make.
Diffs and instructions for building this version of make under
SunOS 4.1.x are available on ftp.css.itd.umich.edu in
/pub/systems/sun/Net2-make.sun4.diff.Z.  Diffs and instructions
for building this version of make under IBM AIX 3.2.4 are available
on ftp.uni-stuttgart.de in /sw/src/patches/bsd-make-rus-patches.
For Ultrix, try ftp.vix.com:~ftp/pub/patches/pmake-for-ultrix.Z.
Paul Southworth <pauls@umich.edu> published a description of porting
this make in comp.unix.bsd.

The complete text of the Makefile.inc that is in the parent of the
sendmail directory is:

	#	@(#)Makefile.inc	8.1 (Berkeley) 6/6/93

	BINDIR?=	/usr/sbin


+----------------------+
| DATABASE DEFINITIONS |
+----------------------+

There are several database formats that can be used for the alias files
and for general maps.  When used for alias files they interact in an
attempt to be back compatible.

The three options are NEWDB (the new Berkeley DB package), NDBM (the
older DBM implementation -- the very old V7 implementation is no
longer supported), and NIS (Network Information Services).  Used alone
these just include the support they indicate.  [If you are using NEWDB,
get the latest version from FTP.CS.Berkeley.EDU in /ucb/4bsd/db.tar.Z
(or db.tar.gz).  DO NOT use the version from the Net2 distribution!
However, if you are on BSD/386 or 386BSD-based systems, use the one
that already exists on your system.  You may need to #define OLD_NEWDB
1 to do this.]

[NOTE WELL: it is CRITICAL that you remove ndbm.o from libdb.a and
ndbm.h from the appropriate include directories if you want to get
ndbm support.  These files OVERRIDE calls to ndbm routines -- in
particular, if you leave ndbm.h in, you can find yourself using
the new db package even if you don't define NEWDB.]

If NEWDB and NDBM are defined (but not NIS), then sendmail will read
NDBM format alias files, but the next time a newaliases is run the
format will be converted to NEWDB; that format will be used forever
more.  This is intended as a transition feature.  [Note however that
the NEWDB library also catches and maps NDBM calls; you will have to
back out this feature to get this to work.  See ``Quirks'' section
below for details.]

If all three are defined, sendmail operates as described above, and also
looks for the file /var/yp/Makefile.  If it exists, newaliases will
build BOTH the NEWDB and NDBM format alias files.  However, it will
only use the NEWDB file; the NDBM format file is used only by the
NIS subsystem.

If NDBM and NIS are defined (regardless of the definition of NEWDB
or the existance of /var/yp/Makefile), sendmail adds the special
tokens "YP_LAST_MODIFIED" and "YP_MASTER_NAME", both of which are
required if the NDBM file is to be used as an NIS map.

There is also preliminary support for NIS+ (-DNISPLUS), Hesiod
(-DHESIOD), and NetInfo (-DNETINFO).  These have not been well
tested.

All of -DNEWDB, -DNDBM, -DNIS, -DNISPLUS, -DHESIOD, and -DNETINFO are
normally defined in the DBMDEF line in the Makefile.


+---------------+
| COMPILE FLAGS |
+---------------+

Whereever possible, I try to make sendmail pull in the correct
compilation options needed to compile on various environments based on
automatically defined symbols.  Some machines don't seem to have useful
symbols availble, requiring the following compilation flags in the
Makefile:

SOLARIS		Define this if you are running Solaris 2.0 or higher.
SOLARIS_2_3	Define this if you are running Solaris 2.3 or higher.
SUNOS403	Define this if you are running SunOS 4.0.3.
NeXT		Define this if you are on a NeXT box.  (This one may
		be pre-defined for you.)  There are other hacks you
		have to make -- see below.
_AIX3		Define this if you are IBM AIX 3.x.
RISCOS		Define this if you are running RISC/os from MIPS.
IRIX		Define this if you are running IRIX from SGI.
_SCO_unix_	Define this if you are on SCO UNIX.
_SCO_unix_4_2	Define this if you are on SCO Open Server 3.2v4.
DGUX		Define this if you are on DG/UX 5.4.3 or later
DGUX_5_4_2	Define this if you are on DG/UX systems prior to 5.4.3.
NonStop_UX_BXX	Define this if you are on a Tandem NonStop-UX release
		Bxx system.

