Home
last modified time | relevance | path

Searched +full:mdio +full:- +full:parent +full:- +full:bus (Results 1 – 25 of 467) sorted by relevance

12345678910>>...19

/freebsd-src/sys/contrib/device-tree/Bindings/net/
H A Dmdio-mux.txt1 Common MDIO bus multiplexer/switch properties.
3 An MDIO bus multiplexer/switch will have several child busses that are
4 numbered uniquely in a device dependent manner. The nodes for an MDIO
5 bus multiplexer/switch will have one child node for each child bus.
8 - #address-cells = <1>;
9 - #size-cells = <0>;
12 - mdio-parent-bus : phandle to the parent MDIO bus.
14 - Other properties specific to the multiplexer/switch hardware.
17 - #address-cells = <1>;
18 - #size-cells = <0>;
[all …]
H A Dmdio-mux-multiplexer.txt1 Properties for an MDIO bus multiplexer consumer device
3 This is a special case of MDIO mux when MDIO mux is defined as a consumer
7 Required properties in addition to the MDIO Bus multiplexer properties:
9 - compatible : should be "mmio-mux-multiplexer"
10 - mux-controls : mux controller node to use for operating the mux
11 - mdio-parent-bus : phandle to the parent MDIO bus.
13 each child node of mdio bus multiplexer consumer device represent a mdio
14 bus.
17 Documentation/devicetree/bindings/mux/mux-controller.txt
18 and Documentation/devicetree/bindings/net/mdio-mux.txt
[all …]
H A Dmdio-mux-gpio.txt1 Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
3 This is a special case of a MDIO bus multiplexer. One or more GPIO
4 lines are used to control which child bus is connected.
8 - compatible : mdio-mux-gpio.
9 - gpios : GPIO specifiers for each GPIO line. One or more must be specified.
14 /* The parent MDIO bus. */
15 smi1: mdio@1180000001900 {
16 compatible = "cavium,octeon-3860-mdio";
17 #address-cells = <1>;
18 #size-cells = <0>;
[all …]
H A Dmdio-mux-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of a MDIO bus multiplexer. One or more GPIO
14 lines are used to control which child bus is connected.
17 - $ref: /schemas/net/mdio-mux.yaml#
21 const: mdio-mux-gpio
[all …]
H A Dmdio-mux-mmioreg.txt1 Properties for an MDIO bus multiplexer controlled by a memory-mapped device
3 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
4 like an FPGA, is used to control which child bus is connected. The mdio-mux
5 node must be a child of the memory-mapped device. The driver currently only
6 supports devices with 8, 16 or 32-bit registers.
10 - compatible : string, must contain "mdio-mux-mmioreg"
12 - reg : integer, contains the offset of the register that controls the bus
16 - mux-mask : integer, contains an eight-bit mask that specifies which
17 bits in the register control the actual bus multiplexer. The
18 'reg' property of each child mdio-mux node must be constrained by
[all …]
H A Dallwinner,sun8i-a83t-emac.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/allwinner,sun8i-a83t-emac.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Chen-Yu Tsai <wens@csie.org>
11 - Maxime Ripard <mripard@kernel.org>
16 - const: allwinner,sun8i-a83t-emac
17 - const: allwinner,sun8i-h3-emac
18 - const: allwinner,sun8i-r40-gmac
19 - const: allwinner,sun8i-v3s-emac
[all …]
H A Dmdio-mux-multiplexer.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-multiplexer.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer consumer device
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of MDIO mux when MDIO mux is defined as a consumer
19 - $ref: /schemas/net/mdio-mux.yaml#
23 const: mdio-mux-multiplexer
25 mux-controls:
[all …]
H A Dmdio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Common MDIO bus multiplexer/switch properties.
10 - Andrew Lunn <andrew@lunn.ch>
13 An MDIO bus multiplexer/switch will have several child busses that are
14 numbered uniquely in a device dependent manner. The nodes for an MDIO
15 bus multiplexer/switch will have one child node for each child bus.
18 mdio-parent-bus:
[all …]
H A Dbrcm,bcmgenet.txt4 - compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2",
5 "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5", "brcm,bcm2711-genet-v5" or
6 "brcm,bcm7712-genet-v5".
7 - reg: address and length of the register set for the device
8 - interrupts and/or interrupts-extended: must be two cells, the first cell
11 optional third interrupt cell for Wake-on-LAN can be specified.
