| /freebsd-src/sys/contrib/device-tree/Bindings/pinctrl/ |
| H A D | pinctrl-single.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/pinctrl/pinctr
[all...] |
| H A D | pinmux-node.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/pinctrl/pinmux-node.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Generic Pin Multiplexing Node
10 - Linus Walleij <linus.walleij@linaro.org>
13 The contents of the pin configuration child nodes are defined by the binding
14 for the individual pin controller device. The pin configuration nodes need not
15 be direct children of the pin controller device; they may be grandchildren,
18 the binding for the individual pin controller device.
[all …]
|
| H A D | pinctrl-single.txt | 1 One-register-per-pin type device tree based pinctrl driver
4 - compatible : "pinctrl-single" or "pinconf-single".
5 "pinctrl-single" means that pinconf isn't supported.
6 "pinconf-single" means that generic pinconf is supported.
8 - reg : offset and length of the register set for the mux registers
10 - #pinctrl-cells : number of cells in addition to the index, set to 1
11 or 2 for pinctrl-single,pins and set to 2 for pinctrl-single,bits
13 - pinctrl-single,register-width : pinmux register access width in bits
15 - pinctrl-single,function-mask : mask of allowed pinmux function bits
19 - pinctrl-single,function-off : function off mode for disabled state if
[all …]
|
| H A D | atmel,at91-pinctrl.txt | 10 Please refer to pinctrl-bindings.txt in this directory for details of the
11 common pinctrl bindings used by client devices, including the meaning of the
12 phrase "pin configuration node".
14 Atmel AT91 pin configuration node is a node of a group of pins which can be
16 of the pins in that group. The 'pins' selects the function mode(also named pin
17 mode) this pin can work on and the 'config' configures various pad settings
18 such as pull-up, multi drive, etc.
21 - compatible: "atmel,at91rm9200-pinctr
[all...] |
| H A D | ste,nomadik.txt | 4 - compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl",
5 "stericsson,stn8815-pinctrl"
6 - nomadik-gpio-chips: array of phandles to the corresponding GPIO chips
7 (these have the register ranges used by the pin controller).
8 - prcm: phandle to the PRCMU managing the back end of this pin controller
10 Please refer to pinctrl-bindings.txt in this directory for details of the
11 common pinctrl bindings used by client devices, including the meaning of the
12 phrase "pin configuration node".
14 ST Ericsson's pin configuration nodes act as a container for an arbitrary number of
16 pin, a group, or a list of pins or groups. This configuration can include the
[all …]
|
| H A D | qcom,sm8150-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,sm8150-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
17 - reg-names:
19 Value type: <prop-encoded-array>
23 - interrupts:
25 Value type: <prop-encoded-array>
28 - interrupt-controller:
33 - #interrupt-cells:
[all …]
|
| H A D | qcom,sc7180-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,sc7180-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
17 - reg-names:
19 Value type: <prop-encoded-array>
23 - interrupts:
25 Value type: <prop-encoded-array>
28 - interrupt-controller:
33 - #interrupt-cells:
[all …]
|
| H A D | qcom,pmic-mpp.txt | 1 Qualcomm PMIC Multi-Purpose Pin (MPP) block
6 - compatible:
10 "qcom,pm8018-mpp",
11 "qcom,pm8019-mpp",
12 "qcom,pm8038-mpp",
13 "qcom,pm8058-mpp",
14 "qcom,pm8821-mpp",
15 "qcom,pm8841-mpp",
16 "qcom,pm8916-mpp",
17 "qcom,pm8917-mpp",
[all …]
|
| H A D | qcom,sdm660-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,sdm660-pinctrl" or
10 "qcom,sdm630-pinctrl".
12 - reg:
14 Value type: <prop-encoded-array>
18 - reg-names:
24 - interrupts:
26 Value type: <prop-encoded-array>
29 - interrupt-controller:
34 - #interrupt-cells:
[all …]
|
| H A D | actions,s700-pinctrl.txt | 1 Actions Semi S700 Pin Controller
3 This binding describes the pin controller found in the S700 SoC.
7 - compatible: Should be "actions,s700-pinctrl"
8 - reg: Should contain the register base address and size of
9 the pin controller.
10 - clocks: phandle of the clock feeding the pin controller
11 - gpio-controller: Marks the device node as a GPIO controller.
12 - gpio-ranges: Specifies the mapping between gpio controller and
13 pin-controller pins.