If you are a system that sendmail has already been ported to, you
probably won't have to touch these.  But if you are porting, you may
have to tweak the following compilation flags in conf.h in order to
get it to compile and link properly:

SYSTEM5		Adjust for System V (not necessarily Release 4).
SYS5SIGNALS	Use System V signal semantics -- the signal handler
		is automatically dropped when the signal is caught.
		If this is not set, use POSIX/BSD semantics, where the
		signal handler stays in force until an exec or an
		explicit delete.  Implied by SYSTEM5.
SYS5SETPGRP	Use System V setpgrp() semantics.  Implied by SYSTEM5.
HASFLOCK	Set this if you prefer to use the flock(2) system call
		rather than using fcntl-based locking.  Fcntl locking
		has some semantic gotchas, but many vendor systems
		also interface it to lockd(8) to do NFS-style locking.
		For this reason, this should not be set unless you
		don't have an alternative.
HASUNAME	Set if you have the "uname" system call.  Implied by
		SYSTEM5.
HASUNSETENV	Define this if your system library has the "unsetenv"
		subroutine.
HASSETSID	Define this if you have the setsid(2) system call.  This
		is implied if your system appears to be POSIX compliant.
HASINITGROUPS	Define this if you have the initgroups(3) routine.
HASSETVBUF	Define this if you have the setvbuf(3) library call.
		If you don't, setlinebuf will be used instead.  This
		defaults on if your compiler defines __STDC__.
HASSETREUID	Define this if you have setreuid(2) ***AND*** root can
		use setreuid to change to an arbitrary user.  This second
		condition is not satisfied on AIX 3.x.  You may find that
		your system has setresuid(2), (for example, on HP-UX) in
		which case you will also have to #define setreuid(r, e)
		to be the appropriate call.  Some systems (such as Solaris)
		have a compatibility routine that doesn't work properly,
		but may have "saved user ids" properly implemented so you
		can ``#define setreuid(r, e) seteuid(e)'' and have it work.
		The important thing is that you have a call that will set
		the effective uid independently of the real or saved uid
		and be able to set the effective uid back again when done.
		There's a test program in ../test/t_setreuid.c that will
		try things on your system.  Setting this improves the
		security, since sendmail doesn't have to read .forward
		and :include: files as root.  There are certain attacks
		that may be unpreventable without this call.
HASLSTAT	Define this if you have symbolic links (and thus the
		lstat(2) system call).  This improves security.  Unlike
		most other options, this one is on by default, so you
		need to #undef it in conf.h if you don't have symbolic
		links (these days everyone does).
HASSETRLIMIT	Define this to 1 if you have the setrlimit(2) syscall.
		You can define it to 0 to force it off.  It is assumed
		if you are running a BSD-like system.
HASULIMIT	Define this if you have the ulimit(2) syscall (System V
		style systems).  HASSETRLIMIT overrides, as it is more
		general.
NEEDGETOPT	Define this if you need a reimplementation of getopt(3).
		On some systems, getopt does very odd things if called
		to scan the arguments twice.  This flag will ask sendmail
		to compile in a local version of getopt that works
		properly.
NEEDSTRTOL	Define this if your standard C library does not define
		strtol(3).  This will compile in a local version.
NEEDVPRINTF	Define this if your standard C library does not define
		vprintf(3).  Note that the resulting fake implementation
		is not very elegant and may not even work on some
		architectures.
NEEDFSYNC	Define this if your standard C library does not define
		fsync(2).  This will try to simulate the operation using
		fcntl(2); if that is not available it does nothing, which
		isn't great, but at least it compiles and runs.
HASGETUSERSHELL	Define this to 1 if you have getusershell(3) in your
		standard C library.  If this is not defined, or is defined
		to be 0, sendmail will scan the /etc/shells file (no
		NIS-style support, defaults to /bin/sh and /bin/csh if
		that file does not exist) to get a list of unrestricted
		user shells.  This is used to determine whether users
		are allowed to forward their mail to a program or a file.