12 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
14 - phy-mode: see ethernet.txt file in the same directory
15 - #address-cells: should be 1
16 - #size-cells: should be 1
[all …]
H A Damlogic,gxl-mdio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/net/amlogic,gxl-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Amlogic GXL MDIO bus multiplexer
10 - Jerome Brunet <jbrunet@baylibre.com>
13 This is a special case of a MDIO bus multiplexer. It allows to choose between
14 the internal mdio bus leading to the embedded 10/100 PHY or the external
15 MDIO bus on the Amlogic GXL SoC family.
18 - $ref: mdio-mux.yaml#
[all …]
H A Dmdio-mux-meson-g12a.txt1 Properties for the MDIO bus multiplexer/glue of Amlogic G12a SoC family.
3 This is a special case of a MDIO bus multiplexer. It allows to choose between
4 the internal mdio bus leading to the embedded 10/100 PHY or the external
5 MDIO bus.
8 - compatible : amlogic,g12a-mdio-mux
9 - reg: physical address and length of the multiplexer/glue registers
10 - clocks: list of clock phandle, one for each entry clock-names.
11 - clock-names: should contain the following:
18 mdio_mux: mdio-multiplexer@4c000 {
19 compatible = "amlogic,g12a-mdio-mux";
[all …]
H A Dmdio-mux-mmioreg.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-mmioreg.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer controlled by a memory-mapped device
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
14 like an FPGA, is used to control which child bus is connected. The mdio-mux
15 node must be a child of the memory-mapped device. The driver currently only
16 supports devices with 8, 16 or 32-bit registers.
[all …]
H A Damlogic,g12a-mdio-mux.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/net/amlogic,g12a-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MDIO bus multiplexer/glue of Amlogic G12a SoC family
10 This is a special case of a MDIO bus multiplexer. It allows to choose between
11 the internal mdio bus leading to the embedded 10/100 PHY or the external
12 MDIO bus.
15 - Neil Armstrong <neil.armstrong@linaro.org>
18 - $ref: mdio-mux.yaml#
[all …]
H A Dfsl-enetc.txt9 - reg : Specifies PCIe Device Number and Function
11 to parent node bindings.
12 - compatible : Should be "fsl,enetc".
14 1. The ENETC external port is connected to a MDIO configurable phy
16 1.1. Using the local ENETC Port MDIO interface
18 In this case, the ENETC node should include a "mdio" sub-node
19 that in turn should contain the "ethernet-phy" node describing the
26 - phy-handle : Phandle to a PHY on the MDIO bus.
29 - phy-connection-type : Defined in ethernet.txt.
31 - mdio : "mdio" node, defined in mdio.txt.
[all …]
/freebsd-src/sys/contrib/device-tree/Bindings/net/dsa/
H A Dmarvell.txt2 ---------------------------------------
10 Marvell Switches are MDIO devices. The following properties should be
11 placed as a child node of an mdio device.
17 which is at a different MDIO base address in different switch families.
18 - "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
22 - "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
24 - "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model:
28 - compatible : Should be one of "marvell,mv88e6085",
31 - reg : Address on the MII bus for the switch.
35 - reset-gpios : Should be a gpio specifier for a reset line
[all …]
H A Dar9331.txt1 Atheros AR9331 built-in switch
4 It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
5 MDIO bus. All PHYs are built-in as well.
9 - compatible: should be: "qca,ar9331-switch"
10 - reg: Address on the MII bus for the switch.
11 - resets : Must contain an entry for each entry in reset-names.
12 - reset-names : Must include the following entries: "switch"
13 - interrupt-parent: Phandle to the parent interrupt controller
14 - interrupts: IRQ line for the switch
15 - interrupt-controller: Indicates the switch is itself an interrupt
[all …]
H A Drealtek-smi.txt1 Realtek SMI-based Switches
4 The SMI "Simple Management Interface" is a two-wire protocol using
5 bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
6 not use the MDIO protocol. This binding defines how to specify the
7 SMI-based Realtek devices.
11 - compatible: must be exactly one of:
23 - mdc-gpios: GPIO line for the MDC clock line.
24 - mdio-gpios: GPIO line for the MDIO data line.
25 - reset-gpios: GPIO line for the reset signal.
