| /freebsd-src/sys/contrib/device-tree/Bindings/bus/ |
| H A D | baikal,bt1-axi.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/bus/baikal,bt1-axi.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Baikal-T1 AXI-bus
11 - Serge Semin <fancer.lancer@gmail.com>
14 AXI3-bus is the main communication bus of Baikal-T1 SoC connecting all
15 high-speed peripheral IP-cores with RAM controller and with MIPS P5600
16 cores. Traffic arbitration is done by means of DW AXI Interconnect (so
17 called AXI Main Interconnect) routing IO requests from one block to
[all …]
|
| H A D | brcm,bus-axi.txt | 1 Driver for ARM AXI Bus with Broadcom Plugins (bcma)
5 - compatible : brcm,bus-axi
7 - reg : iomem address range of chipcommon core
9 The cores on the AXI bus are automatically detected by bcma with the
13 them manually through device tree. Use an interrupt-map to specify the
14 IRQ used by the devices on the bus. The first address is just an index,
17 The top-level axi bus may contain children representing attached cores
24 axi@18000000 {
25 compatible = "brcm,bus-axi";
28 #address-cells = <1>;
[all …]
|
| H A D | baikal,bt1-apb.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/bus/baikal,bt1-apb.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Baikal-T1 APB-bus
11 - Serge Semin <fancer.lancer@gmail.com>
14 Baikal-T1 CPU or DMAC MMIO requests are handled by the AMBA 3 AXI Interconnect
15 which routes them to the AXI-APB bridge. This interface is a single master
16 multiple slaves bus in turn serializing IO accesses and routing them to the
22 - $ref: /schemas/simple-bus.yaml#
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/dma/ |
| H A D | adi,axi-dmac.txt | 1 Analog Devices AXI-DMAC DMA controller
4 - compatible: Must be "adi,axi-dmac-1.00.a".
5 - reg: Specification for the controllers memory mapped register map.
6 - interrupts: Specification for the controllers interrupt.
7 - clocks: Phandle and specifier to the controllers AXI interface clock
8 - #dma-cells: Must be 1.
10 Required sub-nodes:
11 - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
12 the channel sub-nodes the following bindings apply. They must match the
15 Required properties for adi,channels sub-node:
[all …]
|
| H A D | snps,dw-axi-dmac.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/dma/snps,dw-ax
[all...] |
| /freebsd-src/sys/contrib/device-tree/Bindings/clock/ |
| H A D | baikal,bt1-ccu-div.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/clock/baikal,bt1-cc
[all...] |
| H A D | starfive,jh7110-aoncrg.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/clock/starfive,jh7110-aoncrg.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: StarFive JH7110 Always-On Clock and Reset Generator
10 - Emil Renner Berthing <kernel@esmil.dk>
14 const: starfive,jh7110-aoncrg
21 - items:
22 - description: Main Oscillator (24 MHz)
23 - description: GMAC0 RMII reference or GMAC0 RGMII RX
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/pci/ |
| H A D | qcom,pcie.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schema
[all...] |
| H A D | xilinx-pcie.txt | 1 * Xilinx AXI PCIe Root Port Bridge DT description
4 - #address-cells: Address representation for root ports, set to <3>
5 - #size-cells: Size representation for root ports, set to <2>
6 - #interrupt-cells: specifies the number of cells needed to encode an
8 - compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
9 - reg: Should contain AXI PCIe registers location and length
10 - device_type: must be "pci"
11 - interrupts: Should contain AXI PCIe interrupt
12 - interrupt-map-mask,
13 interrupt-map: standard PCI properties to define the mapping of the
[all …]
|
| H A D | qcom,pcie.txt | 3 - compatible:
7 - "qcom,pcie-ipq8064" for ipq8064
8 - "qcom,pcie-ipq8064-v2" for ipq8064 rev 2 or ipq8065
9 - "qcom,pcie-apq8064" for apq8064
10 - "qcom,pcie-apq8084" for apq8084
11 - "qcom,pcie-msm8996" for msm8996 or apq8096
12 - "qcom,pcie-ipq4019" for ipq4019
13 - "qcom,pcie-ipq8074" for ipq8074
14 - "qcom,pcie-qcs404" for qcs404
15 - "qcom,pcie-sc8180x" for sc8180x
[all …]
|
| H A D | snps,dw-pcie-common.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/pci/snps,dw-pcie-common.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jingoo Han <jingoohan1@gmail.com>
11 - Gustavo Pimentel <gustavo.pimentel@synopsys.com>
22 DWC PCIe CSR space is normally accessed over the dedicated Data Bus
23 Interface - DBI. In accordance with the reference manual the register
24 configuration space belongs to the Configuration-Dependent Module (CDM)
25 and is split up into several sub-parts Standard PCIe configuration
[all …]
|
| H A D | brcm,iproc-pcie.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/pci/brcm,iproc-pci
[all...] |
| /freebsd-src/sys/contrib/device-tree/Bindings/net/ |
| H A D | xilinx_axienet.txt | 1 XILINX AXI ETHERNET Device Tree Bindings
2 --------------------------------------------------------
4 Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
10 Management configuration is done through the AXI interface, while payload is
11 sent and received through means of an AXI DMA controller. This driver
12 includes the DMA driver code, so this driver is incompatible with AXI DMA
18 - compatible : Must be one of "xlnx,axi-ethernet-1.00.a",
19 "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
20 - reg : Address and length of the IO space, as well as the address
21 and length of the AXI DMA controller IO space, unless
[all …]
|
| H A D | snps,dwc-qos-ethernet.txt | 7 IP block. The IP supports multiple options for bus type, clocking and reset
13 - compatible: One of:
14 - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
15 Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
16 - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10"
18 - "snps,dwc-qos-ethernet-4.10"
20 "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be
22 - reg: Address and length of the register set for the device
23 - clocks: Phandle and clock specifiers for each entry in clock-names, in the
24 same order. See ../clock/clock-bindings.txt.