GIDSET_T	The type of entries in a gidset passed as the second
		argument to getgroups(2).  Historically this has been an
		int, so this is the default, but some systems (such as
		IRIX) pass it as a gid_t, which is an unsigned short.
		This will make a difference, so it is important to get
		this right!  However, it is only an issue if you have
		group sets.
SLEEP_T		The type returned by the system sleep() function.
		Defaults to "unsigned int".  Don't worry about this
		if you don't have compilation problems.
ARBPTR_T	The type of an arbitrary pointer -- defaults to "void *".
		If you are an very old compiler you may need to define
		this to be "char *".
LA_TYPE		The type of load average your kernel supports.  These
		can be one of:
		LA_ZERO (1) -- it always returns the load average as
			"zero" (and does so on all architectures).
		LA_SUBR (4) if you have the getloadavg(3) routine,
		LA_MACH (5) to use MACH-style load averages (calls
			processor_set_info()),
		LA_PROCSTR (7) to read /proc/loadavg and interpret it
			as a string representing a floating-point
			number (Linux-style),
		LA_FLOAT (3) if you read kmem and interpret the value
			as a floating point number,
		LA_INT (2) to interpret as a long integer,
		LA_SHORT (6) to interpret as a short integer.
		These last three have several other parameters that they
		try to divine: the name of your kernel, the name of the
		variable in the kernel to examine, the number of bits of
		precision in a fixed point load average, and so forth.
		In desperation, use LA_ZERO.  The actual code is in
		conf.c -- it can be tweaked if you are brave.
SFS_TYPE	Encodes how your kernel can locate the amount of free
		space on a disk partition.  This can be set to SFS_NONE
		(0) if you have no way of getting this information,
		SFS_USTAT (1) if you have the ustat(2) system call,
		SFS_4ARGS (2) if you have a four-argument statfs(2)
		system call (and the include file is <sys/statfs.h>),
		SFS_VFS (3), SFS_MOUNT (4), SFS_STATFS (5) if you have
		the two-argument statfs(2) system call with includes in
		<sys/vfs.h>, <sys/mount.h>, or <sys/statfs.h> respectively,
		or SFS_STATVFS (6) if you have the two-argument statvfs(2)
		call.  The default if nothing is defined is SFS_NONE.
SPT_TYPE	Encodes how your system can display what a process is doing
		on a ps(1) command (SPT stands for Set Process Title).  Can
		be set to:
		SPT_NONE (0) -- Don't try to set the process title at all.
		SPT_REUSEARGV (1) -- Pad out your argv with the information;
			this is the default if none specified.
		SPT_BUILTIN (2) -- The system library has setproctitle.
		SPT_PSTAT (3) -- Use the PSTAT_SETCMD option to pstat(2)
			to set the process title; this is used by HP-UX.
		SPT_PSSTRINGS (4) -- Use the magic PS_STRINGS pointer (4.4BSD).
SPT_PADCHAR	Character used to pad the process title; if undefined,
		the space character (0x20) is used.  This is ignored if
		SPT_TYPE != SPT_REUSEARGV
ERRLIST_PREDEFINED
		If set, assumes that some header file defines sys_errlist.
		This may be needed if you get type conflicts on this
		variable -- otherwise don't worry about it.
WAITUNION	The wait(2) routine takes a "union wait" argument instead
		of an integer argument.  This is for compatibility with
		old versions of BSD.
SCANF		You can set this to extend the F command to accept a
		scanf string -- this gives you a primitive parser for
		class definitions -- BUT it can make you vulnerable to
		core dumps if the target file is poorly formed.
SYSLOG_BUFSIZE	You can define this to be the size of the buffer that
		syslog accepts.  If it is not defined, it assumes a
		1024-byte buffer.  If the buffer is very small (under
		256 bytes) the log message format changes -- each
		e-mail message will log many more messages, since it
		will log each piece of information as a separate line
		in syslog.
BROKEN_RES_SEARCH
		On Ultrix (and maybe other systems?) if you use the
		res_search routine with an unknown host name, it returns
		-1 but sets h_errno to 0 instead of HOST_NOT_FOUND.  If
		you set this, sendmail considers 0 to be the same as
		HOST_NOT_FOUND.
NAMELISTMASK	If defined, values returned by nlist(3) are masked
		against this value before use -- a common value is
		0x7fffffff to strip off the top bit.