14 - #gpio-cells: Should be two. The first cell is the gpio pin number
[all …]
|
| H A D | qcom,mdm9615-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,mdm9615-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | lantiq,pinctrl-falcon.txt | 4 - compatible: "lantiq,pinctrl-falcon"
5 - reg: Should contain the physical address and length of the gpio/pinmux
8 Please refer to pinctrl-bindings.txt in this directory for details of the
9 common pinctrl bindings used by client devices, including the meaning of the
10 phrase "pin configuration node".
12 Lantiq's pin configuration nodes act as a container for an arbitrary number of
14 pin, a group, or a list of pins or groups. This configuration can include the
15 mux function to select on those group(s), and two pin configuration parameters:
16 pull-up and open-drain
22 other words, a subnode that lists a mux function but no pin configuration
[all …]
|
| H A D | bitmain,bm1880-pinctrl.txt | 1 Bitmain BM1880 Pin Controller
3 This binding describes the pin controller found in the BM1880 SoC.
7 - compatible: Should be "bitmain,bm1880-pinctrl"
8 - reg: Offset and length of pinctrl space in SCTRL.
10 Please refer to pinctrl-bindings.txt in this directory for details of the
11 common pinctrl bindings used by client devices, including the meaning of the
12 phrase "pin configuration node".
14 The pin configuration nodes act as a container for an arbitrary number of
16 pin, a group, or a list of pins or groups. This configuration for BM1880 SoC
17 includes pinmux and various pin configuration parameters, such as pull-up,
[all …]
|
| H A D | qcom,msm8960-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,msm8960-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,apq8084-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,apq8084-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,ipq8074-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,ipq8074-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,msm8976-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,msm8976-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,sdm845-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,sdm845-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,msm8994-pinctrl.txt | 6 - compatible:
10 "qcom,msm8992-pinctrl",
11 "qcom,msm8994-pinctrl".
13 - reg:
15 Value type: <prop-encoded-array>
18 - interrupts:
20 Value type: <prop-encoded-array>
23 - interrupt-controller:
28 - #interrupt-cells:
31 Definition: must be 2. Specifying the pin number and flags, as defined
[all …]
|
| H A D | actions,s900-pinctrl.txt | 1 Actions Semi S900 Pin Controller
3 This binding describes the pin controller found in the S900 SoC.
7 - compatible: Should be "actions,s900-pinctrl"
8 - reg: Should contain the register base address and size of
9 the pin controller.
10 - clocks: phandle of the clock feeding the pin controller
11 - gpio-controller: Marks the device node as a GPIO controller.
12 - gpio-ranges: Specifies the mapping between gpio controller and
13 pin-controller pins.
14 - #gpio-cells: Should be two. The first cell is the gpio pin number
[all …]
|
| H A D | qcom,msm8998-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,msm8998-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,msm8916-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,msm8916-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
16 - interrupts:
18 Value type: <prop-encoded-array>
21 - interrupt-controller:
26 - #interrupt-cells:
29 Definition: must be 2. Specifying the pin number and flags, as defined
30 in <dt-bindings/interrupt-controller/irq.h>
[all …]
|
| H A D | qcom,qcs404-pinctrl.txt | 6 - compatible:
9 Definition: must be "qcom,qcs404-pinctrl"
11 - reg:
13 Value type: <prop-encoded-array>
17 - reg-names:
23 - interrupts:
25 Value type: <prop-encoded-array>
28 - interrupt-controller:
33 - #interrupt-cells:
36 Definition: must be 2. Specifying the pin number and flags, as defined
[all …]
|
| H A D | fsl,mxs-pinctrl.txt | 1 * Freescale MXS Pin Controller
3 The pins controlled by mxs pin controller are organized in banks, each bank
4 has 32 pins. Each pin has 4 multiplexing functions, and generally, the 4th
6 voltage and pull-up.
9 - compatible: "fsl,imx23-pinctrl" or "fsl,imx28-pinctrl"
10 - reg: Should contain the register physical address and length for the
11 pin controller.
13 Please refer to pinctrl-bindings.txt in this directory for details of the
14 common pinctrl bindings used by client devices.
16 The node of mxs pin controller acts as a container for an arbitrary number of
[all …]
|
| H A D | canaan,k210-fpioa.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/pinctrl/canaan,k210-fpioa.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Damien Le Moal <dlemoal@kernel.org>
13 The Canaan Kendryte K210 SoC Fully Programmable IO Array (FPIOA)
15 48 IO pins of the SoC. Pin function configuration is performed on
16 a per-pin basis.
20 const: canaan,k210-fpioa
29 - description: Controller reference clock source
[all …]
|