28 - realtek,disable-leds: if the LED drivers are not used in the
[all …]
/freebsd-src/sys/contrib/device-tree/Bindings/mux/
H A Dreg-mux.txt1 Generic register bitfield-based multiplexer controller bindings
3 Define register bitfields to be used to control multiplexers. The parent
7 - compatible : should be one of
8 "reg-mux" : if parent device of mux controller is not syscon device
9 "mmio-mux" : if parent device of mux controller is syscon device
10 - #mux-control-cells : <1>
11 - mux-reg-masks : an array of register offset and pre-shifted bitfield mask
13 * Standard mux-controller bindings as decribed in mux-controller.txt
16 - idle-states : if present, the state the muxes will have when idle. The
21 pair in the mux-reg-masks array.
[all …]
H A Dreg-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mux/reg-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Generic register bitfield-based multiplexer controller
10 - Peter Rosin <peda@axentia.se>
13 Define register bitfields to be used to control multiplexers. The parent
19 - reg-mux # parent device of mux controller is not syscon device
20 - mmio-mux # parent device of mux controller is syscon device
24 '#mux-control-cells':
[all …]
/freebsd-src/sys/arm64/broadcom/brcmmdio/
H A Dmdio_mux_iproc.c1 /*-
29 #include <sys/bus.h>
39 #include <machine/bus.h>
86 /* OFW bus interface */
99 MALLOC_DEFINE(M_BRCM_IPROC_MDIO, "Broadcom IPROC MDIO",
100 "Broadcom IPROC MDIO dynamic memory");
114 /* Bus interface */
127 /* MDIO interface */
144 {"brcm,mdio-mu
257 brcm_iproc_mdio_write_mux(device_t dev,int bus,int phy,int reg,int val) brcm_iproc_mdio_write_mux() argument
272 brcm_iproc_mdio_read_mux(device_t dev,int bus,int phy,int reg) brcm_iproc_mdio_read_mux() argument
303 phandle_t node, parent; brcm_iproc_mdio_attach() local
[all...]
H A Dmdio_nexus_iproc.c1 /*-
29 #include <sys/bus.h>
39 #include <machine/bus.h>
44 MALLOC_DEFINE(M_BRCM_IPROC_NEXUS, "Broadcom IPROC MDIO NEXUS",
45 "Broadcom IPROC MDIO NEXUS dynamic memory");
52 /* OFW bus interface */
71 /* Bus interface */
84 /* MDIO interface */
85 /* MDIO interface */
114 sc->mux_i in brcm_mdionexus_mdio_readreg()
195 phandle_t parent, node; brcm_mdionexus_ofw_bus_attach() local
[all...]
/freebsd-src/sys/contrib/device-tree/src/powerpc/
H A Dmpc7448hpc2.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
9 /dts-v1/;
14 #address-cells = <1>;
15 #size-cells = <1>;
28 #address-cells = <1>;
29 #size-cells =<0>;
34 d-cache-line-size = <32>; // 32 bytes
35 i-cache-line-size = <32>; // 32 bytes
36 d-cache-size = <0x8000>; // L1, 32K bytes
37 i-cache-size = <0x8000>; // L1, 32K bytes
[all …]
H A Dkmeter1.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
5 * 2008-2011 DENX Software Engineering GmbH
8 /dts-v1/;
13 #address-cells = <1>;
14 #size-cells = <1>;
28 #address-cells = <1>;
29 #size-cells = <0>;
34 d-cache-line-size = <32>; // 32 bytes
35 i-cache-line-size = <32>; // 32 bytes
36 d-cache-size = <32768>; // L1, 32K
[all …]
/freebsd-src/sys/contrib/device-tree/src/arm/nxp/vf/
H A Dvf610-zii-dev-rev-c.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 /dts-v1/;
7 #include "vf610-zii-dev.dtsi"
11 compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610";
13 mdio-mux {
14 compatible = "mdio-mux-gpio";
15 pinctrl-0 = <&pinctrl_mdio_mux>;
16 pinctrl-names = "default";
20 mdio-parent-bus = <&mdio1>;
21 #address-cells = <1>;
[all …]
/freebsd-src/sys/dev/mdio/
H A Dmdio.c1 /*-
2 * Copyright (c) 2011-2012 Stefan Bethke.
28 #include <sys/bus.h>
32 #include <dev/mdio/mdio.h>
37 mdio_identify(driver_t *driver, device_t parent) in mdio_identify() argument
40 if (device_find_child(parent, mdio_driver.name, -1) == NULL) in mdio_identify()
41 BUS_ADD_CHILD(parent, 0, mdio_driver.name, DEVICE_UNIT_ANY); in mdio_identify()
48 device_set_desc(dev, "MDIO"); in mdio_probe()
[all...]

12345678910>>...19