+-----------------------+
| COMPILE-TIME FEATURES |
+-----------------------+

There are a bunch of features that you can decide to compile in, such
as selecting various database packages and special protocol support.
Several are assumed based on other compilation flags -- if you want to
"un-assume" something, you probably need to edit conf.h.  Compilation
flags that add support for special features include:

NDBM		Include support for "new" DBM library for aliases and maps.
		Normally defined in the Makefile.
NEWDB		Include support for Berkeley "db" package (hash & btree)
		for aliases and maps.  Normally defined in the Makefile.
OLD_NEWDB	If non-zero, the version of NEWDB you have is the old
		one that does not include the "fd" call.  This call was
		added in version 1.5 of the Berkeley DB code.  If you
		use -DOLD_NEWDB=0 it forces you to use the new interface.
NIS		Define this to get NIS (YP) support for aliases and maps.
		Normally defined in the Makefile.
USERDB		Include support for the User Information Database.  Implied
		by NEWDB in conf.h.
IDENTPROTO	Define this as 1 to get IDENT (RFC 1413) protocol support.
		This is assumed unless you are running on Ultrix or
		HP-UX, both of which have a problem in the UDP
		implementation.  You can define it to be 0 to explicitly
		turn off IDENT protocol support.
MIME		Include support for MIME-encapsulated error messages.
LOG		Set this to get syslog(3) support.  Defined by default
		in conf.h.  You want this if at all possible.
NETINET		Set this to get TCP/IP support.  Defined by default
		in conf.h.  You probably want this.
NETISO		Define this to get ISO networking support.
SMTP		Define this to get the SMTP code.  Implied by NETINET
		or NETISO.
NAMED_BIND	Define this to get DNS (name daemon) support, including
		MX support.  The specs you must use this if you run
		SMTP.  Defined by default in conf.h.
QUEUE		Define this to get queueing code.  Implied by NETINET
		or NETISO; required by SMTP.  This gives you other good
		stuff -- it should be on.
DAEMON		Define this to get general network support.  Implied by
		NETINET or NETISO.  Defined by default in conf.h.  You
		almost certainly want it on.
MATCHGECOS	Permit fuzzy matching of user names against the full
		name (GECOS) field in the /etc/passwd file.  This should
		probably be on, since you can disable it from the config
		file if you want to.  Defined by default in conf.h.


+---------------------+
| DNS/RESOLVER ISSUES |
+---------------------+

Many systems have old versions of the resolver library.  At a minimum,
you should be running BIND 4.8.3; older versions may compile, but they
have known bugs that should give you pause.

Common problems in old versions include "undefined" errors for
dn_skipname.

Some people have had a problem with BIND 4.9; it uses some routines
that it expects to be externally defined such as strerror().  It may
help to link with "-l44bsd" to solve this problem.

!PLEASE! be sure to link with the same version of the resolver as
the header files you used -- some people have used the 4.9 headers
and linked with BIND 4.8 or vice versa, and it doesn't work.
Unfortunately, it doesn't fail in an obvious way -- things just
subtly don't work.


+-------------------------------------+
| OPERATING SYSTEM AND COMPILE QUIRKS |
+-------------------------------------+

GCC 2.5.x problems  *** IMPORTANT ***
	Date: Mon, 29 Nov 93 19:08:44 PST
	From: wilson@cygnus.com (Jim Wilson)
	Message-Id: <9311300308.AA04608@cygnus.com>
	To: kenner@vlsi1.ultra.nyu.edu
	Subject: [cattelan@thebarn.com: gcc 2.5.4-2.5.5 -O bug]
	Cc: cattelan@thebarn.com, rms@gnu.ai.mit.edu, sendmail@cs.berkeley.edu

	This fixes a problem that occurs when gcc 2.5.5 is used to compile
	sendmail 8.6.4 with optimization on a sparc.

	Mon Nov 29 19:00:14 1993  Jim Wilson  (wilson@sphagnum.cygnus.com)

		* reload.c (find_reloads_toplev): Replace obsolete reference to
		BYTE_LOADS_*_EXTEND with LOAD_EXTEND_OP.

	*** clean-ss-931128/reload.c    Sun Nov 14 16:20:01 1993
	--- ss-931128/reload.c  Mon Nov 29 18:52:55 1993
	*************** find_reloads_toplev (x, opnum, type, ind
	*** 3888,3894 ****
		 force a reload in that case.  So we should not do anything here.  */

		else if (regno >= FIRST_PSEUDO_REGISTER
	! #if defined(BYTE_LOADS_ZERO_EXTEND) || defined(BYTE_LOADS_SIGN_EXTEND)
		       && (GET_MODE_SIZE (GET_MODE (x))
			   <= GET_MODE_SIZE (GET_MODE (SUBREG_REG (x))))
	  #endif
	--- 3888,3894 ----
		 force a reload in that case.  So we should not do anything here.  */

		else if (regno >= FIRST_PSEUDO_REGISTER
	! #ifdef LOAD_EXTEND_OP
		       && (GET_MODE_SIZE (GET_MODE (x))
			   <= GET_MODE_SIZE (GET_MODE (SUBREG_REG (x))))
	  #endif


SunOS 4.x (Solaris 1.x)
	You may have to use -lresolv on SunOS.  However, beware that
	this links in a new version of gethostbyname that does not
	understand NIS, so you must have all of your hosts in DNS.

