xref: /csrg-svn/sys/hp300/include/cpu.h (revision 69530)

/*
 * Copyright (c) 1988 University of Utah.
 * Copyright (c) 1982, 1990, 1993
 *	The Regents of the University of California.  All rights reserved.
 *
 * This code is derived from software contributed to Berkeley by
 * the Systems Programming Group of the University of Utah Computer
 * Science Department.
 *
 * %sccs.include.redist.c%
 *
 * from: Utah $Hdr: cpu.h 1.16 91/03/25$
 *
 *	@(#)cpu.h	8.5 (Berkeley) 05/17/95
 */

/*
 * Exported definitions unique to hp300/68k cpu support.
 */

/*
 * definitions of cpu-dependent requirements
 * referenced in generic code
 */
#define	COPY_SIGCODE		/* copy sigcode above user stack in exec */

#define	cpu_exec(p)			/* nothing */
#define	cpu_swapin(p)			/* nothing */
#define	cpu_wait(p)			/* nothing */
#define cpu_setstack(p, ap)		(p)->p_md.md_regs[SP] = ap
#define cpu_set_init_frame(p, fp)	(p)->p_md.md_regs = fp
#define BACKTRACE(p)			backtrace(p)

/*
 * Arguments to hardclock and gatherstats encapsulate the previous
 * machine state in an opaque clockframe.  One the hp300, we use
 * what the hardware pushes on an interrupt (frame format 0).
 */
struct clockframe {
	u_short	sr;		/* sr at time of interrupt */
	u_long	pc;		/* pc at time of interrupt */
	u_short	vo;		/* vector offset (4-word frame) */
};

#define	CLKF_USERMODE(framep)	(((framep)->sr & PSL_S) == 0)
#define	CLKF_BASEPRI(framep)	(((framep)->sr & PSL_IPL) == 0)
#define	CLKF_PC(framep)		((framep)->pc)
#if 0
/* We would like to do it this way... */
#define	CLKF_INTR(framep)	(((framep)->sr & PSL_M) == 0)
#else
/* but until we start using PSL_M, we have to do this instead */
#define	CLKF_INTR(framep)	(0)	/* XXX */
#endif


/*
 * Preempt the current process if in interrupt from user mode,
 * or after the current trap/syscall if in system mode.
 */
#define	need_resched()	{ want_resched++; aston(); }

/*
 * Give a profiling tick to the current process when the user profiling
 * buffer pages are invalid.  On the hp300, request an ast to send us
 * through trap, marking the proc as needing a profiling tick.
 */
#define	need_proftick(p)	{ (p)->p_flag |= P_OWEUPC; aston(); }

/*
 * Notify the current process (p) that it has a signal pending,
 * process as soon as possible.
 */
#define	signotify(p)	aston()

#define aston() (astpending++)

int	astpending;		/* need to trap before returning to user mode */
int	want_resched;		/* resched() was called */


/*
 * simulated software interrupt register
 */
extern unsigned char ssir;

#define SIR_NET		0x1
#define SIR_CLOCK	0x2

#define siroff(x)	ssir &= ~(x)
#define setsoftnet()	ssir |= SIR_NET
#define setsoftclock()	ssir |= SIR_CLOCK

/*
 * CTL_MACHDEP definitions.
 */
#define	CPU_CONSDEV		1	/* dev_t: console terminal device */
#define	CPU_MAXID		2	/* number of valid machdep ids */

#define CTL_MACHDEP_NAMES { \
	{ 0, 0 }, \
	{ "console_device", CTLTYPE_STRUCT }, \
}

/*
 * The rest of this should probably be moved to ../hp300/hp300cpu.h,
 * although some of it could probably be put into generic 68k headers.
 */