[all …]
|
| /freebsd-src/sys/contrib/alpine-hal/ |
| H A D | al_hal_udma_iofic.h | 1 /*-
10 found at http://www.gnu.org/licenses/gpl-2.0.html
56 /* *INDENT-OFF* */
60 /* *INDENT-ON* */
69 AL_IOFIC_MODE_LEGACY, /**< level-sensitive interrupt wire */
70 AL_IOFIC_MODE_MSIX_PER_Q, /**< per UDMA queue MSI-X interrupt */
82 * interrupt controller of each bus-master unit in the I/O Fabric.
142 * MSIX Bus generator response error, the Bus response received with error indication
146 * MSIx timeout MSIX Bus generator timeout error.
147 * The generator didn't receive bus response for the MSIx write transaction.
[all …]
|
| H A D | al_hal_udma_regs_s2m.h | 1 /*-
10 found at http://www.gnu.org/licenses/gpl-2.0.html
77 /* [0x24] AXI outstanding read configuration */
79 /* [0x28] AXI outstanding write configuration */
86 * 00 - No pending tasks
100 * 0 - Log is enable
101 * 1 - Log is masked.
131 /* [0x30] S2M AXI data FIFO status */
190 * [0x8] Counting the net length of the data buffers [64-bit]
195 * [0xc] Counting the net length of the data buffers [64-bit]
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/mmc/ |
| H A D | snps,dwcmshc-sdhci.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/mmc/snps,dwcmshc-sdhci.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ul
[all...] |
| H A D | marvell,xenon-sdhci.txt | 11 - compatible: should be one of the following
12 - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SoC.
13 Must provide a second register area and marvell,pad-type.
14 - "marvell,armada-ap806-sdhci": For controllers on Armada AP806.
15 - "marvell,armada-ap807-sdhci": For controllers on Armada AP807.
16 - "marvell,armada-cp110-sdhci": For controllers on Armada CP110.
18 - clocks:
21 CP110, the AXI clock is also mandatory.
23 - clock-names:
26 The input clock for the AXI bus must be named as "axi".
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/media/ |
| H A D | marvell,mmp2-ccic.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/media/marvell,mmp2-ccic.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Lubomir Rintel <lkundrak@v3.sk>
15 pattern: '^camera@[a-f0-9]+$'
18 const: marvell,mmp2-ccic
26 power-domains:
30 $ref: /schemas/graph.yaml#/$defs/port-base
35 $ref: video-interfaces.yaml#
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/soc/imx/ |
| H A D | fsl,imx8mm-disp-blk-ctrl.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/soc/imx/fsl,imx8mm-disp-blk-ctrl.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: NXP i.MX8MM DISP blk-ctrl
10 - Lucas Stach <l.stach@pengutronix.de>
13 The i.MX8MM DISP blk-ctrl is a top-level peripheral providing access to
20 - const: fsl,imx8mm-disp-blk-ctrl
21 - const: syscon
26 '#power-domain-cells':
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/spi/ |
| H A D | mediatek,spi-mtk-nor.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/spi/mediatek,spi-mtk-nor.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Bayi Cheng <bayi.cheng@mediatek.com>
11 - Chuanhong Guo <gch981213@gmail.com>
21 - $ref: /schemas/spi/spi-controller.yaml#
26 - enum:
27 - mediatek,mt8173-nor
28 - mediatek,mt8186-nor
[all …]
|
| H A D | adi,axi-spi-engine.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/spi/adi,axi-spi-engine.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Analog Devices AXI SPI Engine Controller
10 The AXI SPI Engine controller is part of the SPI Engine framework[1] and
11 allows memory mapped access to the SPI Engine control bus. This allows it
18 - Michael Hennerich <Michael.Hennerich@analog.com>
19 - Nuno Sá <nuno.sa@analog.com>
22 - $ref: /schemas/spi/spi-controller.yaml#
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/arm/ |
| H A D | microchip,sparx5.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lars Povlsen <lars.povlsen@microchip.com>
13 The Microchip Sparx5 SoC is a ARMv8-based used in a family of
14 gigabit TSN-capable gigabit switches.
16 The SparX-5 Ethernet switch family provides a rich set of switching
17 features such as advanced TCAM-based VLAN and QoS processing
19 TCAM-based frame processing using versatile content aware processor
27 - description: The Sparx5 pcb125 board is a modular board,
[all …]
|
| /freebsd-src/sys/contrib/device-tree/Bindings/w1/ |
| H A D | amd,axi-1wire-host.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/w1/amd,axi-1wire-host.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: AMD AXI 1-wire bus host for programmable logic
10 - Kris Chaplin <kris.chaplin@amd.com>
14 const: amd,axi-1wire-host
26 - compatible
27 - reg
28 - clocks
[all …]
|
| /freebsd-src/sys/contrib/device-tree/src/arm/marvell/ |
| H A D | pxa910.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
7 #include <dt-bindings/clock/marvell,pxa910.h>
10 #address-cells = <1>;
11 #size-cells = <1>;
22 #address-cells = <1>;
23 #size-cells = <1>;
24 compatible = "simple-bus";
25 interrupt-parent = <&intc>;
28 L2: l2-cache {
29 compatible = "marvell,tauros2-cache";
[all …]
|