	Some people have reported problems with the SunOS version of
	-lresolv and/or in.named, and suggest that you get a newer
	version.  The symptoms are delays when you connect to the
	SMTP server on a SunOS machine or having your domain added to
	addresses inappropriately.  There is a version of BIND
	version 4.9 on gatekeeper.DEC.COM in pub/BSD/bind/4.9.

	There is substantial disagreement about whether you can make
	this work with resolv+, which allows you to specify a search-path
	of services.  Some people report that it works fine, others
	claim it doesn't work at all (including causing sendmail to
	drop core when it tries to do multiple resolv+ lookups for a
	single job).  I haven't tried resolv+, as we use DNS exclusively.

	Should you want to try resolv+, it is on ftp.uu.net in
	/networking/ip/dns.

	Apparently getservbyname() can fail under moderate to high
	load under some circumstances.  This will exhibit itself as
	the message ``554 makeconnection: service "smtp" unknown''.
	The problem has been traced to one or more blank lines in
	/etc/services on the NIS server machine.  Delete these
	and it should work.  This info is thanks to Brian Bartholomew
	<bb@math.ufl.edu> of I-Kinetics, Inc.

Solaris 2.x (SunOS 5.x)
	To compile for Solaris, be sure you use -DSOLARIS.

	To the best of my knowledge, Solaris does not have the
	gethostbyname problem described above.  However, it does
	have another one:

	From a correspondent:

	   For solaris 2.2, I have

		hosts:      files dns

	   in /etc/nsswitch.conf and /etc/hosts has to have the fully
	   qualified host name. I think "files" has to be before "dns"
	   in /etc/nsswitch.conf during bootup.

	From another correspondent:

	   When running sendmail under Solaris, the gethostbyname()
	   hack in conf.c which should perform proper canonicalization
	   of host names could fail.  Result: the host name is not
	   canonicalized despite the hack, and you'll have to define $j
	   and $m in sendmail.cf somewhere.

	   The reason could be that /etc/nsswitch.conf is improperly
	   configured (at least from sendmail's point of view).  For
	   example, the line

		hosts:      files nisplus dns

	   will make gethostbyname() look in /etc/hosts first, then ask
	   nisplus, then dns.  However, if /etc/hosts does not contain
	   the full canonicalized hostname, then no amount of
	   gethostbyname()s will work.

	   Solution (or rather, a workaround): Ask nisplus first, then
	   dns, then local files:

		hosts:      nisplus dns [NOTFOUND=return] files

	The Solaris "syslog" function is apparently limited to something
	about 90 characters because of a kernel limitation.  If you have
	source code, you can probably up this number.  You can get patches
	that fix this problem: the patch ids are:

		Solaris 2.1	100834
		Solaris 2.2	100999
		Solaris 2.3	101318

	Be sure you have the appropriate patch installed or you won't
	see system logging.

OSF/1
	If you are compiling on OSF/1 (DEC Alpha), you must use
	-L/usr/shlib (otherwise it core dumps on startup).  You may also
	need -mld to get the nlist() function, although some versions
	apparently don't need this.

	Also, the enclosed makefile removed /usr/sbin/smtpd; if you need
	it, just create the link to the sendmail binary.

IRIX
	The header files on SGI IRIX are completely prototyped, and as
	a result you can sometimes get some warning messages during
	compilation.  These can be ignored.  There are two errors in
	deliver only if you are using gcc, both of the form ``warning:
	passing arg N of `execve' from incompatible pointer type''.
	Also, if you compile with -DNIS, you will get a complaint
	about a declaration of struct dom_binding in a prototype
	when compiling map.c; this is not important because the
	function being prototyped is not used in that file.

	In order to compile sendmail you will have had to install
	the developers' option in order to get the necessary include
	files.

NeXT
	If you are compiling on NeXT, you will have to create an empty
	file "unistd.h" and create a file "dirent.h" containing:

		#include <sys/dir.h>
		#define dirent	direct

	(The Makefile.NeXT should try to do both of these for you.)

	Apparently, there is a bug in getservbyname on Nextstep 3.0
	that causes it to fail under some circumstances with the
	message "SYSERR: service "smtp" unknown" logged.  You should
	be able to work around this by including the line:

		OOPort=25

	in your .cf file.