/* values for machineid */
#define	HP_320		0	/* 16Mhz 68020+HP MMU+16K external cache */
#define	HP_330		1	/* 16Mhz 68020+68851 MMU */
#define	HP_350		2	/* 25Mhz 68020+HP MMU+32K external cache */
#define	HP_360		3	/* 25Mhz 68030 */
#define	HP_370		4	/* 33Mhz 68030+64K external cache */
#define	HP_340		5	/* 16Mhz 68030 */
#define	HP_375		6	/* 50Mhz 68030+32K external cache */
#define	HP_380		7	/* 25Mhz 68040 */
#define HP_433		8	/* 33Mhz 68040 */

/* values for mmutype (assigned for quick testing) */
#define	MMU_68040	-2	/* 68040 on-chip MMU */
#define	MMU_68030	-1	/* 68030 on-chip subset of 68851 */
#define	MMU_HP		0	/* HP proprietary */
#define	MMU_68851	1	/* Motorola 68851 */

/* values for ectype */
#define	EC_PHYS		-1	/* external physical address cache */
#define	EC_NONE		0	/* no external cache */
#define	EC_VIRT		1	/* external virtual address cache */

/* values for cpuspeed (not really related to clock speed due to caches) */
#define	MHZ_8		1
#define	MHZ_16		2
#define	MHZ_25		3
#define	MHZ_33		4
#define	MHZ_50		6

#ifdef KERNEL
extern	int machineid, mmutype, ectype;
extern	char *intiobase, *intiolimit;

/* what is this supposed to do? i.e. how is it different than startrtclock? */
#define	enablertclock()

#endif

/* physical memory sections */
#define	ROMBASE		(0x00000000)
#define	INTIOBASE	(0x00400000)
#define	INTIOTOP	(0x00600000)
#define	EXTIOBASE	(0x00600000)
#define	EXTIOTOP	(0x20000000)
#define	MAXADDR		(0xFFFFF000)

/*
 * Internal IO space:
 *
 * Ranges from 0x400000 to 0x600000 (IIOMAPSIZE).
 *
 * Internal IO space is mapped in the kernel from ``intiobase'' to
 * ``intiolimit'' (defined in locore.s).  Since it is always mapped,
 * conversion between physical and kernel virtual addresses is easy.
 */
#define	ISIIOVA(va) \
	((char *)(va) >= intiobase && (char *)(va) < intiolimit)
#define	IIOV(pa)	((int)(pa)-INTIOBASE+(int)intiobase)
#define	IIOP(va)	((int)(va)-(int)intiobase+INTIOBASE)
#define	IIOPOFF(pa)	((int)(pa)-INTIOBASE)
#define	IIOMAPSIZE	btoc(INTIOTOP-INTIOBASE)	/* 2mb */

/*
 * External IO space:
 *
 * DIO ranges from select codes 0-63 at physical addresses given by:
 *	0x600000 + (sc - 32) * 0x10000
 * DIO cards are addressed in the range 0-31 [0x600000-0x800000) for
 * their control space and the remaining areas, [0x200000-0x400000) and
 * [0x800000-0x1000000), are for additional space required by a card;
 * e.g. a display framebuffer.
 *
 * DIO-II ranges from select codes 132-255 at physical addresses given by:
 *	0x1000000 + (sc - 132) * 0x400000
 * The address range of DIO-II space is thus [0x1000000-0x20000000).
 *
 * DIO/DIO-II space is too large to map in its entirety, instead devices
 * are mapped into kernel virtual address space allocated from a range
 * of EIOMAPSIZE pages (vmparam.h) starting at ``extiobase''.
 */
#define	DIOBASE		(0x600000)
#define	DIOTOP		(0x1000000)
#define	DIOCSIZE	(0x10000)
#define	DIOIIBASE	(0x01000000)
#define	DIOIITOP	(0x20000000)
#define	DIOIICSIZE	(0x00400000)

/*
 * HP MMU
 */
#define	MMUBASE		IIOPOFF(0x5F4000)
#define	MMUSSTP		0x0
#define	MMUUSTP		0x4
#define	MMUTBINVAL	0x8
#define	MMUSTAT		0xC
#define	MMUCMD		MMUSTAT