	You may have to use -DNeXT.

BSDI (BSD/386) 1.0, NetBSD 0.9, FreeBSD 1.0
	The "m4" from BSDI won't handle the config files properly.
	I haven't had a chance to test this myself.

	The M4 shipped in FreeBSD and NetBSD 0.9 don't handle the config
	files properly. One must use either GNU m4 1.1 or the PD-M4
	recently posted in comp.os.386bsd.bugs (and maybe others).
	NetBSD-current includes the PD-M4 (as stated in the NetBSD file
	CHANGES).

	FreeBSD 1.0 RELEASE has uname(2) now. Use -DUSEUNAME in order to
	use it (look into Makefile.FreeBSD). NetBSD-current may have
	it too but it has not been verified.

	You cannot port the latest version of the Berkeley db library
	and use it with sendmail without recompiling the world.  This
	is because C library routines use the older version which have
	incompatible header files -- the result is that it can't read
	other system files, such as /etc/passwd, unless you use the
	new db format throughout your system.  You should normally just
	use the version of db supplied in your release.  You may need
	to use -DOLD_NEWDB=1 to make this work -- this turns off some
	new interface calls (for file locking) that are not in older
	versions of db.  You'll get compile errors if you need this
	flag and don't have it set.

4.3BSD
	If you are running a "virgin" version of 4.3BSD, you'll have
	a very old resolver and be missing some header files.  The
	header files are simple -- create empty versions and everything
	will work fine.  For the resolver you should really port a new
	version (4.8.3 or later) of the resolver; 4.9 is available on
	gatekeeper.DEC.COM in pub/BSD/bind/4.9.  If you are really
	determined to continue to use your old, buggy version (or as
	a shortcut to get sendmail working -- I'm sure you have the
	best intentions to port a modern version of BIND), you can
	copy ../contrib/oldbind.compat.c into src and add
	oldbind.compat.o to OBJADD in the Makefile.

A/UX
	Date: Tue, 12 Oct 1993 18:28:28 -0400 (EDT)
	From: "Eric C. Hagberg" <hagberg@med.cornell.edu>
	Subject: Fix for A/UX ndbm

	I guess this isn't really a sendmail bug, however, it is something
	that A/UX users should be aware of when compiling sendmail 8.6.

	Apparently, the calls that sendmail is using to the ndbm routines
	in A/UX 3.0.x contain calls to "broken" routines, in that the
	aliases database will break when it gets "just a little big"
	(sorry I don't have exact numbers here, but it broke somewhere
	around 20-25 aliases for me.), making all aliases non-functional
	after exceeding this point.

	What I did was to get the gnu-dbm-1.6 package, compile it, and
	then re-compile sendmail with "-lgdbm", "-DNDBM", and using the
	ndbm.h header file that comes with the gnu-package. This makes
	things behave properly.

	I suppose porting the New Berkeley db package is another route,
	however, I made a quick attempt at it, and found it difficult
	(not easy at least); the gnu-dbm package "configured" and
	compiled easily.

DG/UX
	Apparently, /bin/mail doesn't work properly for delivery on
	DG/UX -- the person who has this working, Douglas Anderson
	<dlander@afterlife.ncsc.mil>, used procmail instead.  The
	problem is that DG/UX /bin/mail requires that an environment
	variable be set (_FORCE_MAIL_LOCAL_=yes); sendmail has no
	mechanism for this.  Several people report that procmail works
	beautifully.

Apollo DomainOS
	If you are compiling on Apollo, you will have to create an empty
	file "unistd.h" and create a file "dirent.h" containing:

		#include <sys/dir.h>
		#define dirent	direct

	(The Makefile.DomainOS will attempt to do both of these for you.)

HP-UX 8.00
	Date: Mon, 24 Jan 1994 13:25:45 +0200
	From: Kimmo Suominen <Kimmo.Suominen@lut.fi>
	Subject: 8.6.5 w/ HP-UX 8.00 on s300

	Just compiled and fought with sendmail 8.6.5 on a HP9000/360 (ie. a
	series 300 machine) running HP-UX 8.00.

	I was getting segmentation fault when delivering to a local user.
	With debugging I saw it was faulting when doing _free@libc... *sigh*
	It seems the new implementation of malloc on s300 is buggy as of 8.0,
	so I tried out the one in -lmalloc (malloc(3X)).  With that it seems
	to work just dandy.

	When linking, you will get the following error:

	ld: multiply defined symbol _freespace in file /usr/lib/libmalloc.a

	but you can just ignore it.  You might want to add this info to the
	README file for the future...

Linux
	Something broke between versions 0.99.13 and 0.99.14 of Linux:
	the flock() system call gives errors.  If you are running .14,
	you must not use flock.  You can do this with -DHASFLOCK=0.

AIX
	This version of sendmail does not support MB, MG, and MR resource
	records, which are supported by AIX sendmail.

RISC/os
	RISC/os from MIPS is a merged AT&T/Berkeley system.  When you
	compile on that platform you will get duplicate definitions
	on many files.  You can ignore these.

System V Release 4 Based Systems
	There is a single Makefile that is intended for all SVR4-based
	systems (called Makefile.SVR4).  It defines __svr4__, which is
	predefined by some compilers.  If your compiler already defines
	this compile variable, you can delete the definition from the
	Makefile.

	It's been tested on Dell Issue 2.2.

DELL SVR4
	Date:      Mon, 06 Dec 1993 10:42:29 EST
	From: "Kimmo Suominen" <kim@grendel.lut.fi>
	Message-ID: <2d0352f9.lento29@lento29.UUCP>
	To: eric@cs.berkeley.edu
	Cc: sendmail@cs.berkeley.edu
	Subject:   Notes for DELL SVR4

	Eric,

	Here are some notes for compiling Sendmail 8.6.4 on DELL SVR4.  I ran
	across these things when helping out some people who contacted me by
	e-mail.

	1) Use gcc 2.4.5 (or later?).  Dell distributes gcc 2.1 with their
	   Issue 2.2 Unix.  It is too old, and gives you problems with
	   clock.c, because sigset_t won't get defined in <sys/signal.h>.
	   This is due to a problematic protection rule in there, and is
	   fixed with gcc 2.4.5.

	2) If you don't use the new Berkeley DB (-DNEWDB), then you need
	   to add "-lc -lucb" to the libraries to link with.  This is because
	   the -ldbm distributed by Dell needs the bcopy, bcmp and bzero
	   functions.  It is important that you specify both libraries in
	   the given order to be sure you only get the BSTRING functions
	   from the UCB library (and not the signal routines etc.).

	3) Don't leave out "-lelf" even if compiling with "-lc -lucb".
	   The UCB library also has another copy of the nlist routines,
	   but we do want the ones from "-lelf".

	If anyone needs a compiled gcc 2.4.5 and/or a ported DB library, they
	can use anonymous ftp to fetch them from lut.fi in the /kim directory.
	They are copies of what I use on grendel.lut.fi, and offering them
	does not imply that I would also support them.  I have sent the DB
	port for SVR4 back to Keith Bostic for inclusion in the official
	distribution, but I haven't heard anything from him as of today.

	- gcc-2.4.5-svr4.tar.gz	(gcc 2.4.5 and the corresponding libg++)
	- db-1.72.tar.gz	(with source, objects and a installed copy)

	Cheers
	+ Kim
	--
	 *  Kimmo.Suominen@lut.fi  *  SysVr4 enthusiast at GRENDEL.LUT.FI  *
	*    KIM@FINFILES.BITNET   *  Postmaster and Hostmaster at LUT.FI   *
	 *    + 358 200 865 718    *  Unix area moderator at NIC.FUNET.FI  *

ConvexOS 10.1 and below
	In order to use the name server, you must create the file
	/etc/use_nameserver.  If this file does not exist, the call
	to res_init() will fail and you will have absolutely no
	access to DNS, including MX records.

Non-DNS based sites
	This version of sendmail always tries to connect to the Domain
	Name System (DNS) to resolve names, regardless of the setting
	of the `I' option.  On most systems that are not running DNS,
	this will fail quickly and sendmail will continue, but on some
	systems it has a long timeout.  If you have this problem, you
	will have to recompile without NAMED_BIND.  Some people have
	claimed that they have successfully used "OI+USEVC" to force
	sendmail to use a virtual circuit -- this will always time out
	quickly, but also tells sendmail that a failed connection
	should requeue the message (probably not what you intended).
	A future release of sendmail will correct this problem.

Both NEWDB and NDBM
	If you use both -DNDBM and -DNEWDB, you must delete the module
	ndbm.o from libdb.a and delete the file "ndbm.h" from the files
	that get installed (that is, use the OLD ndbm.h, not the new
	ndbm.h).  This compatibility module maps ndbm calls into DB
	calls, and breaks things rather badly.