#define	MMU_UMEN	0x0001	/* enable user mapping */
#define	MMU_SMEN	0x0002	/* enable supervisor mapping */
#define	MMU_CEN		0x0004	/* enable data cache */
#define	MMU_BERR	0x0008	/* bus error */
#define	MMU_IEN		0x0020	/* enable instruction cache */
#define	MMU_FPE		0x0040	/* enable 68881 FP coprocessor */
#define	MMU_WPF		0x2000	/* write protect fault */
#define	MMU_PF		0x4000	/* page fault */
#define	MMU_PTF		0x8000	/* page table fault */

#define	MMU_FAULT	(MMU_PTF|MMU_PF|MMU_WPF|MMU_BERR)
#define	MMU_ENAB	(MMU_UMEN|MMU_SMEN|MMU_IEN|MMU_FPE)

/*
 * 68851 and 68030 MMU
 */
#define	PMMU_LVLMASK	0x0007
#define	PMMU_INV	0x0400
#define	PMMU_WP		0x0800
#define	PMMU_ALV	0x1000
#define	PMMU_SO		0x2000
#define	PMMU_LV		0x4000
#define	PMMU_BE		0x8000
#define	PMMU_FAULT	(PMMU_WP|PMMU_INV)

/*
 * 68040 MMU
 */
#define	MMU4_RES	0x001
#define	MMU4_TTR	0x002
#define	MMU4_WP		0x004
#define	MMU4_MOD	0x010
#define	MMU4_CMMASK	0x060
#define	MMU4_SUP	0x080
#define	MMU4_U0		0x100
#define	MMU4_U1		0x200
#define	MMU4_GLB	0x400
#define	MMU4_BE		0x800

/* 680X0 function codes */
#define	FC_USERD	1	/* user data space */
#define	FC_USERP	2	/* user program space */
#define	FC_PURGE	3	/* HPMMU: clear TLB entries */
#define	FC_SUPERD	5	/* supervisor data space */
#define	FC_SUPERP	6	/* supervisor program space */
#define	FC_CPU		7	/* CPU space */

/* fields in the 68020 cache control register */
#define	IC_ENABLE	0x0001	/* enable instruction cache */
#define	IC_FREEZE	0x0002	/* freeze instruction cache */
#define	IC_CE		0x0004	/* clear instruction cache entry */
#define	IC_CLR		0x0008	/* clear entire instruction cache */

/* additional fields in the 68030 cache control register */
#define	IC_BE		0x0010	/* instruction burst enable */
#define	DC_ENABLE	0x0100	/* data cache enable */
#define	DC_FREEZE	0x0200	/* data cache freeze */
#define	DC_CE		0x0400	/* clear data cache entry */
#define	DC_CLR		0x0800	/* clear entire data cache */
#define	DC_BE		0x1000	/* data burst enable */
#define	DC_WA		0x2000	/* write allocate */

#define	CACHE_ON	(DC_WA|DC_BE|DC_CLR|DC_ENABLE|IC_BE|IC_CLR|IC_ENABLE)
#define	CACHE_OFF	(DC_CLR|IC_CLR)
#define	CACHE_CLR	(CACHE_ON)
#define	IC_CLEAR	(DC_WA|DC_BE|DC_ENABLE|IC_BE|IC_CLR|IC_ENABLE)
#define	DC_CLEAR	(DC_WA|DC_BE|DC_CLR|DC_ENABLE|IC_BE|IC_ENABLE)

/* 68040 cache control register */
#define	IC4_ENABLE	0x8000		/* instruction cache enable bit */
#define	DC4_ENABLE	0x80000000	/* data cache enable bit */

#define	CACHE4_ON	(IC4_ENABLE|DC4_ENABLE)
#define	CACHE4_OFF	(0)