GNU getopt
	I'm told that GNU getopt has a problem in that it gets confused
	by the double call.  Use the version in conf.c instead.

BIND 4.9.2 and Ultrix
	If you are running on Ultrix, be sure you read conf/Info.Ultrix
	in the BIND distribution very carefully -- there is information
	in there that you need to know in order to avoid errors of the
	form:

		/lib/libc.a(gethostent.o): sethostent: multiply defined
		/lib/libc.a(gethostent.o): endhostent: multiply defined
		/lib/libc.a(gethostent.o): gethostbyname: multiply defined
		/lib/libc.a(gethostent.o): gethostbyaddr: multiply defined

	during the link stage.


+--------------+
| MANUAL PAGES |
+--------------+

The manual pages have been written against the -mandoc macros
instead of the -man macros.  The latest version of groff has them
included.  You can also get a copy from FTP.UU.NET in directory
/systems/unix/bsd-sources/share/tmac.


+-----------------+
| DEBUGGING HOOKS |
+-----------------+

As of 8.6.5, sendmail daemons will catch a SIGUSR1 signal and log
some debugging output (logged at LOG_DEBUG severity).  The
information dumped is:

 * The value of the $j macro.
 * A warning if $j is not in the set $=w.
 * A list of the open file descriptors.
 * The contents of the connection cache.
 * If ruleset 89 is defined, it is evaluated and the results printed.

This allows you to get information regarding the runtime state of the
daemon on the fly.  This should not be done too frequently, since
the process of rewriting may lose memory which will not be recovered.
Also, ruleset 89 may call non-reentrant routines, so there is a small
non-zero probability that this will cause other problems.  It is
really only for debugging serious problems.

A typical formulation of ruleset 89 would be:

	R$*		$@ $>0 some test address


+-----------------------------+
| DESCRIPTION OF SOURCE FILES |
+-----------------------------+

The following list describes the files in this directory:

Makefile	The makefile used here; this version only works with
		the new Berkeley make.
Makefile.dist	A trimmed down version of the makefile that works with
		the old make.
READ_ME		This file.
TRACEFLAGS	My own personal list of the trace flags -- not guaranteed
		to be particularly up to date.
alias.c		Does name aliasing in all forms.
arpadate.c	A subroutine which creates ARPANET standard dates.
clock.c		Routines to implement real-time oriented functions
		in sendmail -- e.g., timeouts.
collect.c	The routine that actually reads the mail into a temp
		file.  It also does a certain amount of parsing of
		the header, etc.
conf.c		The configuration file.  This contains information
		that is presumed to be quite static and non-
		controversial, or code compiled in for efficiency
		reasons.  Most of the configuration is in sendmail.cf.
conf.h		Configuration that must be known everywhere.
convtime.c	A routine to sanely process times.
daemon.c	Routines to implement daemon mode.  This version is
		specifically for Berkeley 4.1 IPC.
deliver.c	Routines to deliver mail.
domain.c	Routines that interface with DNS (the Domain Name
		System).
err.c		Routines to print error messages.
envelope.c	Routines to manipulate the envelope structure.
headers.c	Routines to process message headers.
macro.c		The macro expander.  This is used internally to
		insert information from the configuration file.
main.c		The main routine to sendmail.  This file also
		contains some miscellaneous routines.
map.c		Support for database maps.
mci.c		Routines that handle mail connection information caching.
parseaddr.c	The routines which do address parsing.
queue.c		Routines to implement message queueing.
readcf.c	The routine that reads the configuration file and
		translates it to internal form.
recipient.c	Routines that manipulate the recipient list.
savemail.c	Routines which save the letter on processing errors.
sendmail.h	Main header file for sendmail.
srvrsmtp.c	Routines to implement server SMTP.
stab.c		Routines to manage the symbol table.
stats.c		Routines to collect and post the statistics.
sysexits.c	List of error messages associated with error codes
		in sysexits.h.
trace.c		The trace package.  These routines allow setting and
		testing of trace flags with a high granularity.
udb.c		The user database interface module.
usersmtp.c	Routines to implement user SMTP.
util.c		Some general purpose routines used by sendmail.
version.c	The version number and information about this
		version of sendmail.  Theoretically, this gets
		modified on every change.

Eric Allman

(Version 8.72, last update 11/02/94 14:13:06)